• 대한가정학회지
• /
• 제20권3호
• /
• pp.9-18
• /
• 1982

In this study, we attempted to make an original pattern of clothing for an abnormal type of figure, especially for the type of kyphosis. We measured the curvature of the spine of a woman with kyphosis with a Martin measuring instrument and a silhouetter in the following ways. First, we counted the rate of shrinkage of the standard lines drawn on the surface of the body according as the body moved. Secondly, placing the front and back darts, the front and back shoulder darts and the side darts according to“Munhwa”pattern, we made cubic cuttings of four moving postures as well as the standing one. Thirdly, we superposed the developed patterns of the standing and the moving postures, measuring the position change and the amount of the chaange of the darts, and compared them. The results are as follows: 1) In the developed pattern of a cubic cutting of the basic pattern and the standing posture, the neckhole became larger than that of the basic pattern, and the waist line was lowered than that of the basic pattern because the center back line was shortened due to the curved backbone. 2) As for the change of the standard line according to the movement, we found that the waist line, the center front line, the center back line, the bust width line, the upper back width line and the back width line became longer. Special consideration must be given to the function of the clothing for an abnormal type of figure. 3) The difference of the measurements between the cubic cutting and the body measurement regardless of the body movement is due to a gap by an acute angle at the jutted place between the developed pattern and the body surface. We found that the body measurement of the upper back width line, the back width line and the bust line became larger. Consequently, in making an original clothing pattern, it is desirable that we must not place the front and the back waist darts at the jutted place on the back from the functional and the aesthetic viewpoint of clothing. It is also desirable that we must widen the neckhole because the shoulder angle is close to a straight line due to a jut of the upper back width line.

• 대한토목학회논문집
• /
• 제42권6호
• /
• pp.775-786
• /
• 2022

원자력발전소 구조물을 포함하여 플랜트 구조물에서는 사용 중 설비보강을 위하여 벽체 및 슬래브에 관통부를 신설하는 경우가 빈번히 발생하고 있으며, 관통부 설치작업 중에 철근이 절단되는 사례가 일부 발생하고 있다. 이 관통부들은 설계 또는 건설 단계에서 고려된 것이 아니므로 설치 중 발생한 철근의 절단은 사실상 구조물의 손상이기 때문에, 관통부 주변 응력 전이범위 또는 유효폭을 고려한 구조물의 건전성 평가가 필요하다. 본 연구에서는 가동중인 원자력발전소 벽식 건물의 전단벽에 관통부를 신설할 경우에 발생하는 철근 절단의 영향을 평가하기 위하여 다양한 비선형 해석과 정적 가력 실험을 수행하였다. 그리고 관통부 신설과 철근의 절단으로 인한 벽체의 강성저하와 관통부 주변 철근의 응력 및 변형률 분포를 평가하였다.

• 한국기계가공학회지
• /
• 제5권4호
• /
• pp.59-64
• /
• 2006

High Speed Machining(HSM) reduces machining time and improves surface accuracy because of the high cutting speed and feedrate. Development of HSM makes it allowable to machine difficult-to-cut material and use small-size-endmill. It is however limited to cutting condition and tool material. In the machining operation, it is important to check main parameter of tool life and select optimal cutting condition because tool breakage can interrupt progression of operation. In this study, cutting parameters are determined to 3 factors and 3 levels which are a spindle speed, a feedrate and a width of cut. Experiment is designed to orthogonal array table for L9 with 3 outer array using Taguchi method. Also, it is proposed to inspect significance of the optimal factors and levels by ANOVA using average of SN ratio for tool life. Finally, estimated value of SN ratio in the optimal cutting condition is compared with measured one in the floor shop and reduction of loss is predicted.

• 복식문화연구
• /
• 제31권1호
• /
• pp.18-33
• /
• 2023

Zero-waste pattern cutting is a groundbreaking sustainable fashion practice. However, few brands and designers have pursued this method because it requires creative pattern design that diverges from the existing process of using pattern slopers. Therefore, application within the fashion industry is not sufficient. Therefore, in an attempt to highlight the key characteristics of zero-waste pattern design, this study classifies and analyzes cases in which similar designs employ zero-waste pattern-cutting techniques. We hope to make zero-waste pattern design more accessible by presenting realistic pattern-cutting guidelines. To this end, theoretical research on relevant literature, previous research, and online resources and an empirical analysis of cases involving zero-waste pattern cutting were conducted in parallel. As a result of the study, we were able to classify the factors of zero-waste pattern design in terms of fabric use, design, and composition. Regarding materials, our research revealed the importance of appropriate fabric width, understanding the difference between waste minimization and minimal fabric use, and easy reuse and recycling. In terms of design, the simultaneous progress of pattern and design work, adjustable loose silhouettes, and the use of surplus fabric for functional and decorative details emerged as key characteristics. For composition, we found that size adjustment limits, arrangement irregularity, and pattern shapes were crucial elements and that various arrangements revealed unlimited design potential.

