• IE interfaces
• /
• v.25 no.2
• /
• pp.178-186
• /
• 2012

The DRAM module is an important part of servers, workstations and personal computer. Its malfunction causes a lot of damage on customer system. Therefore, customers demand the highest quality products. The company applies DRAM module Outgoing Quality Assurance Inspection(OQA) to secures the highest quality. It is the key process to decides shipment of products through sample inspection method with customer oriented tests. High fraction of defectives entering to OQA causes inevitable high quality cost. This article proposes the application of ensemble learning to classify the lot status to minimize the ratio of wrong decision in OQA, observing a potential in reducing the wrong decision.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.5
• /
• pp.737-748
• /
• 1995

In this paper, we studyed the variables in the design of multichip memory modules with 4M$\times$1bit DRAM chips to construct high capacity and high speed memory modules. The configuration of the module was 8 bit, 16 bit, and 32 bit DRAM modules with employing 0.6 W, 70 nsec 4M$\times$1 bit DRAM chips. We optimized routing area and wiring density by performing the routing experiment with the variables of the chip allocation, module I/O terminal, the number of wiring, and the number of mounting side of the chips. The multichip module was designed to be able to accept MCM-L techiques and low cost PCB materials. The module routing experiment showed that it was an efficient way to align chip I/O terminals and module I/O terminals in parallel when mounting bare chips, and in perpendicular when mounting packaged chips, to set module I/O terminals in two sides, to use double sided substrates, and to allocate chips in a row. The efficient number of wiring layer was 4 layers when designing single sided bare chip mounting modules and 6 layers when constructing double sided bare chip mounting modules whereas the number of wiring layer was 3 layers when using single sided packaged chip mounting substrates and 5 layers when constructing double sided packaged chip mounting substrates. The most efficient configuration was to mount bare chips on doubled substrates and also to increase the number of mounting chips. The fabrication of memory multichip module showed that the modules with bare chips can be reduced to a half in volume and one third in weight comparing to the module with packaged chips. The signal propagation delay time on module substrate was reduced to 0.5-1 nsec.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.1 no.1
• /
• pp.31-39
• /
• 2001

W polymetal gate technology for giga bit DRAM are presented. Key module processes for polymetal gate are studied in detail. $W/WN_x/poly-silicon$ adopted for a word line of 256Mbit DRAM has good gate oxide integrity and junction leakage characteristics through full integration, which is comparable to those of conventional $WSi_x$/Poly-silicon gate process. These results undoubtedly show that $W/WN_x/poly-silicon$ is the strongest candidate as a word line for Giga bit DRAM.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.3
• /
• pp.49-60
• /
• 2002

A systematic design approach for Power distribution network (PDN) is presented aiming at applications to DRAM module designs. Three main stages are comprised in this design approach: modeling and simulation of a PDN based on a two-dimensional transmission line structure employing a partial element equivalent circuit (PEEC); verification of the simulation results through comparison to measured values; and design space scanning with PDN parameters. Impedance characteristics for do-coupling capacitors are analyzed to devise an effective way to stabilize power and ground plane Performance within a target level of disturbances. Self-impedance and transfer-impedance are studied in terms of distance between circuit features and the size of do-coupling capacitors. A simple equation has been derived to find the do-coupling capacitance values yielding impedance lower than design target, and thereby reducing the overall computation time. The effectiveness of the design methodology has been demonstrated using a DRAM module with discrete do-coupling capacitors and a strip structure.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.4
• /
• pp.73-76
• /
• 2010

A two-facet approach was used to investigate the parametric performance of functional high-speed DDR3 (Double Data Rate) DRAM (Dynamic Random Access Memory) die placed in different types of BGA (Ball Grid Array) packages: wire-bonded BGA (FBGA, Fine Ball Grid Array), flip-chip (FCBGA) and lead-bonded $microBGA^{(R)}$. In the first section, packaged live DDR3 die were tested using automatic test equipment using high-resolution shmoo plots. It was found that the best timing and voltage margin was obtained using the lead-bonded microBGA, followed by the wire-bonded FBGA with the FCBGA exhibiting the worst performance of the three types tested. In particular the flip-chip packaged devices exhibited reduced operating voltage margin. In the second part of this work a test system was designed and constructed to mimic the electrical environment of the data bus in a PC's CPU-Memory subsystem that used a single DIMM (Dual In Line Memory Module) socket in point-to-point and point-to-two-point configurations. The emulation system was used to examine signal integrity for system-level operation at speeds in excess of 6 Gb/pin/sec in order to assess the frequency extensibility of the signal-carrying path of the microBGA considered for future high-speed DRAM packaging. The analyzed signal path was driven from either end of the data bus by a GaAs laser driver capable of operation beyond 10 GHz. Eye diagrams were measured using a high speed sampling oscilloscope with a pulse generator providing a pseudo-random bit sequence stimulus for the laser drivers. The memory controller was emulated using a circuit implemented on a BGA interposer employing the laser driver while the active DRAM was modeled using the same type of laser driver mounted to the DIMM module. A custom silicon loading die was designed and fabricated and placed into the microBGA packages that were attached to an instrumented DIMM module. It was found that 6.6 Gb/sec/pin operation appears feasible in both point to point and point to two point configurations when the input capacitance is limited to 2pF.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.1
• /
• pp.108-114
• /
• 2004

