• 한국운동역학회지
• /
• 제16권3호
• /
• pp.149-163
• /
• 2006

The purpose of this study was to compare the lower extremity's joint and segment coupling patterns between forward and backward running in subjects who were twelve healthy males. Three-dimensional kinematic data were collected with Qualisys system while subjects ran to forward and backward. The thigh internal/external rotation and tibia internal/external rotation, thigh flexion/extension and tibia flexion/extension, tibia internal/external rotation and foot inversion/eversion, knee internal/external rotation and ankle inversion/eversion, knee flexion/extension and ankle inversion/eversion, knee flexion/extension and ankle flexion/extension, and knee flexion/extension and tibia internal/external rotation coupling patterns were determined using a vector coding technique. The comparison for each coupling between forward and backward running were conducted using a dependent, two-tailed t-test at a significant level of .05 for the mean of each of five stride regions, midstance(1l-30%), toe-off(31-50%), swing acceleration(51-70%), swing deceleration(71-90), and heel-strike(91-10%), respectively. 1. The knee flexion/extension and ankle flexion/extension coupling pattern of both foreward and backward running over the stride was converged on a complete coordination. However, the ankle flexion/extension to knee flexion/extension was relatively greater at heel-strike in backward running compared with forward running. At the swing deceleration, backward running was dominantly led by the ankle flexion/extension, but forward running done by the knee flexion/extension. 2. The knee flexion/extension and ankle inversion/eversion coupling pattern for both running was also converged on a complete coordination. At the mid-stance. the ankle movement in the frontal plane was large during forward running, but the knee movement in the sagital plane was large during backward running and vice versa at the swing deceleration. 3. The knee flexion/extension and tibia internal/external rotation coupling while forward and backward run was also centered on the angle of 45 degrees, which indicate a complete coordination. However, tibia internal/external rotation dominated the knee flexion/extension at heel strike phase in forward running and vice versa in backward running. It was diametrically opposed to the swing deceleration for each running. 4. Both running was governed by the ankle movement in the frontal plane across the stride cycle within the knee internal/external rotation and tibia internal/external rotation. The knee internal/external rotation of backward running was greater than that of forward running at the swing deceleration. 5. The tibia internal/external rotation in coupling between the tibia internal/external rotation and foot inversion/eversion was relatively great compared with the foot inversion/eversion over a stride for both running. At heel strike, the tibia internal/external rotation of backward running was shown greater than that of forward(p<.05). 6. The thigh internal/external rotation took the lead for both running in the thigh internal/external rotation and tibia internal/external rotation coupling. In comparison of phase, the thigh internal/external rotation movement at the swing acceleration phase in backward running worked greater in comparison with forward running(p<.05). However, it was greater at the swing deceleration in forward running(p<.05). 7. With the exception of the swing deceleration phase in forward running, the tibia flexion/extension surpassed the thigh flexion/extension across the stride cycle in both running. Analysis of the specific stride phases revealed the forward running had greater tibia flexion/extension movement at the heel strike than backward running(p<.05). In addition, the thigh flexion/extension and tibia flexion/extension coupling displayed almost coordination at the heel strike phase in backward running. On the other hand the thigh flexion/extension of forward running at the swing deceleration phase was greater than the tibia flexion/extension, but it was opposite from backward running. In summary, coupling which were the knee flexion/extension and ankle flexion/extension, the knee flexion/extension and ankle inversion/eversion, the knee internal/external rotation and ankle inversion/eversion, the tibia internal/external rotation and foot inversion/eversion, the thigh internal/external rotation and tibia internal/external rotation, and the thigh flexion/extension and tibia flexion/extension patterns were most similar across the strike cycle in both running, but it showed that coupling patterns in the specific stride phases were different from average point of view between two running types.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.71-76
• /
• 2014

This Research focuses on how to maximize fuel economy improvement of I.S.G. while keeping 12V system. With 12V system the maximum gain of fuel economy with I.S.G. is known to be about 3~5% in FTP-75 mode because engine stop is only conducted in standstill idle. But in this study deceleration engine stop (engine speed is zero) has been tried additionally and the optimum condition for deceleration engine stop was found to maximize fuel economy improvement in practical point of view, the result of which is about 8.8% in FTP-75.

