• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.7
• /
• pp.945-951
• /
• 2013

This study evaluated the fatigue strength of the bogie frame of an urban maglev train through fatigue analysis, cumulative damage, and fatigue tests based on a proposed fatigue evaluation method. The results of FEM analysis in which various load combinations were adopted showed that all data were under the fatigue limit of a butt welded joint made of A6005 in a Goodman diagram. The cumulative fatigue damage was calculated at the highest level from a bolt connecting the area of the electromagnetic pole in the casting block; however, the total sum was evaluated as D=0.808 based on $1{\times}10^7$ cycles, which indicates that it did not exceed the failure criteria. In addition, the results of the fatigue testshowed that there was no crack at any position in the bogie frame, which corresponded to the results of fatigue analyses.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.1
• /
• pp.69-75
• /
• 2015

PURPOSE. To compare the shear bond strength of various veneering materials to grade II commercially pure titanium (CP-Ti). MATERIALS AND METHODS. Thirty specimens of CP-Ti disc with 9 mm diameter and 10 mm height were divided into three experimental groups. Each group was bonded to heat-polymerized acrylic resin (Lucitone 199), porcelain (Triceram), and indirect composite (Sinfony) with 7 mm diameter and 2 mm height. For the control group (n=10), Lucitone 199 were applied on type IV gold alloy castings. All samples were thermocycled for 5000 cycles in $5-55^{\circ}C$ water. The maximum shear bond strength (MPa) was measured with a Universal Testing Machine. After the shear bond strength test, the failure mode was assessed with an optic microscope and a scanning electron microscope. Statistical analysis was carried out with a Kruskal-Wallis Test and Mann-Whitney Test. RESULTS. The mean shear bond strength and standard deviations for experimental groups were as follows: Ti-Lucitone 199 ($12.11{\pm}4.44$ MPa); Ti-Triceram ($11.09{\pm}1.66$ MPa); Ti-Sinfony ($4.32{\pm}0.64$ MPa). All of these experimental groups showed lower shear bond strength than the control group ($16.14{\pm}1.89$ MPa). However, there was no statistically significant difference between the Ti-Lucitone 199 group and the control group, and the Ti-Lucitone 199 group and the Ti-Triceram group. Most of the failure patterns in all experimental groups were adhesive failures. CONCLUSION. The shear bond strength of veneering materials such as heat-polymerized acrylic resin, porcelain, and indirect composite to CP-Ti was compatible to that of heatpolymerized acrylic resin to cast gold alloy.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.4
• /
• pp.278-284
• /
• 2014

PURPOSE. There is insufficient data regarding the durability of porcelain laminate veneers bonded to existing composite fillings. The aim of the present study was to evaluate the fracture resistance and microleakage of porcelain laminate veneers bonded to teeth with existing composite fillings. MATERIALS AND METHODS. Thirty maxillary central incisors were divided into three groups (for each group, n=10): intact teeth (NP), teeth with class III composite fillings (C3) and teeth with class IV cavities (C4). Porcelain laminate veneers were made using IPS-Empress ceramic and bonded with Panavia F2 resin cement. The microleakage of all of the specimens was tested before and after cyclic loading ($1{\times}10^6$ cycles, 1.2 Hz). The fracture resistance values (N) were measured using a universal testing machine, and the mode of failure was also examined. The statistical analyses were performed using one-way ANOVA and Tukey post hoc tests (${\alpha}=.05$). RESULTS. There was a significant difference in the mean microleakage of group C4 compared with group NT (P=.013). There was no significant difference in the fracture loads among the groups. CONCLUSION. The microleakage and failure loads of porcelain laminate veneers bonded to intact teeth and teeth with standard class III composite fillings were not significantly different.

• Radiation Oncology Journal
• /
• v.9 no.2
• /
• pp.249-252
• /
• 1991

A Retrospective study to analyze the failure pattern in locally advanced stomach cancer, treated with radical surgery and post-op chemotherapy was perfomed. Among 107 patients who underwent radical gastrectomy in Asan Medical Center between June 1989 and August 1990. there were 20 stage II(T2NO, T2N1) and 87 stage III(T3N1, T3N2) and 91 patients were eligible for study. 57 patients treated with 6 cycles of postop adjuvant chemotherapy. Among 57 patients treated with postop adjuvant chemotherapy, local failure occurred in $21\%$ and distant failure in $12\%$. Among 34 patients who were not treated with postop chemotherapy, local failure occurred in $24\%$ and distant failure in $26\%$. Among 29 failures including 13 locoregional, 9 distant metastasis and 7 locoregional and distant metastasis, 11 cases recurred in the anastomotic site, 3 in the gastric bed,7 in the regional lymph nodes and peritoneal seeding occurred in 6 cases. The true incidences of gastric bed, nodal and peritoneal failures may be higher in the longer follow-up or reoperative or autopsy series. Our data sugest that postop chemocherapy is beneficial by reducing distant failure rate. Our data suggest that postop chemocherapy is beneficial by reducing distant failure rate. Postop adjuvant locoregional radiotherapy in addition to the systemic adjuvant therapy may reduce the local failure rate and potentially benefit in at least $20\%$ of patients who developed the local failure only.