In this paper we propose the boot system using CF memory card and study the system implementation method. The system that is proposed in this paper basically consist of high performance microprocessor, small amount of program memory and CF memory card. And added LCD module and touch panel for the user interface. This system use the CF memory card and DRAM instead of the Flash memory, so it can reduce the system cost. And system performance is increased because of the system program running in the DRAM.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.3
• /
• pp.118-123
• /
• 2020

In this paper, the design method of asynchronous nonvolatile memory module that can efficiently process and store large amounts of data without loss when the power turned off is proposed and implemented. PSRAM, which takes advantage of DRAM and SRAM, was used for data processing, and NAND flash memory was used for data storage and backup. The problem of a lot of signal interference due to the characteristics of memory devices was solved through PCB design using high-density integration technology. In addition, a boost circuit using the super capacitor of 0.47F was designed to supply sufficient power to the system during the time to back up data when the power is off. As a result, an asynchronous nonvolatile memory module was designed and implemented that guarantees reliability and stability and can semi-permanently store data for about 10 years. The proposed method solved the problem of frequent data loss in industrial sites and presented the possibility of commercialization by providing convenience to users and managers.

• Electronics and Telecommunications Trends
• /
• v.35 no.3
• /
• pp.55-65
• /
• 2020

With the development of nonvolatile memory technology, Intel has released the Optane datacenter persistent memory module (DCPMM) that can be deployed in the dual in-line memory module. The results of research and experiments on Optane DCPMMs are significantly different from the anticipated results in previous studies through emulation. The DCPMM can be used in two different modes, namely, memory mode (similar to volatile DRAM: Dynamic Random Access Memory) and app direct mode (similar to file storage). It has buffers in 256-byte granularity; this is four times the CPU (Central Processing Unit) cache line (i.e., 64 bytes). However, these properties are not easy to use correctly, and the incorrect use of these properties may result in performance degradation. Optane has the same characteristics of DRAM and storage devices. To take advantage of the performance characteristics of this device, operating systems and applications require new approaches. However, this change in computing environments will require a significant number of researches in the future.

• Journal of Advanced Navigation Technology
• /
• v.15 no.6
• /
• pp.1104-1110
• /
• 2011

The conventional semiconductor equipment has adopted SRAM module as the test pattern memory, which has a simple design and does not require refreshing. However, SRAM has its disadvantages as it takes up more space as its capacity becomes larger, making it difficult to meet the requirements of large memories and compact size. if DRAM is adopted as the semiconductor inspection equipment, it takes up less space and costs less than SRAM. However, DRAM is also disadvantageous because it requires the memory cell refresh, which is not suitable for the semiconductor examination equipments that require correct timing. Therefore, In this paper, we will proposed an algorithm for punctuality guarantee of memory-free inspection equipment using DDR2 SDRAM. And we will Developed memory controller using punctuality guarantee algorithm. As the results, show that when we adopt the DDR2 SDRAM, we can get the benefits of saving 13.5 times and 5.3 times in cost and space, respectively, compared to the SRAM.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.4
• /
• pp.1-1
• /
• 2001

본 논문에서는 μspring 패키지의 구조와 제조공정을 소개하고, 전기적 특성을 μBGA와 비교 분석한 결과를 제시하였다. μBGA에서와 같이 μSpring 패키지의 연결선 인덕턴스 값은 기존의 TSOP 패키지의 반 이하로서 월등한 고속 신호 전달 특성을 제공하게 된다. 또한 μSpring CSP 패키지의 경우 가장 열악한 substrate trace를 가진 핀에서도 2.9nH로 평가되어, Rambus DRAM module의 인덕턴스 규격 상한 값 4nH에 비하여, 약 25% 정도의 margin을 제공한다. μSpring CSP패키지는 μBGA의 약 50%의 제조 비용으로서 μBGA가 만족시키지 못하는 JEDEC Level 1 규격을 충족시킬 뿐만 아니라, thermal cycle 1000회를 통과하는 높은 신뢰성을 제공하여 강력한 경쟁력을 가진다.