• Journal of the Korean Institute of Gas
• /
• v.15 no.3
• /
• pp.47-52
• /
• 2011

The purpose of this paper analyzes and studies to seek the failure examples of electronic control actuators for engine in liquified petroleum gas vehicle. The first, it was verified phenomenon for intial starting damage and no-acceleration of engine because of occasionally fuel feeding interception by clogged of emergency cutting solenoid valve filter. The second, the contact resistance produced in the connecting part of engine control relay because of no fully surface contacting by processes and assembly badness. It was displayed phenomenon of re-starting badness. The actuator that idle speed control system was sticked inside because of intake-air decreasing by carbon deposit. As a result, it was verified the phenomenon of disharmony that repeated up and down the engine revolution.

• Geomechanics and Engineering
• /
• v.19 no.2
• /
• pp.153-165
• /
• 2019

A case study of monitoring and analysis of surface settlement induced by tunneling of Tabriz metro line 2 (TML2) is presented in this paper. The TML2 single tunnel has been excavated using earth pressure balanced TBM with a cutting-wheel diameter of 9.49 m since 2015. Presented measurements of surface settlements, were collected during the construction of western part of the project (between west depot and S02 station) where the tunnel was being excavated in sand and silt, below the water table and at an average axis depth of about 16 m. Settlement readings were back-analyzed using Gaussian formula, both in longitudinal and transversal directions, in order to estimate volume loss and settlement trough width factor. In addition to settlements, face support and tail grouting pressures were monitored, providing a comprehensive description of the EPB performance. Using the gap model, volume loss prediction was carried out. Also, COB empirical method for determination of the face pressure was employed in order to compare with field monitored data. Likewise, FE simulation was used in various sections employing the code Simulia ABAQUS, to investigate the efficiency of numerical modelling for the estimating of the tunneling induced-surface settlements under such a geotechnical condition. In this regard, the main aspects of a mechanized excavation were simulated. For the studied sections, numerical simulation is not capable of reproducing the high values of in-situ-measured surface settlements, applying Mohr-Coulomb constitutive law for soil. Based on results, for the mentioned case study, the range of estimated volume loss mostly varies from 0.2% to 0.7%, having an average value of 0.45%.

• Design & Manufacturing
• /
• v.15 no.2
• /
• pp.42-48
• /
• 2021

In this paper, when manufacturing large/multi-mold parts (more than 30 core parts),A mold manufacturing (tolerance) management system was established through design-processing linkage.The mold manufacturing (tolerance) management system is a design-based measurement shape/measurement position determination system, M/C processing-linked measurement drive system,It is composed of four parts: CAD-linked measurement result analysis system and manager mold part quality management system.In addition, the constructed system was applied to the field and the effect of system construction was evaluated by comparing it with the existing process.As a result of the evaluation, the measurement precision is within 0.02mm, and the time it takes to measure after the end of processing is shorter than that of the existing process.(12 hours → 2 hours) It was shortened to 16.7%.In addition, it was confirmed that the time required for reprocessing after measurement was reduced by 25% (4 hours → 1 hour) compared to the existing process.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.48 no.5
• /
• pp.292-296
• /
• 2022

Objectives: During Le Fort I osteotomy, the separation of the pterygomaxillary junction (PMJ) is a difficult procedure for most surgeons because it is invisible. In this process, damage to the posterior structures constituting the sinus or those adjacent to it, including the maxillary sinus posterior wall and pterygoid plate, may occur. We would like to investigate the effects of this on the inside of the maxillary sinus after surgery and whether there are complications. Materials and Methods: One-hundred patients who underwent Le Fort I osteotomy from 2013 to 2020 using cone-beam computed tomography images were classified into two groups (clean-cut type and fractured type) according to the PMJ cutting pattern. In addition, the mucosal thickness in the maxillary sinus was divided into preoperative, postoperative three months, one year, and the change over the course of surgery was evaluated retrospectively. Results: Of the total 100 cases, the clean-cut type numbered 28 cases and the fractured type totaled 72 cases. Among the fracture types, part of the sinus wall and the pterygoid plate were broken in 69 cases, and the maxillary sinus posterior wall was detached in three cases. There was no statistically significant difference in sinus mucosal thickening between the clean-cut type and fractured type of the PMJ, three months and one year after surgery between the two groups. However, there was a significant difference in sinus mucosal thickness at postoperative one year in the case where a partial detachment of the maxillary sinus posterior wall occurred compared to not. Conclusion: Even if there is some damage to the structures behind the PMJ, it may not be reasonable to spend some time on the PMJ separation process considering the overall postoperative complications, if there is no significant difference inside the sinus, or increased probability of postoperative complications.

