• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.140-145
• /
• 2002

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal (PES) is becoming smaller and smaller. A substantial portion of the PES is caused by disk vibration. This can be reduced by using a head gimbal assemblies (HGAs) that do not confine the slider movement to the vertical direction to disks, but allow movement to the radial direction of disks with respect to disk vibration. Several types of HGAs are proposed for such radial motion of the slider. Experimental results show that the PES levels are reduced by the proposed HGA-design concepts.

• The Journal of Korea Robotics Society
• /
• v.5 no.4
• /
• pp.349-358
• /
• 2010

We presents a dynamic modeling of 4-wheel 2-DOF. WMR. The classic dynamic model utilizes a greatly simplified wheel motion representation and using of a simplified dynamic model confronts with a problem for accurate position control of wheeled mobile robot. In this paper, we treats the dynamic model for describes relationship between the wheel actuator force/torque and WMR motion through the use of Newton's equilibrium laws. To calculate the WMR position in real time, we introduced the Dead-Reckoning algorithms and the simulation result show that the proposed dynamic model is useful. We can be easily extend the proposed WMR model to mobile robot of similar type and this type of methodology is useful to analyze, design and control any kinds of rolling robots.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.11
• /
• pp.936-942
• /
• 2005

Recently the exoskeletal power assistive equipment which is a kind of wearable robot has been widely developed to help the human body motion. For the elderly people and patients, however, some limits exist due to the weight and volume of the equipments. As a feasible solution, a tendon-driven exoskeletal power assistive device fur the lower body, and caster walker are proposed in this research. Since the caster walker carries the heavy items, the weight and volume of the wearable exoskeleton are minimized. The key control is used to generate the joint torque required to assist motions such as sitting, standing and walking. Experiments were performed for several motions and the EMG sensors were used to measure the magnitude of assistance. When the motion of sitting down and standing up was compared with and without wearing the proposed device, the $25\%$ assistance was acquired.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.32.2-32
• /
• 2001

We have developed the power assistive leg called HAL (Hybrid Assistive Leg) which provide the walking aid for walking disorder persons or aged persons without nursing person. We developed HAL-3 by considering some problems of HAL-1,2 which had developed previously. The mechanism of HAL-3 actuator could be simplified and sophisticated by using the harmonic drive. As the control signal of HAL-3 EMG signal was used. We proposed a calibration method to identify parameters which relates the EMG to joint torque by using HAL-3. We could obtain suitable torque estimated by EMG and realize power assist in walking according to the intention of the operator To the remove discomfort for quick motion power assist, the feedforward controller was installed at the beginning of motion ...

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10b
• /
• pp.1006-1013
• /
• 1988

We have shown how unstructured modeling was used to derive a general stability condition in Part 1. In Part 2, we focus on the particular dynamics (structures modeling) of the robot manipulator and environment. Using rigid body dynamics, the stability condition for the direct drive robots has been achieved in terms of the Jacobian and robot tracking controller. Combining the structured and unstructured modeling, a stability condition for a particular application can be obtained. This approach has been used to analyze compliant motion on the University of Minnesota robot using a feedforward torque controller. We have obtained a stability condition for this application. Through both simulation and experiment, the sufficiency of this condition has been demonstrated. For a sufficient stability condition, recall that if the condition is satisfied, then the stability is guaranteed; however, if the condition is violated, no conclusion can be made.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.406-409
• /
• 1997

An economical 4-axis CNC controller employing step motors is designed and implemented in this paper. By using the inherent ability of holding position of the motor, the CNC controller uses open-loop control for removing trajectory error and for a simple hardware. Each drive of axis has an 8-bit microprocessor 89C52 and a PC controls the axes and pendant by means of RS232C serial communication. Backlash is also compensated at the axis controller. While compensating the backlash, the feed rate becomes zero in order to minimize trajectory error. The trajectories of 16ms interval are computed on PC and are sent to motor drives. In the drives, the trajectories are linearly interpolated for 2ms interval. The developed CNC does not require add-on specific motion card on PC. From the experimental results, the validity of the CNC controller based on step motor is proved.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.2
• /
• pp.18-28
• /
• 2001

Super computers has been utilized to carry out vehicle dynamics in real time. This research propose an implicit integra-tion method for vehicle state variables. Newton chord method is empolyed to solve the equations of motion and con-straints. The equations of motion and constraints are formulated such that the Jacobian matrix for Newton chord method is needed to be computed only once for a dynamic analysis. Numerical experiments showed that the Jacobian matrix generat-ed at the initial time could have been utilized for the Newton chord iterations throughout simulations under various driving conditions. Convergence analysis of Newton chord method with the proposed Jacobian updating method is carried out. The proposed algorithm yielded accurate solutions for a prototype vehicle multibody model in realtime on a 400 MHz PC compatible.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1513-1520
• /
• 2000

Complex modal testing method for rotating disks with support motion is introduced which handles the pairs of two point excitation and responses of the disk as complex input and output, respectively. This method utilizes the directivity information and the separation over the rotational speed of forward and backward traveling wave modes or bending coupled modes in the directional frequency response functions(dFRFs). This method synthesizes the normal/reverse dFRFs and complex wave dFRF, which were originally applied to rotating shaft and rotating disk, respectively, and is applied to complex system with dynamically coupled rotating disks and shaft. Experiments with a commercial hard disk drive spindle system demonstrate the validity of this method.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.371-376
• /
• 1999

Stick-slip friction is present to some degree in almost all actuators and mechanisms and is often responsible for performance limitations. Simulation of stick-slip friction is difficult because of strongly nonlinear behavior in the vicinity of zero velocity. A straightforward method for representing and simulating friction effects is presented. True zero velocity sticking is represented without equation reformulation or the introduction of numerical stiffness problems. Stick-slip motion is investigated experimentally, and the fundamental characteristics of the stick-slip motion are clarified. Based on these experimental results, the characteristics of static in the period of stick and kinetic friction in the period of slip are studied concretely so as to clarify the stick-slip process.

• Journal of Drive and Control
• /
• v.10 no.3
• /
• pp.21-26
• /
• 2013

This paper presents a robust motion tracking control of a cylinder-toggle servomechanism for injection molding machines. Virtual design model has been developed for a five-point type toggle mechanism. A sliding function is defined and combined with PID control to accommodate mismatches between the real plant and the linear model used. From tracking control simulations, it is shown that significant reduction in position tracking error is achieved with clamping force build-up through the use of proposed control scheme.