• 산업기술연구
• /
• 제21권B호
• /
• pp.117-123
• /
• 2001

In a modern control field, a control engineer who has theoretical backgrounds with some practical knowledge is demanded. That is to say, an engineer who can understand and operate the various parts such as modeling, simulation, system analysis, signal processing, statistics, and hardware is required. In order to prove the theoretical backgrounds and operate various hardwares, a lot of experimental devices for students are designed in universities. Since the conventional experimental devices are manufactured abroad and the prices of the devices are too high, it is difficult to have. If a low cost experimental device can be developed, it will be very useful for a control engineering education. In Ibis paper, an experimental rig which has two control inputs and three sensor outputs to control the end point of a flexible beam is designed and manufactured. This rig can be used for a control field education.

• 대한기계학회논문집A
• /
• 제24권4호
• /
• pp.874-880
• /
• 2000

In this paper, a DC potential drop measurement system was used to find the position of the flaw on a simple thin plate. Four-point probe test was evaluated and used for this study. In the four-point probe test, the more distance between current pins provides the more measurable scope, the less voltage difference, and the more voltage difference rate. In the other hand, the more distance between voltage pins provides the less voltage difference and the less voltage difference rate. An optimized four-point probe was applied to measure the relation between voltage and the relative position of flaw to the probe. The Maxwell 21) simulator was used to analyze the electromagnetic field, and it showed that the analytical result was similar to the experimental result within 11.4% maximum error.

• Progress in Superconductivity
• /
• 제5권1호
• /
• pp.21-25
• /
• 2003

We have designed and simulated an 1-bit ALU (Arithmetic Logic Unit) by using a half adder. An ALU is the part of a computer processor that carries out arithmetic and logic operations on the operands in computer instruction words. The designed ALU had limited operation functions of OR, AND, XOR, and ADD. It had a pipeline structure. We constructed an 1-bit ALU by using only one half adder and three control switches. We designed the control switches in two ways, dc switch and NDRO (Non Destructive Read Out) switch. We used dc switches because they were simple to use. NDRO pulse switches were used because they can be easily controlled by control signals of SET and RESET and show fast response time. The simulation results showed that designed circuits operate correctly and the circuit minimum margins were ＋/-27%. In this work, we used simulation tools of XIC and WRSPICE. The circuit layouts were also performed. The circuits are being fabricated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.92-95
• /
• 2001

The dielectric breakdown of epoxy composites used for transformers was experimented and then its data were simulated by Weibull distribution probability. First of all, speaking of dielectric breakdown properties, the more hardener increased the stronger breakdown strength at low temperature because of cross-linked density by the virtue of ester radical. The breakdown strength of specimens with filler was lower than it of non-filler specimens because it is believed that the adding filler forms interface and charge is accumulated in it, therefore the molecular motility is raised and the electric field is concentrated. In the case of filled specimens with treating silane, the breakdown strength become much higher Finally, from the analysis of weibull distribution, it was confirmed that as the allowed breakdown probability was given by 0.1[%], the applied field value needed to be under 21.5 [Mv/cm].

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.196-197
• /
• 2006

In this study, low temperature sintering multilayer piezoelectric transformer for DC-DC converter were manufactured using (PbCaSr)Ti(MnSb)$O_3$ ceramics and thin their electrical properties were investigated according to the vanation of frequency and load resistance. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value m the vicinity of 1.3MHz and increased according to the increase of load resistance. When the output impedance coincided with the load resistance, the piezoelectric transformer showed the temperature rise of about $21^{\circ}C$ under the output power of 6W.

• Journal of Korean Vacuum Science & Technology
• /
• 제6권1호
• /
• pp.16-21
• /
• 2002

Ti-0 film is a kind of biocompatible surface materials. In this paper, a new method, glow discharge plasma oxidizing, has been used in synthesizing Ti-O gradient films on Ti6A14V substrates. The effects of ion bombardment and process parameters on the structures of titanium oxide layers have been investigated. The results demonstrate that DC glow plasma oxidizing is more efficient in preparation of dense, hard, and high adhesive Ti-O biomedical films on titanium and its alloys. Samples treated by this method show higher hardness values than by others. Especially, in the condition of hollow cathode discharge, the ion bombardment enhances ionization of oxygen, promotes the oxygen permeation and facilitates the formation of the oxide of low valence states of titanium.

• Journal of Power Electronics
• /
• 제10권1호
• /
• pp.21-26
• /
• 2010

The most important feature of the one-cycle control method is its excellent ability in line disturbance rejection. However, when it is used as a controller in dc-dc converters, it has an undesirable transient response. The voltage overshoot at the transient time, which usually exists in one-cycle controlled converters, is unwanted in many applications and it is sometimes hazardous. In this paper, it is shown that the combination of a one-cycle controller with a current mode controller, can improve the transient response and consequently the overshoot can be controlled. Therefore, the combined controller has the excellent line disturbance rejection of a one-cycle controller and the output current limiting capability of current mode controllers. Because in this scheme a one-cycle controller is the master controller, the problem of instability of current mode control, will not happen. By simulation and a practical prototype, the capability of the method is shown.

• 조명전기설비학회논문지
• /
• 제16권4호
• /
• pp.15-21
• /
• 2002

본 논문에서는 동적 전류분담 인덕터를 이용한 ZVT 풀 브리지 DC/DC 컨버터의 병렬운전 특성을 해석하였다. 기존의 경우 CT(Current Transformer)를 사용하여 각 단위 컨버터 전류의 크기를 감지하여, 제어회로에서 각 컨버터에 균등한 전류 배분을 하는 방법을 사용하였으나, 본 연구에서는 동적 전류분담 인덕터를 사용함으로써 병렬운전하는 두 대의 풀 브리지 컨버터의 전류분배를 위한 제어회로를 비교적 단순하게 하였다. 동시에 ZVT회로를 이용하여 컨버터의 효율을 향상시켰으며 스위칭소자로서 IGBT를 사용하여 2[㎾]급 시작품을 제작, 50[KHz]에서 실험하였다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.49-52
• /
• 2008

현재 산업사회의 발달과 더불어 신뢰성 높은 양질의 전기에너지와 운전 및 보수의 간편화, 계통운용의 신뢰성의 확보가 요구되고 있다. 또한 $SF_6$을 대체할 친환경적인 절연매체의 개발이 절실히 요구되고 있다. 이에 본 연구는 모의 GIS내 친환경적인 절연재료인 질소($N_2$)와 산소($O_2$)의 혼합가스($N_2:O_2=79:21$, $N_2:O_2=60:40$, $N_2:O_2=40:60$)의 기본적인 절연특성을 구명함으로서 각종 전력응용 설비의 절연매체로 사용가능함을 구명하고저 한다.

• Journal of the Korean Wood Science and Technology
• /
• 제21권4호
• /
• pp.29-34
• /
• 1993

This study was carried out to estimate price and domestic consumption functions of chestnut using time series data for the period 1970~1989. Using a regression analysis method, price and domestic consumption functions of chestnut in Korea are estimated. The result of this study reveals that the optimum function of price for chestnut is PR= -249.33965 + 163532.56817 EX/POP-4.10177 PD+4.02877 DC+6056.98339 GDP/POP($R^2$=0.88207), and that optimum function of domestic consumption for chestnut is ln DC=14.97145+1.48279 ln PD/POP - 0.32853 ln GDP - 0.02337 ln PR - 0.12117 ln EX($R^2$=0.98689). On the ground that instability of prices make the income of producer and family finances of consumer unstable, the object of price-policy should be to stabilize price of chestnut in Korea.