• 한국터널지하공간학회 논문집
• /
• 제24권5호
• /
• pp.395-409
• /
• 2022

기존 암반 굴착공법이 갖는 한계점을 극복하기 위해 최근 연마재 워터젯 공법을 활용하는 연구가 활발히 진행되고 있다. 연마재 워터젯 암반굴착 공법은 암반에 연속적인 자유면을 형성하여 발파 시 발생하는 진동을 저감하고 굴착효율을 증진시키는 효과가 있다. 그러나 연마재 워터젯 절삭성능은 암반의 물리적 성질에 따라 변화한다. 따라서, 다양한 물리적 성질을 가진 암반이 혼재하는 굴착현장 특성상 효과적인 워터젯 활용을 위해서는 다양한 암종의 절삭성능을 분석하는 것이 필수적이다. 본 연구에서는 현무암과 화강암을 대상으로 수압, 이격거리, 이송속도를 변화시키며 절삭실험을 수행하고 결과를 분석하였다. 실험결과, 현무암은 화강암보다 평균적으로 약 41% 깊게 절삭되고, 절삭 폭은 약 18.5% 좁게 형성되었다. 본 연구결과는 향후 현무암과 같은 강도가 낮고 공극이 큰 암반 굴착현장에서 연마재 워터젯을 적용할 시 유용한 기초자료로 활용될 것으로 기대된다.

• 한국정밀공학회지
• /
• 제27권10호
• /
• pp.23-28
• /
• 2010

Resistance trimming and cutting processes of printed circuit board by making use of high power UV laser with nano-second pulse width have been proposed and investigated experimentally. Also laser-based application system with high flexibility and complex has been designed and adopted power controller, auto beam size control, auto-focusing and control program developed for ourselves. The function of each module shows that they can be reliable for industrial equipments. Resistance trimming method used a plunge and double cut process with $20{\mu}m$ spot size beam. Results show that double cut process is more effective to control resistance trimming in precision than plunge cut process.

• 한국산학기술학회논문지
• /
• 제10권9호
• /
• pp.2202-2209
• /
• 2009

모관과 지관의 다양한 접합형상에 대하여 접합궤적을 수학적으로 유도하였다. 이 접합궤적에 용접부의 루트갭 및 절단폭 등을 보정하여 실제적으로 절단궤적을 결정하여 NC 코드를 생성하고 그 경로를 확인하기 위하여 ghost 기능을 구현하였다. 척회전인 C축의 8개 구간별로 A, B축의 Tilting을 사용하여 개선 기능을 구현하였으며, 이는 절단궤적을 따라서 절단하면서 동시에 개선이 가능하도록 6축 CNC 파이프 코스터 전용 CAM 프로그램을 개발하였다.

• 한국연초학회지
• /
• 제11권1호
• /
• pp.71-77
• /
• 1989

The filling effects of test cigarettes prepared the different cutting width on the three brands (NC82, Burley21 and 88Light) were compared with their regular cigarette by the value of "Hardness" and "draw ressistance". Results obtained were as follows: 1. With enlargement of the shred width. The hardness of cigarettes became harder than the standard one in the same filling-weight When the shred width enlarged by 0.2mn from standard, the saving rate of tobacco materials would be 4~5%. 2. As the shred width became wider, Long strand was rich and short strand was poor. 3. The enlargement of the shred width may increase the standard deviation of filling-weight of cigarettes in some case.rettes in some case.

• 한국정밀공학회지
• /
• 제2권1호
• /
• pp.62-71
• /
• 1985

This is a study on the monitoring technique in tool failure and tool life by AE method. The relation between amplitude level of AE signal and flank wear width was studied by experiments. The relation between amplitude level of AE signal and tool life was also studied. As the result, it was observed that amplitude level of AE signal was only affected by cutting velocity. Amplitude level of AE signal was directly proportional to flank wear width and the increasing rate was related to cutting velocity. So, the relation between amplitude level of AE signal and tool life was represented as follow: $CT^n$ = $AE_{rms}$ where, n=0.35 C=9.5*$10^{-2}$

• 한국공작기계학회논문집
• /
• 제13권3호
• /
• pp.1-7
• /
• 2004

Abrasive water-jet(AWJ) machining can cut various materials such as metal, glass and plastics. However, the AWJ machining has some troubles including kerf, rounding and side taper. In this study, we experimently investigated the correlation between the traverse speed of the abrasive water-jet and the dimensional error of the workpiece according to the thickness and the types of the material. The specimen was the stainless steel and the mild steel and the predetermined contour cutting was conducted. A comer radius error, an uncut width and a kerf were measured and evaluated.