• The Journal of Engineering Geology
• /
• v.19 no.3
• /
• pp.345-350
• /
• 2009

The endpoint of the Yangbuk tunnel constructed at the national road between Gyeongju and Gampo is composed of massive cutting because the road is driven through the sides of mountain. PAP(Prestressed Anchor and PC Pannel) retaining wall as a slope stability method was established over this section. Part of the anchor in PAP wall became broken after six months. We performed inverse analysis through its measurements obtained until that time. An geological investigation to confirm the condition of ground layering and the attraction force test to find as to whether some errors might be present in the anchor were made. According to the back analysis, it was turned out that the value with soil parameter 90% that was applied to the original design was pertinent. In the redesign, the permissible stress in the anchor body was changed from 306 kN to 591 kN and 784 kN and the fixation position was increased from 11.0 m to 23.0 m. Nevertheless, five months have passed since the exchange of the anchor, the measurement results validate that stable state has been maintained. This research is considered a case that the immediate maintenance helps prevent the slope accidents.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.447-456
• /
• 2020

The study area is a slope in Dogye-eup, Samcheok-si, Gangwon-do. The cutting method was applied to this slope for stabilization in 2009 due to the influence of the waste-rock dump located at the top of slope. Recently, soil cracks and creep have occurred on this slope, and the drainage channel was damaged. Therefore, it was analyzed the topography change through photogrammetry using a UAV. Orthophotos were taken in April and October 2019 respectively. From the Orthophots, Digital Surface Model (DSM) was extracted. Time series analysis was performed by comparing each DSM. The topography of October was pushed forward while maintaining the topography of April. Through these features, it is judged that the soil creep is occurring in this study area.

• Journal of Environmental Impact Assessment
• /
• v.15 no.1
• /
• pp.1-12
• /
• 2006

Changes in the soil physical property and the topographic condition derived from agricultural activities like as farming activities, land clearance and cutting down resulted in environmental and economic problems including the outflow of nutrient from farms and the water pollution. Several theories on the soil conservation have been developed and reviewed to protect soil erosion in the regions having a high risk of erosion. This study was done using the USLE model developed by Wischmeier and Smith (1978), and model for the slope length and steepness made by Desmet and Govers (1996), and Nearing (1997) to evaluate the potential of the soil erodibility. Therefore, several results were obtained as follows. First, factors affecting the soil erosion based on the USLE could be extracted to examine the erosion potential in farms. Soil erodibility (K), slope length (L), and slope steepness (S) were used as main factors in the USLE in consideration of the soil, not by the land use or land cover. Second, the soil erodibility increased in paddy soils where it is low in soil content, and the very fine sandy loam exists. Analysis of the slope length showed that the value of a flat ground was 1, and the maximum value was 9.17 appearing on the steep mountain. Soil erodibility showed positive relationship to a slope. Third, the potential soil erodibility index (PSEI) showed that it is high in the PSEI of the areas of steep upland and orchard on the slope of mountainous region around Dokjigol mountain, Dunji mountain, and Deummit mountain. And the PSEI in the same land cover was different depending on the slope rather than on the physical properties in soil. Forth, the analysis of land suitability in soil erosion explained that study area had 3,672.35ha showing the suitable land, 390.88ha for the proper land, and 216.54ha for the unsuitable land. For unsuitable land, 8.71ha and 6.29ha were shown in fallow uplands and single cropping uplands, respectively.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3
• /
• pp.402-407
• /
• 2013

In this paper, the image processing for flexible disk grinding and the effect of the grinding conditions on the flat zone length of a workpiece are investigated, with the purpose of automating the grinding process. To accomplish this, three issues should be carefully studied. The first is finding the relationship between the flat zone length and the grinding conditions such as the cutting speed and feeding speed. The second is developing a neural network algorithm to predict the flat zone. The third is developing an image processing algorithm to measure the flat zone length of a workpiece. Slope analysis is used to determine straight and curved sections during the image processing. For verification, the estimated length and the length from the image processing are compared with the length measured by a projector. There is a minimum difference of 1.7% between the predicted and measured values. The results of this paper will be useful in compiling a database for process automation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.1
• /
• pp.206-217
• /
• 2001