• Geomechanics and Engineering
• /
• v.28 no.3
• /
• pp.283-298
• /
• 2022

Landslides triggered by the combination of heavy precipitation and anthropological disturbance in hilly areas cause severe damage to human lives, properties, and infrastructure constructions. A comprehensive investigation of the influencing factors and failure mechanisms of landslides are significant for disaster mitigation and prevention. This paper utilized the combination of detailed geological investigation, physical experimental testing as well as numerical modelling to determine the failure mechanism, and proposed a countermeasures of the Lantian landslide occurred on 2, July 2017. The results reveal that the Lantian landslide is a catastrophic reactivated slide which occurred in an active tectonic region in Southwest China. Because of the unique geological settings, the fully to highly weathered basalts in the study area with well-developed fractures favored the rainwater infiltration, which is the beneficial to slide reactivation. Engineering excavation and heavy precipitation are the main triggering factors to activate the slide motion. Two failure stages have been identified in the landslide. The first phase involves a shallow mass collapse originated at the upper slopes, which extends from the road to platform at rear part, which is triggered by excavation in the landslide region. Subjected to the following prolonged rainfall from 19 June to 2 July, 2017, the pore water pressure of the slope continually increased, and the groundwater table successively rise, resulting in a significant decrease of soil strength which leads to successive large-scale deep slide. Thereinto, the shallow collapse played a significant role in the formation of the deep slide. Based on the formation mechanisms of the landslide, detailed engineering mitigation measures, involving slope cutting, anchor cable frame, shotcrete and anchorage, retaining wall and intercepting ditch were suggested to reduce the future failure risk of the landslide.

• Explosives and Blasting
• /
• v.40 no.4
• /
• pp.35-46
• /
• 2022

While the construction of dismantling the old industrial complex and restoring the dismantled industrial site to its original natural environment the is underway. In this paper, we introduce a case of dismantling a turbine building which one of the a large steel frame structures in an old industrial complex by applying the progressive collapse method among the blasting demolition methods. We used a charge container that generates a metal jet to cut dismantling the turbine building. The thickness of the steel structure was adjusted to 30 mm or less by applying gouging, which was a method of digging deep grooves by gas and oxygen flames or arc thermal, in the part where the cutting thickness was thick in the blasting section. The total amount of charge used for the blasting of turbine building was 175 kg, 165 electronic detonators and 124 charge containers. As a result of the blasting demolition, the turbine building was collapsed precisely according to the estimated direction. The blasting demolition was completed without causing any damage to the surrounding facilities.

• Korean Journal of Social Welfare Studies
• /
• v.42 no.2
• /
• pp.97-122
• /
• 2011

After global economic crisis, most countries increased the welfare expenditure as a part of stimulus package. As a However welfare expenditure was decreased radically as the crisis was transmitted into the financial crisis. Which turning point is the welfare state going through now? Although the need for the welfare and the role of the state to take responsibility of public welfare has increased because of poverty and polarization, responses of the state against the crisis had focused on the aid to the financial industry and cutting taxes and showed limitations in coordination. Financial limitation of welfare expenditure, political individualism, the change of class politics and the mixture of the welfare institutions and financial institutions make have a pessimistic prospect of the retrenchment to the minimalist welfare state. As neoliberal state is continued cash benefits mainly for the middle class is being decreased. As a result, the direction the welfare states pursue is prospected to win over the poor by strengthening selectivity in welfare provision rather than class coordination.

• Journal of English Language & Literature
• /
• v.57 no.5
• /
• pp.787-812
• /
• 2011

This essay aims to explore Herman Melville's recognition and resolution of the vicious link between law and violence in his posthumous Billy Budd, Sailor (1924). In order to investigate the issues, this essay refers to Freud, Benjamin, Derrida, Lacan, and Žižek, all perceptive to the uncanny affinity of law and violence. Especially, Žižek's arguments of "superego" as an embodiment of cruel and destructive violence supplementing the official law and of "love" as an ethical possibility beyond the limit of the problematic law are introduced in this study to make Melville's reflection of the inseparableness between law and violence much clearer. John Claggart and Captain Vere embody the legal (superegoic) violence. Claggart even procurs secret enjoyment, in the name of maintaining positive law. Billy Budd discloses another violence defending his justness according to natural law. However, Melville suggests the possibility of suspending the problematic tie of law/violence through "love," as portrayed at the last part of the story. The two final words from Billy and Vere, as a sort of delayed dialogue between them after the event of their secret interview before Billy's hanging, suggest that they finally distance from the obscene nightly law of superego-respectively from outward punitiveness toward Vere and from inward punishment for Vere's excessive enforcement of Billy's hanging-and identify each other's lack as their own. Their love implicated in the last words is for the real other-in Lacan's sense-who discloses the constitutive lack or incompleteness of beings and aporia of the law. This essay's examination of Melville's representations about the superegoic violence as the (im-)possible condition of law and the possibility of withdrawing from it would help us recognize Billy Budd, Sailor as the author's own last word for the possible vision of love cutting the vicious knot of law/violence.