• Journal of Advanced Navigation Technology
• /
• v.18 no.4
• /
• pp.381-386
• /
• 2014

In order to investigate the effect of contact load, which is one of the fretting corrosion factors affecting the electric connector, a coupled fretting corrosion specimens were prepared using a tin-plated brass coupon with a thickness of $3{\mu}m$. Electric resistance of the contact was measured during the fretting corrosion test period. There was increase in resistance with fretting cycles. The change in resistance can be classified by 3 stages. The first stage exhibited low and stable resistance. Second stage showed steady increment of the resistance and third stage showed very high and intermittent resistance. The relationship between the failure cycle (Nf) and contact force (P) can be drawn as; It is possible to draw the prediction equation for the failure cycle of the electric connector corresponding to the very high and intermittent resistance under various environment conditions through the fretting tests under various conditions such as load, displacement, temperature.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.4
• /
• pp.237-242
• /
• 1993

The fatigue behaviors of mechanically alloyed Al-4Mg alloys dispersed with either $Al_2O_3$ or $MgAl_2O_4$ oxide particles were investigated. This study maily concerned with the role of coherency of dispersed particles with the matrix on the fatigue behavior of the alloys. The $MgAl_2O_4$ which has a spinel structure with the lattice parameter of exactly the twice of Al showed the habit relation with the matrix. The mechanically alloyed Al-4Mg alloys showed stable stress responses with fatigue cycles from start to failure regadless of strain amplitudes and of existence of dispersoids. The Al-4Mg alloy dispersed with $MgAl_2O_4$ showed not only the better static mechanical properties but also the better low cycle fatigue resistance than that with $Al_2O_3$, i.e., much higher plastic strain energy dissipated to failure, at low strain amplitude. However, this alloy showed inferior fatigue resistance to that dispersed with $Al_2O_3$ or that without dispersion at high strain amplitude. These results imply that $MgAl_2O_4$ may promote lowering the stacking fault energy of the alloy inherited from the coherency with the matrix so that dislocations shuttle back and forth on the same slip plane without cross slipping to other planes during fatigue at low strain amplitude resulting in long fatigue life.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.1
• /
• pp.63-70
• /
• 2009

Failure modes result in fracture or tearing, which may cause deterioration of resistance and reduction of inelastic deformation capacity. The potential failure modes for Special Concentrically Braced Frames (SCBFs) include fracture or tearing of the brace, net section fracture of the brace or gusset plate, fracture of the gusset plate welds, shear fracture of the bolts, block shear, excessive bolt bearing deformation, and buckling of the gusset plate. HSS tubular braces are commonly used in SCBFs, and net section fracture of the tubular brace may also occur through the brace net section at the end of the slot cut into the tube to slip over the gusset plate. This failure mode is categorized as a tension failure mode, and may cause dramatic loss of resistance and brittle behavior. Net section reinforcement is required according to AISC design specifications (AISC 2001). In this paper, the need to reinforce the net section area was discussed. Initially, the results of the net section fracture tests done by the University of California in Berkeley were presented with the modeling of these tests using FE models. To investigate the possibility of net section fracture in an actual frame, the slot end hole model was adapted to the frame FE model, and alternate near-fault histories were applied with tension-dominated cycles, since previous analyses showed that loading history was the most critical factor in net section fracture. The need for this reinforcement (cover plate) and the tension-dominated near-fault history were investigated.

• Clinical and Experimental Reproductive Medicine
• /
• v.19 no.1
• /
• pp.31-39
• /
• 1992

