KSCE Journal of Civil and Environmental Engineering Research
/
v.42
no.2
/
pp.181-186
/
2022
Dam slope RIM is a highly important contact interface where the main body and the base surface are connected. In general, when the grouting for the slope of the dam structure is designed, it is planned using limited data (drilling, geological map, etc.). This makes it very difficult to accurately consider the original ground characteristics of the slope RIM grouting target, In addition, when the grouting volume planned during the design is drilled and injected into the original ground where the waterstop is secured, there is a possibility that the original ground with the waterstop is disturbed and the effect of the waterstop is rather diminished. In order to overcome such problems, it is more suitable to first consider geological conditions and determine whether to perform optimal grouting on the original ground through on-site repair tests before performing RIM grouting. In this paper, to determine the grouting of the RIM unit, a pilot hole water pressure test was performed on the rock of the slope in the target section. The analysis shows grouting volume of 1 Lugeon or less, and the cement injection amount also shows the injection result of 1 kg/m or less. In this case, performing grouting is rather counterproductive. This result can be evaluated through a rock of which some degree of order of mass is secured, as it is a dam design standard of 1 Lugeon or less when analyzed, using the results of visual observation and geological map creation during slope cutting. Therefore, in conclusion, it is preferable to make the decision for using RIM grouting on the slope of the dam body structure, based on 1 Lugeon in a rock state, and the cement injection amount also at 1 kg/m.
The changes in the 4th industrial revolution era are not limited to specific sectors, but affect all sectors of industry. Thus all companies are required to respond effectively to changes. Some companies response by adopting cutting-edge ICT and some companies improve the organizational structure, or enhance the competence of individual employees. This study is based on the assumption that the responses to the change in the 4th industrial revolution era should not be uniform, and that the response strategies and priorities should vary according to the characteristics of the companies. The purpose of this study is to suggest both different response strategies and the priority of the responding factors(areas) to small and medium-sized enterprises. Data were collected through the semi-Delphi method. As a result of data analysis, the priorities of the medium-sized enterprises were as follows: introduction of IT-strengthening the competence of the individuals - establishing technology infrastructure-improving organizational structure - efficiency of work - improving organizational culture. While the priorities of the response factors(area) of the small-sized companies were as follows: strengthening the competence of the individuals - efficiency of work - introduction of IT - establishing technology infrastructure - improving organizational structure - improving organizational culture.
AI is accepted not only in the private sector but also in the defense sector as a cutting-edge technology that must be introduced for the development of national defense. In particular, artificial intelligence has been selected as a key task in defense science and technology innovation, and the importance of data is increasing. As the national defense department shifts from a closed data policy to data sharing and activation, efforts are being made to secure high-quality data necessary for the development of national defense. In particular, we are promoting a review of the business budget system to secure data so that related procedures can be improved to reflect the unique characteristics of AI and big data, and research and development can begin with sufficient large quantities and high-quality data. However, there is a need to establish standardization and quality standards for structured data and unstructured data at the national defense level, but the defense department is still proposing standardization and quality standards for structured data, so this needs to be supplemented. In this paper, we propose an unstructured data set standard format for defense unstructured data sets, which are most needed in defense artificial intelligence, and based on this, we propose a standardization method for defense unstructured data sets.
This study was carried out to investigate the characteristics of root growth in Kentucky bluegrass sod(KBS) and creeping bentgrass sod(BGS) transplanted in summer(August 9) and fall(September 19), respectively. Hydroponic system was also used to observe rooting development in the study. Root development differed in KBS by transplanting time. It reached to more than 5 cm after 100 days In summer and 50 days in fall. However, BGS's root grew over 6cm after 40 days, regardless of the season. There was no significant differences in BGS, regardless of any cutting treatment. In the case of KBS, it was best with sod culled with 0.5cm deep and 1.5cm long. But it grew beyond 5 cm in root growth under any treatment after 40 days in transplanting. In a hydroponic study, BGS produced root over 100cm for 80 days through a summer season. However, the root of KBS did only grow in condition below $20^{\circ}C$. These results indicated that root growth characteristics were variable in BGS and KBS. It was considered that rooting development of BGS might be improved with sufficient irrigation in summer, and KBS grows well in lower temperature of $10{\sim}18^{\circ}C$, as compared with BGS. As to establishing the lawn with a sodding method, it should be careful in transplanting time, especially KBS.
