• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.19-19
• /
• 2009

TiNxOy/TiNx multilayer thin films with a high resistance (~ k$Omega$) were deposited on SiO2/Si substrates at room temperature by sputtering. The TiNx thin films show island and smooth surface morphology in samples prepared by dc and rf magnetron sputtering, respectively. TiNxOy/TiNx multilayer has been developed to control temperature coefficient of resistance (TCR) by the incorporation of TiNx layer (positive TCR) inserted into TiNxOy layers(negative TCR). Electrical and structural properties of sputtered TiNxOy/TiNx multilayer films were investigated as a function of annealing temperature. In order to achieve a stable high resistivity, multilayer films were annealed at various temperatures in oxygen ambient. Samples annealed at 700 oC for 1 min exhibit a good TCR value and a stable high resistivity.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.587-591
• /
• 1998

AZO transparent conducting thin film were fabricated by DC magnetron sputtering using the Zn: Al (2% aluminu contained ) alloy target with inducing microwave to the plasma, and the effect of microwave was studied. The optical transmittance, the resistivity and dynamic deposition rate at the applied voltage to target of 420 V was 50~70%, $ 5.5{\times}10^{-3}{\Omega}$cm and 6,000 $\AA\textrm{mm}^2$/J, respectively. After annealing AZO coated glass at $400^{\circ}C$ for 30 minutes, the light transmittance was increased to 80% and electrical conductivity was also increased two times, reached to resistivity of $2.0{\times}10^{-3}{\Omega}$cm.

• Journal of Sensor Science and Technology
• /
• v.13 no.4
• /
• pp.303-308
• /
• 2004

This paper descibes on the characteristics of Ta-N(tantalum nitride) ceramic thin-film strain gauges which were deposited on Si substrates by DC reactive magnetron sputtering in an argon-nitrogen atmosphere (Ar-$(4{\sim}16%)N_{2}$) for high-temperature applications. These films were annealed in $2{\times}10^{-6}$ Torr vacuum furnace at the range of $500{\sim}1000^{\circ}C$. Optimum deposition atmosphere and annealing temperature were determined at $900^{\circ}C$ for 1 hr. in 8% $N_{2}$ gas flow ratio. Under optimum formation conditions, the Ta-N thin-film for strain gauges was obtained a high-resistivity of $768.93{\mu}{\Omega}{\cdot}cm$, a low temperature coefficient of resistance (TCR) of -84 ppm/$^{\circ}C$ and a good longitudinal gauge factor (GF) of 4.12.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.4
• /
• pp.151-155
• /
• 2017

The ZTO single layer and ZTO/Ag/ZTO tri-layer films were deposited on glass substrates by using the radio frequency (RF) and direct current (DC) magnetron sputtering and then rapid thermal annealed (RTA) in a low pressure condition for 10 minutes at 150 and $300^{\circ}C$, respectively. As deposited tri-layer films show the 81.7% of visible transmittance and $4.88{\times}10^{-5}{\Omega}cm$ of electrical resistivity, while the films annealed at $300^{\circ}C$ show the increased visible transmittance of 82.8%. The electrical resistivity also decreased as low as $3.64{\times}10^{-5}{\Omega}cm$. From the observed results, it is concluded that rapid thermal annealing (RTA) is an attractive post-deposition process to optimize the opto-elecrtical properties of ZTO/Ag/ZTO tri-layer films for the various display applications.

• Bulletin of the Korean Space Science Society
• /
• 2008.10a
• /
• pp.37.3-37.3
• /
• 2008

STJ(Superconducting Tunnel Junction) technique offers next generation photon detectors exhibiting high energy resolution, high quantum efficiency and photon counting ability over the broad wavelength range from X-ray to NIR. We report the succcess in fabrication of Ta/Al-AlOx-Al/Ta and Nb/Al-AlOx-Al/Nb micro structure deposited on sapphire substrates using various techniques including UV photolithography, DC Sputtering, RIE, and PECVD technique. The characterization experiment was undertaken in an Adiabatic Demagnetization Refrigerator at an operating temperature below 50mK. The details of experimental investigations for electrical characterization of STJ of $20\sim80{\mu}m$ in side-lengths are discussed. The measured I-V curves were used to derive The detector performance indicators such as energy gap, energy resolution, normal resistance, normal resistivity, dynamic resistance, dynamic resistivity, and quality factor.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.340-351
• /
• 1995