• Journal of Sericultural and Entomological Science
• /
• v.24 no.2
• /
• pp.43-54
• /
• 1983

In a field trial, the influence was studied by measurement of growth and leaf yields and chemical composition (in organic cations and anions and total nitrogen) with two nitrogen dressings (lower nitrogen treatment 25kg and higher nitrogen treatment 75kg urea/10a as the summer fertilizer) after the summer cutting. The results were as follows; 1. With increasingn nitrogen dressing, branch length and weight were enchanced. The fresh weight of leaves was higher to be 273.6kg/10a in the higher nitrogen treatment than in the lower nitrogen treatment on 20 September. 2. The moisture content of leaves lasted above 73% until on 30 August. Afterward it decreased sharply upto 63% on 20 September. In higher nitrogen treatment it was higher about 0.1∼1.8% than in lower nitrogen treatment. The increasing nitrogen dressings combined with leaf condition led to be soft until on 10 October. 3. Dry matter weight of leaves started decreasing around on 10 September, whereas that of branches increased until around 30 September indicating that the dry matter moved to branch and root from leaves. 4. The increase in Ca$\^$2+/ content was particularly evident, whereas the K$\^$+/ and Mg$\^$2+/ decreased with growth. The Ca$\^$2+/ content was much higher in the high nitrogen treatment than in the low nitrogen treatment. 5. With rapid decrease in total nitrogen and water in the leaves around the end of August, the Ca$\^$2+/ and Cl$\^$-/ which were higher in the lower part moved up to the upper part. Whereas the K$\^$+/, H$_2$PO$_4$$\^$-/ and SO$_4$$\^$2-/ which were higher in the upper part moved down to the lower part. 6. Total nitrogen content decreased sharply 3,200me/kg DM to 2,000me/kg DM at the end of August changing the maxmium content of total nitrogen from upper to lower part in the low nitrogen treatment on 12 September and in the high nitrogen treatment on 22 September, and an apex of branches was died and fallen 10 days after respectively. 7. The sum of cation in leaves (∑C) increased from 1400me/kg DM to 1600me/kg DM with growth, wherease that of anions (∑A) was approximatly the same during the whole growing season. As the result, the ionic balance (C-A) increased from 1000me/kg DM to 1200me/kg DM. 8. ∑C, ∑A and (C-A) were higher in the high nitrogen treatment than in the low nitrogen treatment due to be much higher of Ca$\^$2+/ content and higher of NO$\^$-/$_3$, SO$\^$2-/$_4$ and H$_2$PO$_4$$\^$-/ content.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.23 no.3
• /
• pp.159-168
• /
• 2003

This pot experiment was conducted in order to find out the effects of boron application($B_{0}$ /; control, $B_1$; 0.2, $B_2$; 2.0,$ B_3$; 6.0, $B_4$; 15.0 B me/pot) on the forage performance of pure and mixed cultures of orchardgrass and white clover. The 2nd part was concerned with the changes in the forage yields and concurrence index. The results obtained are summarized as follows: 1. The optimum boron application($B_2$) generally resulted in the increase of both forage yields, but the effects of boron application on them were different according to the forage species, whether it was a pure or mixed cultures, additional fertilization, and cutting order. The effects of boron application on the forage productivity were more obvious in white clover than in orchardgrass. 2. Owing to the decline of white clover as affected by the application of additional fertilizers, especially N, in the grass-clover mixed cultures, the effects of boron application on the white clover yields showed a numerical inferiority compared with the pure culture. It was recognized that the yield increase and botanical composition of white clover in grass-clover mixed cultures could be regulated by the application of additional fertilizers and boron. 3. The toxic boron application($B_3$ and $B_4$) resulted in a decreased yield of both forages. The yield change of orchardgrass tended to be similar between pure and mixed cultures, whereas it of white clover tended to be more negative in mixed than in pure cultures. 4. With the application of additional fertilizers, especially N, the botanical composition and concurrence index in grass-clover mixed cultures were relatively increased in orchardgrass, and decreased in white clover. The botanical composition of orchardgrass increased from 55% to 75%, whereas it of white clover decreased from 45% in the first half cutting to 25% in the second half cutting, respectively.