This paper aims to establish the technical style of roof tiles by analyzing East Asian roof tile making techniques. It will examine the existing main research data, such as excavation results and the subsequent analysis of the roof tiles' production traces, as well as references and transmitted techniques. Regions are grouped according to technical similarity, then grouped again by artistic styles of pattern and shape and by the technical styles of tools, procedures, and manpower plans. Accordingly, intends to find out whether an understanding of technical style can facilitate an understanding of not only cultural aspects, but also the causality of techniques. Korean, Chinese and Japanese tools were examined, and procedures for making roof tiles were classified into 4 groups. In a superficial way, China, Okinawa, Korea, and Honshu share similar technical traits. Research of procedural details and manpower plans revealed characteristics of each region. As a result, comparisons were made between each region's technical characteristics attempting to investigate their causes. The groups were classified according to their possessing techniques, but it was revealed that East Asia's shared production techniques were based on architectural methodss. The skill of "Pyeon Jeol(Clay Cutting)" classified according to its possessing techniques, turned out to be one such technique. Also, the procedure of technical localization based on the skill of "Ta-nal(Tapping)" showed that the condition of this technique was the power to localize in response to a transfer of techniques. Previous comparison parameters of artifacts would have been a similarity of style originated from exchanges between regions and stylistic characteristics of regions decided by the demander's taste of beauty. This methodology enlarges cultural perception and affords a positive basis of historical facts. However, it suggests the possibility of finding cultural aspects' origins by understanding the technical style and seeing same result in view of "technology culture."
This study was carried out to evaluate three winter active synthetic varieties in a succeeding generations of improvement and polycross progenies of seven genotypes selected at the cool and wet climate of the Western Oregon, in their performance of the polycross progeny test comparing with a control variety, high yielding 'Fawn', at Daejon, Korea. Various plant and leaf characteristics, especially related to photosynthesis, and forage production during the first summer after the establishment were examined. The important conclusions of this study are summarized as follows: 1. The differences of leaf fresh weight among groups and control exhibit genetic differences. The a verage of leaf fresh weight of polycross progeny group was the heaviest and those of winter active synthetic varieties in the succeeding generations of improvement was heavier than variety 'fawn'. Within polycross progeny group the genotypes exhibit genetic differences for leaf dry weight. 2. The leaf area exhibited genetic differences among groups and control. The average of winter active synthetic varieties in a succeeding generation was larger than variety 'Fawn'. Those oi the polycross progeny group was the largest among groups and control. 3. Differences of specific leaf weight(S. L. W.) among and within varieties, genotypes and control were not significant. Further investigation in this respect is necessary through the study of the diurnal change in S. L. W. 4. Differences of leaf width among groups and control exhibited genetic differences. The average leaf width of winter active varieties was larger than those of 'Fawn' variety. And those of polycross progenies of genotypes was the largest. 5. Plant height of 'fawn' variety in the first measurement was higher than those of winter active tall fescue varieties and genotypes. The deviation in plant height among polyeross progenies of seven genotypes gave a great deviation. The regrowth ability of plant height was not different suggesting that this characteristics was about the same among and within groups and control. 6. Plant width, spreading ability, improved through the succeeding generations of the improvement of the winter active synthetic varieties for the first measurement. Differences of plant width at the second measurement among genotypes within polycross progeny group were big enough to show the genetic difference. 7. Tiller number of the winter active synthetic varieties and the average of genotypes in polycross progeny was more than those of the control 'Fawn' in the first measurement. On the second measurement, the differences of tiller number appeared among three synthetic varieties indicating improvement, and there were genetic differences among seven genotypes in polycross progeny test. 8. Forage yield on the first cutting showed a considerble improvement of forage yield in the more advanced generation of synthetic varieties and genetic differences among seven genotypes in the polycross progeny test. The average of polycross progeny group was higher than those of the control or three winter active varieties. It was suggested that we could make a further improvement for the forage yield. 9. The regrowth ability of these winter active varieties and genotypes was about the same capacity at least on the measurement of the regrowth in forage yield and plant height during summer. 10. On the whole, the averages of the polycross progeny group was in the highest value and those of synthetic varieties were higher than the control variety, 'Fawn', for the most characteristics except S. L. W. and the plant height on the first measurement even though the differences were not always significant. And there were genetic differences among seven gentypes in their performance of the polycross progeny. 11. Although it was not always sgnificant, the most advanced winter active variety, '1002', had in the highest value for all plant characteristics and forage yield measurements than the other two varieties, '1001'. 12. The results of the association study among various characteristics were quite agreeable and would be useful in the selection of desirable genotypes for the development of a better variety.