Electrical, physical and optical properties of Aluminum(Al), Copper(Cu) thin films were investigated in order to establish the optimum sputtering parameters in Liquid Crystal Display (LCD) panel applications. DC-magnetron sputtered film on coming 7059 samples were fabricated with variations of deposition power densities, deposition pressures and substrate temperatures. Low resistivity films(AI;2.80 .mu..ohm.-cm, Cu:1.84 .mu..ohm-cm),which lower than the reported values, were obtained under sputtering parameters of power density(250W), substrate temperature(450-530.deg. C) and 5*10$\^$-3/ Torr deposition pressure. Expected columnar growth and stable grain growth of both films was observed through the Scanning Electron Microscope(SEM) micrographs. Dependency of the applicable defect-free film density upon depositon power and temperature was also characterized. Not too noticable variations in X-ray diffraction patterns were remarked under the alterations of sputtering parameters. High optical reflectivities of Al, Cu films, approximately 70-90 %, showed high degree of surface flatness.

• ETRI Journal
• /
• v.21 no.4
• /
• pp.1-8
• /
• 1999

Thick metal 0.8${\mu}m$ CMOS technology on high resistivity substrate(RF CMOS technology) is demonstrated for the L-band RF IC applications, and we successfully implemented it to the monolithic 900 MHz and 1.9 GHz CMOS LNAs for the first time. To enhance the performance of the RF circuits, MOSFET layout was optimized for high frequency operation and inductor quality was improved by modifying the technology. The fabricated 1.9 GHz LNA shows a gain of 15.2 dB and a NF of 2.8 dB at DC consumption current of 15mA that is an excellent noise performance compared with the offchip matched 1.9 GHz CMOS LNAs. The 900 MHz LNA shows a high gain of 19 dB and NF of 3.2 dB despite of the performance degradation due to the integrating of a 26 nH inductor for input match. The proposed RF CMOS technology is a compatibel process for analog CMOS ICs, and the monolithic LNAs employing the technology show a good and uniform RF performance in a five inch wafer.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.1
• /
• pp.11-16
• /
• 2001

CuNi alloy films are deposited by co-sputtering of dual targets (Cu and Ni, respectively). Effects of the co-sputtering conditions, such as powers applied to the targets, deposition pressures, and substrate temperatures, on the structural and electrical properties of deposited films are systematically investigated. The composition ratio of Ni/Cu is almost linearly decreased by increasing the DC power applied to the Cu target from 25.6 W to 69.7 W with the RF power applied to the Ni target unchanged(140 W). it is noted that the chamber pressure during deposition and the film thickness give rise to a change of the Ni/Cu ratio within the films deposited. The former may be due to a higher sputtering yield of Cu atom and the latter due to the re-sputtering phenomenon of Cu atoms on the surface of deposited film. The film deposited at higher pressures or at lower substrate temperatures have a smaller crystallite size, a higher electrical resistivity, and much more voids. This may be attributed to a lower surface mobility of sputtered atoms over the substrate.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.4
• /
• pp.493-500
• /
• 1996

AZO transparent conducting thin films were fabricated by reactive DC magnetron sputtering method using Zn metla target containing 2 wt% of Al, and electrical and optical properties were investigated after heattreatment. Electrical resistivity was reduced 50% and had reached $1{\times}10^{-3}~3.5{\times}10^{-4}\;{\Omega}cm$ by heat treatment. In the case of oxide AZO films, the resistivity of $10^{3}\;{\Omega}cm$ was also decreased to $2{\times}10^{-3}\;{\Omega}cm$ after heat treatment. The optical transmittance of AZO films deposited in the transition range was increased from 59.4 % to 77.4 % by $400^{\circ}C$, 30 min heat treatment.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.1
• /
• pp.23-27
• /
• 2003

Structural properties of Cu-Ni alloy films, such as preferred orientation, crystallite size, in-ter-planar spacing, cross-sectional morphology, and electrical resistivity, are investigated in terms of tar-get configurations that are used in the film deposition by means of magnetron co-sputtering. Two different target configurations are considered in this study: a dual-type configuration in which two separate tar-gets (Cu and Ni) and different bias types (RF and DC) are used and a Ni-on-Cu type configuration in which Ni chips are attached to a Cu target. The dual-type configuration appears to have some advantages over the Ni-on-Cu type regarding the accurate control of atomic composition of the deposited Cu-Ni alloy. However, the dual-type-produced film exhibits a porous and columnar structure, the relatively large internal stress, and the high electrical resistivity, which are mainly due to the relatively low mobility of adatoms. The affects of thermal treatment and deposition conditions on the structural and electrical properties of dual-type Cu-Ni films are also discussed.