• 대한기계학회논문집B
• /
• 제40권5호
• /
• pp.313-319
• /
• 2016

액체가 부분적으로 채워져 있는 용기에서 발생하는 슬로싱 현상을 이해하고 이를 효과적으로 제어하는 것은 매우 중요하다. 선행 연구들이 대부분 사인파형(sinusoidal) 가진에 의한 슬로싱 및 공진 현상에 관심을 가진 반면, 본 연구에서는 산업 현장에서 액체 용기를 빠르게 이송시킬 때 발생하는 슬로싱을 이해하고 억제하고자 하였다. 즉, 사각 용기를 수평방향으로 빠르게 이송시킬 때 발생하는 2상 유동을 수치해석으로 구한 후, 용기의 속도 프로파일(특히 가속 및 감속 시간)이 슬로싱에 미치는 영향을 분석하였다. 그 결과 용기의 가감속 시간이 1차 모드 고유주기의 정수배가 될 때 슬로싱이 상당히 억제되는 것을 관찰하였고, 이는 슬로싱 억제 방안으로 활용될 수 있을 것으로 기대된다.

• 설비공학논문집
• /
• 제15권3호
• /
• pp.177-186
• /
• 2003

In the present study, the flow characteristics of developing turbulent flows are investigated at the exit region of a square cross-sectional 180" curved duct with dimensions of 40mm$\times$40mm$\times$4000mm (height $\times$ width $\times$length). Smoke particles produced from mosquito coils were used as seed particles for the LDV measurement. Experiments were carried out to measure axial velocity profiles, shear stress distributions and entrance lengths by using an LDV system and Rotating Machinery Resolver RMR with PHASE software. Experimental results clearly show that the time-averaged Reynolds number does not affect oscillatory flow characteristics because the turbulent components tend to balance the oscillatory components in the fully developed flow region. Also, the velocity profiles are in good agreement with 1/7power law such as the results of steady turbulent flows. The turbulent intensity linearly increases along the walls and is slightly higher, especially in the period of deceleration. On the other hand, the LDV measurements show that shear stress values in slightly higher in the period of deceleration due to the flow characteristics in the exit region. The entrance length where flows become stable appears at the point that is 40 times the length of hydraulic diameter.eter.

• 대한교통학회지
• /
• 제28권4호
• /
• pp.7-18
• /
• 2010

본 연구는 고속도로 영업소 진출부의 차량속도와 상충발생을 조사하여 상대속도 및 상충으로 인한 차량 감속시간 등을 분석한 결과 상대속도가 클수록 상충으로 인한 차량 급감속이 발생한다는 문제점을 파악하였으며 특히 운영형태가 상이한 지점들을 비교 분석하여 차로 운영 형태에 따라 상충 및 상대속도가 다름을 확인할 수 있었다. 이러한 관찰을 통하여 하이패스 차량과 일반차량간 상대속도에 의한 사고 위험성을 정량적으로 비교 분석하였다. 그 결과 하이패스 차량과 일반차량간 합류가 하이패스차량간 합류보다 사고위험이 더 높은 것으로 분석되었다. 이는 차량간 상대속도차가 클수록 상충시 급감속 및 감속시간이 큼에 따라 사고 위험이 높은 것으로 분석되었다. 또한 합류 시점부가 영업소 진출 후 가까울수록 상대속도가 큼에 따라 상충시 TA분석값이 낮은 것으로 분석되었다. 영업소 진출부에서 발생하는 상대속도차에 의한 상충을 분석하였으며 이를 통해 급감속 및 사고발생을 줄일 수 있는 대안을 제시 영업소 내 하이패스 차로 설치시 안전성을 높여줄 수 있을 것으로 기대된다.