This experiment was conducted to investigate the effect of application level of swine slurry on the growth characteristics and yield of sorghum$\times$sudangrass hybrid and $NO_3-N$ content in infiltration at experimental field of Grassland and Forage Crops Division, National Livestock Research Institute, RDA from 2000 to 2002. Treatments were consisted of non fertilizer(NF), chemical fertilizer(CF), 100% swine slurry(SS 100), 150% swine slurry(SS 150), 200% swine slurry(SS 200) and 100% swine slurry + CF 50%(SS100 + CF 50) with randomized complete block design and three replications. Growth of sorghum$\times$sudangrass hybrid was not nearly different among the treatments, but early growth of swine slurry treatments was better than that of CF, and regrowth after 1st cutting was shown better in CF and SS 100+CF 50 with adding application of chemical fertilizer. The sugar content(brix %) was tends to be increased with swine slurry application. Dry matter(DM) yields of SS 100 and SS 150 were lower 15 and 6% than that of CF, respectively, and SS 200 was similer to CF, but there was not found significant difference among all treatments. The content of crude protein(CP), acid detergent fiber(ADF), and neutral detergent fiber(NDF) did not show the difference. The content of $NO_3-N$ in infiltration water was not more than CF by the 55 150 application, but more than by SS 200 and 55 100+CF 50 treatment.
Kim, Eun-Mi;Kim, Hwa-Jeong;Choi, Chang-Yong;Kang, Chang-Wan;Kang, Hee-Man;Park, Chan-Ryul
Korean Journal of Environment and Ecology
/
v.23
no.6
/
pp.528-534
/
2009
Styan's Grasshopper Warblers (Locustella pleskei) are vulnerable species distributed in East-Asia only. Its known breeding sites in Korea are remote islets including Hongdo Islet, Chilbal Islet, Mara Islet, and Chuja Islets, and, therefore, the breeding biology of this species is still poorly known. This study was conducted on Mara Islet (N $33^{\circ}$ 06', E $126^{\circ}$ 16') from May to September 2008 to investigate the breeding status and breeding site characteristics of the grasshopper warblers. A total of 11 breeding pairs and their nests were found on trees and shrubs at artificially planted forests and hedges of Pinus thunbergii. The grasshopper warblers preferentially utilized the shrub trees for nesting places, and major nesting trees were Camellia japonica, Pittosporum tobira and Pinus thunbergii as nesting trees. Average heights of nesting trees and nests were $2.77{\pm}1.10m$ and $1.75{\pm}0.56m$, respectively. The grasshopper warblers selected lower shrubs and trees for nesting than randomly selected ones around them, probably to avoid strong and prevailed winds in flat and un vegetated environments on Mara Islet. The shape of nests was a round bowl-type, and measurements of nests were $11.9{\pm}0.5cm$ in exterior nest diameter, $11.1{\pm}1.1cm$ in height of exterior nest, $5.8{\pm}0.4cm$ in interior nest depth, and 6.0cm in interior nest diameter. It incubated eggs until the early August on Mara islet, and incubation periods of Mara Islet was possibly later than that of other areas. Furthermore, the clutch size in the study area was three, and they laid smaller number of eggs than normal clutch size (4~5 eggs) reported in other areas. Although we could not observe any nest predator on this species in the study area, selective cutting and pruning of trees will diminish dense shrub layer of forests. Therefore, it may affect the breeding of this threatened species which prefers dense shrubs of artificially planted forest of Pinus thunbergii. This study suggests that detailed and consistent further research on breeding biology and habitats of the grasshopper warblers are needed to conserve and manage of Pinus thunbergii forests on Mara Islet as an important breeding site of Styan's Grasshopper Warblers.