By means of the results of In vitro fertilization(IVF) of supernumerary oocytes, the possibility of predicting a pregnancy outcome following gamete intrafallopian transfer(GIFT) and the prognostic implications for future pregnancy were evaluated in 46 GIFT cycles excluding simultaneous program of GIFT and IVF from February, 1989 to July, 1991. IVF of supernumerary oocytes were identified in 21 cycles, but not in remaining 25 cycles. There was no significant difference in age, duration and etiologic factors of infertility, and serum levels of FSH, LH and $E_2$ on MCD #3 and $E_2$ on the day of hCG injection between fertilized(N=21) and unfertilized group(N=25). The number of oocytes retrieved was similar in both groups. The number of supernumerary oocytes available for IVF after transfer was $5.43{pm}2.95$ ranging from 2 to 12. The prenancy rate in fertilized group, 33.3%(7/21), was higher without statistical significance, compared with 8.0%(2/25) in unfertilized group. Using IVF of supernumerary oocytes as a test of pregnancy following GIFT, sensitivity was 77.8 %; specificity, 61.2%; positive predictive value(PPV), 33.3%; negative predictive value(NPV), 92%. The fertilization rate of supernumerary oocytes in pregnant group, $86.4{\pm}22.8%$ was significantly higher compared with $56.1{\pm}20.2%$ in nonpregnant group. In cases with fertilization rate ${\geq}80%$, pregnancy was expected with PPV of 85.7%. In conclusion, IVF of supernumerary oocytes in GIFT program can be a profitable method as a prognostic indicator of pregnancy following GIFT. More aggressive diagnostic and therapeutic measures should be performed in cases with failure in IVF of supernumerary oocytes.

• Radiation Oncology Journal
• /
• v.23 no.2
• /
• pp.71-77
• /
• 2005

Purpose: This retrospective study was conduced to analyze the treatment results and to evaluate the prognostic factors affecting the survival of nasopharyngeal carcinoma patients. Materials and Methods: From 1987 to 2002, we analyzed 43 patients who had nasopharyngeal carcinomas that were histologically confirmed and who had also completed the planned radiation therapy course at Keimyung University Dongsan Medical Center According to the 6th edition of American Joint Committee on Cancer staging system, 12 patients ($27.9\%$) were at Stage 11, 13 ($30.2\%$) were at Stage III and 18 ($41.9\%$) were at Stage IV Histopathologically, there were 15 ($34.9\%$) squamous cell carcinomas, 8 ($18.5\%$) nonkeratinizing carcinomas, 17 ($39.5\%$) undifferentiated carcinomas, and 3 ($7.0\%$) lymphoepitheliomas. Among the total 43 patients, 31 patients ($72.1\%$) were treated with only radiation therapy. Neoadjuvant chemotherapy was peformed on 7 patients ($16.3\%$) and concurrent chemoradiotherapy was performed on S patients ($11.6\%$). Cisplatin and 5-Fluorouracil were administered to 11 patients for 4 cycles, and Cisplatin and Taxotere were administered to 1 patient for 6 cycles. The range of the total radiation dose delivered to the primary tumor was from 61.2 to 84 Gy (median 70.4 Gy), The follow-up period ranged from 2 to 197 months with median follow-up of 84 months. Results: The local control rate at 6 months after radiation therapy was $90.7\%$. The five year overall survival and disease free survival rates were $50.7\%$ and $48.9\%$, respectively. On the multivariate analysis, the age, T-stage ($T_{1-3}\;vs\;T_4$), N-stage and AJCC stage were the statistically significant prognostic factors affecting survival (p<0.05). The patterns of failure were as follows: local failure only in 3 patients ($7.0\%$), local and systemic failure in 1 patient ($2.3\%$), and distant metastasis only in 11 patients ($25.6\%$). Conclusion: The prognostic factors affecting the outcome of nasopharyngeal carcinoma were age, T-stage (7$T_{1-3}\;vs\;T_4$), N-stage and stage. Because systemic metastasis was the main failure pattern noted for nasopharyngeal carcinoma, systemic chemotherapy is needed to decrease the rate of distant metastasis for nasopharyngeal carcinoma. In audition, research for more effective chemotherapeutical regimens and schedules is also needed.

• Journal of Digestive Cancer Research
• /
• v.2 no.1
• /
• pp.28-31
• /
• 2014

Pancreatic cancer is a highly aggressive cancer with poor prognosis. Although, gemcitabine is the current standard regimen as first-line chemotherapy for advanced pancreatic cancer, effective regimens of second-line chemotherapy after gemcitabine failure have not been established yet. We report a case of gemcitabine refractory pancreatic cancer treated with second-line chemotherapy with FOLFIRINOX regimen. A 57-year-old-woman visited our hospital for pancreatic body mass detected by computed tomography (CT). The patient underwent distal pancreatectomy and splenectomy and the pathologic results after surgery demonstrated adenocarcinoma. Follow-up was performed after surgery and CT and positron emission tomography (PET) 4 months after surgery revealed multiple hepatic metastases. The patient underwent first-line chemotherapy with gemcitabine and erlotinib for recurred pancreatic cancer. However, CT after 7 cycles of the chemotherapy showed the progression of multiple hepatic metastases and switch to second-line chemotherapy with FOLFIRINOX was initiated. CT after 16 cycles of the FOLFIRINOX showed the complete remission of multiple hepatic metastases. The patient was admitted for infective endocarditis with septic pneumonia 17 months after the initiation of FOLFIRINOX. However, the patients died from the progression of septic embolism and acute respiratory distress syndrome.