• 대한토목학회논문집
• /
• 제30권1D호
• /
• pp.1-10
• /
• 2010

고속도로 영업소의 경우 하이패스차량과 일반TCS이용차량간의 혼용 및 차로변경으로 인한 상충이 발생하는 구간으로 안전성에 대한 검토가 필요한 구간이다. 본 연구에서는 영업소 진출부에 설치된 중앙하이패스 이용차량과 일반차로 이용차량간의 상충 및 사고위험성을 현장비디오촬영 및 상충분석을 통해 알아보았다. 차량속도와 상대속도 및 상충으로 인한 차량 감속시간 등을 분석한 결과 하이패스이용차량과 일반TCS이용차량간의 상대속도가 클수록 상충으로 인한 차량 급감속이 발생한다는 문제점을 파악하였으며, 중앙 하이패스 설치시 상충 발생 위치 및 차로 운영형태에 따라 상충빈도 및 상대속도가 다름을 확인할 수 있었다. TA(Time to Accident)분석 결과, 고속도로 영업소 중앙 하이패스 설치시 차량간 상대속도, 상충위치 및 빈도에 따른 상충시 하이패스 차량의 급감속 및 감속시간이 큼에 따라 사고위험이 높은 것으로 분석되었다. 또한 합류 시점부가 영업소 진출부와 가까울수록 TA분석값이 낮은 것으로 분석되어 전반적으로 속도차이를 줄여 안전성을 증대시켜야 함을 알 수 있었다. 본 연구에서는 영업소 진출부 중앙 하이패스 설치로 발생하는 상대속도차에 의한 상충으로 급감속 및 사고를 억제함으로서 영업소 중앙 하이패스 차로 설치시 안전성을 높여줄 수 있을 것으로 기대된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.274-279
• /
• 2009

Reduction Gear Box where from productive site uses the gear with power delivery with high mechanical efficiency of power a deceleration and as the mechanical element union product which has the velocity ratio which is various together is produced with the power occurrence motor and leads gets a high driving force is plentifully used. The above occurs from gear drive issue sound Whine, Noise and Vibration as occurring from the rim process which the gear will bite mainly is delivered with the case etc. gear drive whole which leads the axis and the bearing. The productivity falls with the going straight rate decrease which with like this problem point is caused by with rework the problem point where the cost of production rises under improving boil many kinds analyzed the plan and investigates the resultant acceleration sensor which and a frequency analysis system and was made to apply.

• 한국자동차공학회논문집
• /
• 제13권1호
• /
• pp.19-27
• /
• 2005

The spray characteristics of DISI injector has a great role in engine efficiency and emission. Thus, many researchers have been studied to investigate the spray characteristics of hollow cone type and slit type injector which are used in DISI engine. In this study, we tried to provide spray parameters which effect on the spray characteristics such as injection pressure, ambient pressure and ambient temperature. In addition, we calculated $t_b\;and\;t_c$ to investigate the break up mechanism of test injectors and also obtained $C_v$ to evaluate the spray characteristics. From this study, As the ambient pressure increases in case of slit injector, $C_v$ decreases.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.827-828
• /
• 2006

This paper presents a vehicle control algorithm for Personal Rapid Transit (PRT) system. PRT system is a one-way direction network system which is composed of guideway branches, merging/diverging points. Vehicle control algorithm can be divided into two kinds. Those are merging control algorithm and the other. We emphasized on the merging control algorithm. For that, we first devised a front/virtual front vehicle finding strategies. Properly determined front/virtual front vehicle is the starting point of vehicle control. The objects of merging control are to avoid collision and to pass the merging point fluently. Which implies that jerk constraint and limits of acceleration and deceleration etc. are should be considered. To verify the validation of the vehicle algorithm, we executed simulations and presented test results.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.252-257
• /
• 2000

This paper describes a look-ahead algorithm of PCNC(personal computer numerical control). The algorithm is based on acceleration/deceleration before interpolation never including a command error and determines a velocity value in end point of each block(or start point of each block). The algorithm is represented as following; 1) calculating two maximum arrival velocity(v1, v2) by a acceleration value, a command velocity and distance in a previous block and a next block, 2) getting a tangent velocity(v3) of the adjacent blocks, 3) choosing a minimum value among these three velocities, and 4) setting the value to a velocity of a start point of the next block(or a end point of the previous block). The proposed look-ahead algorithm was implemented and tested by using a commercial RTOS(real time operation system) on the MS-Windows NT 4.0 in a PC platform. For interfacing to a machine, a counter board, a DAC board and a DIO board were used. The result of the algorithm increased a machining precision and a machining speed in many short blocks.