Purpose: In this study, we evaluated the physical and thermal properties of the compositions made by blending glass fiber (GF) of different contents into glass fiber polyamide-66, and investigated if the compositions applying to the glasses frame to replace the TR-90, which is polyamide-12 resin used as an injection-type spectacle frame material. Methods: To investigate the characteristics change of polyamide-66 (PA-66) compositions with the change of the content of glass fibers, we produced a composition of the content by using a twin-screw extruder. The mechanical strength of the composition production was measured and coating properties as well as cutting processability were evaluated. We evaluated the applicability of the glasses frame by comparison the results of new compositions with characterizations of traditional TR. Results: For the results of the characterization of Polyamide-66/GF composition, we found that the higher increase of content of the glass fiber, the less mold shrinkage rate, and the mechanical strength was increased. Tensile strength increased from $498kg/cm^2$ for 0 wt% of the content of the glass fibers to $849kg/cm^2$ for 30 wt% of the content of the glass fibers. As a result of a coating evaluation, the strength of coating was 4B in the GF 5wt% and 5B, which was extremely good coating characteristics, in the over than GF 5 wt%. Conclusions: In case that 30 wt% of the glass fiber was blended, the mechanical strength was greatly improved, the hardness was increased, injection temperature increased due to increase of the viscosity, and the flow mark of the product may occur. The paint coating of PA-66 blended with glass fiber was all excellent. With general evaluating physical properties and workability properties it was determined that around 10 wt% of the content of the glass fibers was possible to apply a spectacle frame.
Pseudotachylytes, produced by frictional heating during seismic slip, provide information that is critical to understanding the physics of earthquakes. We report the results of occurrence, structural characteristics, scanning electron microscopic observation and geochemical analysis of pseudotachylytes, which is presumed to have formed after the Late Cretaceous in outcrops of the Paleoproterozoic granitic gneiss on the Bulil waterfall of the Jirisan area, Yeongnam massif, Korea. Fault rocks, which are the products of brittle deformation under the same shear stress regime in the study area, are classified as pseudotachylyte and foliated cataclasite. The occurrences of pseudotachylyte identified on the basis of thickness and morphology are fault vein-type and injection vein-type pseudotachylyte. A number of fault vein-type pseudotachylytes occur as thin (as thick as 2 cm) layers generated on the fault plane, and are cutting general foliation and sheared foliation developed in granitic gneiss. Smaller injection vein-type pseudotachylytes are found along the fault vein-type pseudotachylytes, and appear in a variety of shapes based on field occurrence and vein geometry. At a first glance fault vein-type seudotachylyte looks like a mafic vein, but it has a chemical composition almost identical to the wall rock of granitic gneiss. Also, it has many subrounded clasts which consist predominantly of quartz, feldspar, biotite and secondary minerals including clay minerals, calcite and glassy materials. Embayed clasts, phenocryst with reaction rim, oxide droplets, amygdules, and flow structures are also observed. All of these evidences indicate the pseudotachylyte formed due to frictional melting of the wall rock minerals during fault slip related to strong seismic faulting events in the shallow depth of low temperature-low pressure. Further studies will be conducted to determine the age and mechanical aspect of the pseudotachylyte formation.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.