• Korean Journal of Materials Research
• /
• v.28 no.10
• /
• pp.544-550
• /
• 2018

The passivation of AZ91D Mg alloys by plasma anodization requires deliberate choice of process parameters due to the presence of large amounts of structural defects. We study the dependence of pore formation, surface roughness and corrosion resistance on voltage by comparing the direct current (DC) mode and the pulse wave (pulse) mode in which anodization is performed. In the DC plasma anodization mode, the thickness of the electrolytic oxide film of the AZ91D alloy is uneven. In the pulse mode, the thickness is relatively uniform and the formed thin film has a three-layer structure. The pulse mode creates less roughness, uniform thickness and improved corrosion resistance. Thus, the change of power mode from DC to pulse at 150 V decreases the surface roughness (Ra) from $0.9{\mu}m$ to $0.1{\mu}m$ and increases the corrosion resistance in rating number (RN) from 5 to 9.5. Our study shows that an optimal oxide film can be obtained with a pulse voltage of 150 V, which produces an excellent coating on the AZ91D casting alloy.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.47.1-47.1
• /
• 2009

최근 환경과 에너지에 대한 관심이 증대됨에 따라 차체의 경량화를 위한 고합금계 알루미늄 합금의 연구가 활발히 진행되고 있다. 특히 5000계 알루미늄 합금은 비중이 낮을 뿐만 아니라 Mg의 첨가에 의해 높은 강도 및 성형성을 얻을 수 있기 때문에 자동차용 판재로 많은 주목을 받고 있다. 현재 사용되는 대부분의 알루미늄 합금판재는 DC주조법과 추가적인 압연공정으로 제조되기 때문에 경제성 문제와 낮은 냉각속도로 인한 금속학적인 문제를 갖는다. 그러나 DC주조법과는 달리 쌍롤 박판주조법은 용탕으로부터 직접 판재를 제조하기 때문에 경제적이며 효율적인 주조공정이다. 또한 냉각속도가 빠르기 때문에 비교적 주조편석이 적고 전반적인 미세조직이 균일하여 고합금계 알루미늄 합금 판재제조에 매우 유용하게 응용될 수 있다. 본 연구에서는 쌍롤 박판주조법으로 고합금계 알루미늄 합금 판재를제조하고, 제조된 합금의 열간압연 및 열처리 조건에 따른 기계적 특성을 비교 및 평가하였다. 또한 미세조직 및 집합조직을 분석함으로써 고합금계 알루미늄 합금 판재의 실용화 가능성을 평가하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.196-197
• /
• 2006

In this study, low temperature sintering multilayer piezoelectric transformer for DC-DC converter were manufactured using (PbCaSr)Ti(MnSb)$O_3$ ceramics and thin their electrical properties were investigated according to the vanation of frequency and load resistance. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value m the vicinity of 1.3MHz and increased according to the increase of load resistance. When the output impedance coincided with the load resistance, the piezoelectric transformer showed the temperature rise of about $21^{\circ}C$ under the output power of 6W.

• Journal of the Korean Magnetics Society
• /
• v.25 no.3
• /
• pp.67-73
• /
• 2015

This is a basic research for improving soft magnetic property of Fe based nano crystalline alloy powder core. The main study is done around characteristics of permeability, core loss, and DC bias depending on amount of insulation coating agent and particle size. First, $Fe_{73.5}Si_{13.5}B_9Nb_3Cu_1$ amorphous alloy ribbon was fabricated by using the planar flow casting (PFC) device. Then, heat treatment and ball milling were done to obtain alloy powder. The amount of polyether imide (PEI) added to it was varied by 0.5, 1.0, 2.0, 2.5 wt% to have compression molding into $16ton/cm^2$. After going through crystalline heat treatment, the made toroidal nano crystalline powder core ($OD12.7mm^*ID7.62mm^*H4.75mm$) had smaller permeability as amount of insulation coating agent decreases. However, it was found out that core loss and DC bias characteristics have been improved. The reason for this results were expected to be because green density of power core decreases as amorphous alloy powder particles become smaller as amount of alloy powder insulation coating agent increases, it was determined that 1 wt% of insulation coating agent is appropriate. Also, for powder core made based on alloy powder size with amount of insulation coating agent fixed at 1 wt%, effective permeability and core loss were outstanding as particle size became bigger. However, characteristics of DC bias became worse as applied DC field increases. This is expected to be due to insulation effect, residual pores, or molding density of powder core resulting from thickness of coating on surface of alloy powder.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.11
• /
• pp.948-952
• /
• 2007

In this study, a low temperature sintering multilayer piezoelectric transformer for a DC-DC converter was manufactured using $(Pb,Ca,Sr,)(Ti,Mn,Sb)O_3$ ceramics. Its electrical properties were investigated according to the variation in frequency and load resistance. The voltage step-up ratio of the multilayer piezoelectric transformer showed a maximum value at a resonant frequency of input part and increased with an increase of load resistance. The efficiency of the multilayer piezoelectric transformer showed the highest value at a load resistance of 17 $\Omega$. The output power was increased with increasing input voltage. Temperature increase of the multilayer piezoelectric transformer was increased with the increase of output power. At the load resistance of 17 $\Omega$, the multilayer piezoelectric transformer showed the temperature rises of about $20^{\circ}C$ at the output power of 18 W, and stable driving characteristics.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.441-447
• /
• 2001

A study on the TiN coating layer in small holes on the Purpose of die-casting dies application has been performed with a PACVD process. For the hole having diameter of 4 mm. the uniform TiN coating layer in the hole to the depth of 20 mm was achieved using DC pulsed power source. To understand the forming mechanism of TiN coating layer, plasma diagnosis on Ti, $N_{2}^{+}$ and A $r^{+}$ emissions was carried out during plasma coaling process by optical emirssion spectroscopy. When the duty ratio was equal or over 50%, the Peaks of Ti,$ N_{2}^{+}$ and A $r^{+}$ emission were obviously observed. While duty ratio was equal or under 28.6%, no peaks for Ti, $N_{2}^{+}$ and A $r^$ were observed and the formation of TiN coating layer was rarely observed. For the coating in 4 mm hole diameter, the coating layer with bipolar process was two times deeper than that with unipolar process.