The purpose of this study was to estimate that the relations of weathering speed and shear strength of granite soil by tracing the weathering depth of granite soil from the very moment of its cutting. The results obtained this follows ; 1) The relationships among Nc, Li and CEC, Li>6%, CEC>14 corresponds to Nc=2~30, and 4%${\phi}$)increases at a standard pressure. 3) And Nc=0~50 corresponds to $27{\sim}50^{\circ}$ of internal fiction angle and to 12~49kPa of cohesion. That is to say, internal friction angle(${\phi}$)corresponds better than cohesion(c). In conclusion, this study suggests that in simplified dynamic cone penetration test a penetration boundary line of 5 centimeters is decided at around Li=4%, CEC=3(meq/100g) which is classified as a completely weathering soil. It also appears that CEC increases as Li increases while Nc decreases.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.10 no.2
• /
• pp.82-90
• /
• 2007

Recently, the development project is conducting disaster effect estimation to breed disaster, and cope these disaster beforehand provoking soil erosion and flood. Therefore, it is important to analyze and reduce of these disaster. In this study, it is intended to extract LS and C factors of soil erosion through the digital image. The photogrammetric technique, which employs the Remote Control Helicopter equipped with a non-metric digital camera, was used for the efficient survey and analysis of cutting slopes. As a result, we obtain more objective value of soil erosion factor using digital image.

• Current Research on Agriculture and Life Sciences
• /
• v.1
• /
• pp.113-140
• /
• 1983

This is a study on a landscape planning along the street 1~4, which are gateways to Taegu city and an important scenery. Therefore, emphasis was given to provide a bright, clean and beautiful first impression to visitors and citizens. The area is being developed for education and athletic park. Plans to construct a fountain, pergolas and a pond were set up to complement the active and passive facilities to the existing a athletic facilities in the area. Since D part in the area have alkali soil (pH 8.1), soil amendment is necessary for successful growth of trees and ground covers. When the area is filled or added with new soil for soil amendment, it will be important to use fresh soil which can support plant growth. It will be ideal to use ground covers and shrubs on the existing retaining walls along the street for keeping natural vegetation and slope stability instead of further cutting and reconstruction. It is not reasonable in technical and economic sense to remove rocks of the slope for planting trees. In order to harmonize plant color distribute, tall needle and broad leaf trees in the background as a screen, flowering trees were arranged in groups at front, and annuals were mass-planted along the footway. Natural-form-trees will be planted because they not only serve as a greenbelt but also are more economics in maintenance than formative trees.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.1
• /
• pp.88-93
• /
• 1999

In modern period, the history of highway landscaping can be divided into three stages. The first stage from the late 1960s to the early 1970s : during this period revegetation operation started and landscape architecture was introduced. The second stage from the late 1970s to the early 1980s : during this period the definition of functional planting which had played the most important role in highway landscaping was established. Also, highway landscaping was influenced by Japan, and the revegetation of highway slopes were applied with Seedspray, Block-sodding methods, and so on. The third stage from late 1980s to the present : during this period eco-landscaping was introduced and began to mix with ecosystem techniques. The revegetation works of cutting-rock slopes have widely been developed. Many people think that landscaping is necessary for us, and that revegetation method is effective to conserve slope environment. Based on accumulated data we have to improve the function of landscaping and revegetation method, and also have to establish the method of landscaping harmonized with our own landscape.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.796-805
• /
• 2005

Most rockfall prevention net among the rockfall prevention equipment that is constructed in around the road is actuality lack of function by quantitative research insufficiency etc.. Most of rockfall prevention net are composed to setting needle, perpendicular and horizontal wire rope and wire net. Also, function of rockfall prevention net depend on setting needle and the wire net and perpendicular and horizontal wire rope are fixed by setting needle. when unreasonable load is offered setting needle, rockfall prevention net can lose the function and happen continuous falling off of rockfall prevention net. Because rockfall prevention net have a such structural defect, improvement had been required in reply. So in this paper, spot application of Rock Bolt & Net Connection method and falling rock support ability are estimated by numerical analysis. As a result, when Rock Bolt & Net Connection Method is applied to cutting slope, decreases of stress and displacement is examined than current rockfall prevention net.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.113-120
• /
• 2005

Soil nailing system can be mentioned to a method of supporting as the shear strength of in-situ soils is increased by passive inclusions. In the general soil nailing system, facing walls are used in two kind of a lattice concrete block or a cast in placed concrete wall. A case of lattice concrete blocks is used in slow slopes greater than 1:0.7. Also, a case of a cast in placed concrete wall is used in steep slopes less than 1:0.5. The cast in placed concrete walls are constructed to 30cm thick together with a shotcrete facing. In this study, the assembling soil nailing method as a new soil nailing system is proposed. This method is constructed assembly using precast concrete panels. Therefore ability of the construction and quality of the facings can be modified than a usual soil nailing system. Also, this method can be obtained the effects that a global slope stability increase, as precast concrete panels is put on cutting face after excavating a slope.