• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.693-696
• /
• 1999

This paper describes a new voltage recorder for the voltage management of a power distribution line by using a new voltage measurement technique. The RMS(Root Mean Square) voltage measurement for the power line under the assumption of a sinusoidal input voltage is taken by the full-wave rectifier, half-adder utilizing operational amplifier(OP) circuit. A/D converter utilizing a dual slope converter converts an analog voltage signal into a serial pulse. The pulse is counted with a single chip micro-controller, converted with the RMS voltage, and saved into a flash memory. In the last, a new voltage recorder with compact size and multifunction is developed. Also, Voltage Management System that can analyze the stored data via RS-232C cable is developed based on Windows 95 and Visual C++.

• International Journal of Internet, Broadcasting and Communication
• /
• v.5 no.2
• /
• pp.11-14
• /
• 2013

This paper describes the sigma-delta ADC/DAC digital block with two channels. The ADC block has comb filter and three half band filters. And the DAC block has 5th Cascaded-of-Integrators Feedback DSM. The ADC and DAC support I2S, RJ, LJ and selectable input data modes of 24bit, 20bit, and 16bit. It is fabricated with 0.35um Hynix standard CMOS cell library. The chip size is 3700*3700um. It has been verified using NC Verilog Simulator and Matlab Tool.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.93-96
• /
• 1999

Solar cell generate DC power from sunlight whose power is different at any instance according to condition of variables : insolation and temperature. In order to improve the system utility factor and efficiency of energy conversion, it is desirable to operate the PV system at maximum power point of solar cell under different condition. In this paper, Boost chopper is controlled it output voltage with a new discrete control algorithm for MPPT. PWM signal of DC-DC converter are generated with a 89C51 microcontroller. Switching frequency of DC-DC converter is set at 10KHz. Simulation and experimental results show that the PV system studied in this paper is always operated at maximum power point under different maximum power point of solar cells having stabilized output voltage waveform with relatively small ripple component

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.310-312
• /
• 1989

From the viewpoint of an effective energy use, many method for reactive power compensation has been developed. Among of the reactive power compensation, this paper describes the relation of operation interpretation, filter, hysteresis width and switching time of current controlled PWM converter which has excellent reactive power compensation. This current controlled PWM convertor is excellent the view of reactive power compensation by current control method using hysteresis comparator method, but is required element of high response characteristics. Therefore this paper offers the series of data for system considering switching characteristics of switching element.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.540-542
• /
• 1999

We develop jumping ring system with sensor and control system using dynamic neural networks. Jumping ring, sensor and control system are controlled by 586 PC using Turbo C program. Sensor system is composed of 20 optical sensors and encoder. The control circuits are consisted of thyristor, FET and phase controller. A/D converter and optical sensor acquire real time motion data of the jumping ring system. The information of acquired jumping ring Position is estimated by using dynamic neural networks. Estimated control signals are sent to control circuits and D/A converter to track desired position of the jumping ring system. Experiment results are given to verify that proposed dynamic controller is useful in real jumping ring system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.586-589
• /
• 2001

This paper focuses on a method to connect mobile devices such as mobile robot, Automated Guided Vehicle(AGV) to a fieldbus. In this paper, the IEEE 802.11 wireless LAN is used to extend a Profibus-DP network for the mobile devices. In order to integrate these two networks, a protocol converter is developed with two process(i.e., master process of Profibus-DP and virtual master process of IEEE 802.11) and an transmission buffer. Futhermore, a virtual polling algorithm is developed at the protocol conveter in order to satisfy real-time requirements on data communication.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.1
• /
• pp.47-57
• /
• 2002

In this paper, a wavelength converter for RZ data which can controls XPM in SOA by using polarization controller within optical fiber loop mirror is proposed and demonstrated. The proposed structure needs only one polarization dependent SOA for implementation compared to previous XPM ones and makes the cost down. And it provides wavelength converted signals with non-inverted and inverted pattern into outputs respectively.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.305-312
• /
• 2003

Recently, with a progressive development of hardware of computer, the internet and network technology, the environment of construction varies rapidly due to increase the complex form in structure shape and system. With variations, the CAD system for design and products also varies from 2D system to 3D system. This study mainly deals with the methodology of automatic connection design of 3D CAD system, steel connection system (XSteel) using macro. First, using design program in the steel connection system, Xsteel, the joint connection macro will be made up and established the detail classes of design. The next, Database Program (Converter Program) related to the general structural analysis program (MIDAS) and the steel connection program (Xsteel) is constructed for data interface between two programs. From this study, if the merits of 3D CAD system and converter program are utilized well, it is expected that the time needed in modeling and the amounts due to material loses decrease gradually.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.3
• /
• pp.10-17
• /
• 1995

this thesis proposes a new echo canceller that can be used in a fulll-duplex digital subscriber loopmodem. The modem suffers from nonlinear distortion such as transmitted pulse asymmetry, saturation in transformers, and nonlinearity of data converters. The proposed nonlinear echo canceller can compensate the nolinear distortion by using a nonlinear digital filter based on canonical pieceewise-linear (CPWL) function. Numerical results based on computer simulation are given in this paper. It is shown that the convergence characteristics depend on the initial values of weights of linear filters with absoluters and that the nonlinearity in digital-to-analog(D/A) converter can be compensated by a relatively small number linear filters with absoluters. It is also shown that the proposed algorithm has a faster convergence rate in comparison with Voterra algorithm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.352-353
• /
• 2013

본 연구에서는 12bit 1MSps 연속 근사화 아날로그-디지털 변환기(Analog to Digital Converter : ADC)를 설계하였다. 설계된 아날로그-디지털 변환기는 0.18um 1Metal 6Poly CMOS 공정을 이용하였고, Cadence tool을 이용하여 시뮬레이션 및 레이아웃 하였다. 시뮬레이션 결과 1.8V의 공급전압에서 전력 소모는 6mW였고, 입력 신호의 주파수가 100kHz 일 때, SNDR은 69.53dB, 유효 비트수는 11.26bit의 결과를 보였다.