• Journal of the Korean Society of Safety
• /
• v.25 no.1
• /
• pp.65-71
• /
• 2010

In this study, a series of finite element analysis using LUSAS were performed in order to assess the quantitative effects of repair and retrofit of stringer in steel plate girder railway bridge with fatigue cracks. And cutoff types of end part of upper flange were considered as right-angled type and round-angled type. Also, as a method of repair and retrofit of fatigue cracks in stringer, perforation of stop-hole and installation of bracket were considered. From the analysis result, it was possible to assess the fatigue safety and fatigue life of stringer with fatigue cracks, and to estimate the stress intensity factor range in cut-off part of stringer using J-integral method. Also, according to the method of perforation of stop-hole and installation of bracket, it was possible to calculate the crack propagation life at the cut-off part of stringer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.809-812
• /
• 2001

We were fabricated of NiCr thin film resistors on A1$_2$O$_3$and SiO$_2$/Si substrates by dc magnetron sputtering system. The AC characteristics of resistors were studied. The cut-off frequency were found >10 MHz for the resistors with 39 ohm value of Alumina substrates, but the cut-off frequency were found 400 kHz for the resistors with 168 ohm value of SiO$_2$/Si substrates. In high frequency applications, the substrate selection is the most important factor.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.2
• /
• pp.125-130
• /
• 2011

This paper shows a method to design complementary filter using least square. The complementary filter is one of useful filters estimating angle. The basic concept of this filter is to enhance advantages of each sensor that angle detecting using a gyroscope has good accuracy at a high frequency and an accelerometer at a low frequency. When designing complementary filter, the most commonly used method is using cut-off frequency. However, it may be not easy to obtain a cut-off frequency. This paper presents a systematic method to determine the coefficients of the complementary filter using well-known linear least squares minimizing error between estimating angle and true angle.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.11
• /
• pp.624-629
• /
• 2004

The UHF electromagnetic waves excited by PD pulses propagate along the GIS busbar not only TEM mode, but also TE and TM mode. Generally the waves detected by the UHF sensors are those of high order modes and such waves can only propagate higher than cut-off frequency. In this paper, the cut-off frequency of 362[kV] GIS for each modes is computed and the electromagnetic field of each propagation modes is simulated by FEM(Finite Element Method) program. Frequency band of each TEmn/TMmn modes was determinated by simulation results and was discussed optimal position of UHF sensor from this results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.169-169
• /
• 2010

650nm 적외선 차단 필터를 Macleod 프로그램을 이용하여 설계하고, 이온보조증착(IAD) 장비를 이용하여 코팅한 후 투과도, 파장, 두께특성을 조사하였다. 차단필터의 증착물질은 $TiO_2$ (n=2.30) /$SiO_2$ (n=1.46) 을 사용하여 45층의 다층 박막으로 증착하였다. 코팅된 차단필터는 차단파장이 651 nm로써 평균 ${\pm}5$ nm 이내의 편차를 보였다. 420~630 nm 파장영역에서 평균 투과도는 89%이었으며, 투과도의 균일도는 약 2.12로써 매우 균일하였다. 투과도기 단파장 영역에서 감소된 것은 다층박막 증착 시 산소가 결핍된 것으로 판단된다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.5
• /
• pp.1005-1009
• /
• 2010

This paper presents a digitally-controlled filter calibration technique for biquad RC filter using self oscillation. The biquad RC filter is converted to a fully-differential ring oscillator by changing its resistor connections, where the oscillation frequency reflects the cut-off frequency. The proposed calibration circuit measures the oscillation frequency by counting with a fixed higher-frequency clock and then tunes it to a desired frequency with a digital frequency-locked loop including a PI controller. Because the proposed circuit directly measures the cut-off frequency of the filter itself and calibrates it with the small area digital circuits, the area and the power consumption are much small compared with conventional works. When it is implemented in a 65nm CMOS process, the calibration circuit except the filter consumes the area of 80um X 50um and power consumption is 443uA at 1.2 V supply voltage.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.249-252
• /
• 2002

we have studied the characteristics of PHEMT's with gate recess etching method. The DC characterization of PHTMT fabricated with the wide single recess methods is a maximum drain current density of 319.4 ㎃/mm and a peak transconductance of 336.7 ㎳/mm. The RF measurements were obtained in the frequency range of 1~50GHz. At 50GHz, 3.69dB of 521 gain were obtained and a current gain cut-off frequency(f$_{T}$) of 113 CH and a maximum frequency of oscillation(f$_{max}$) of 172 Ghz were achieved from this device. On the other hand, a maximum drain current of 367 mA/mm, a peak transconduclancc of 504.6 mS/mm, S$_{21}$ gain of 2.94 dB, a current gain cut-off frequency(f$_{T}$) of 101 CH and a maximum frequency of oscillation(f$_{max}$) of 113 fa were achieved from the PHEMT's fabricated by the .narrow single recess methods.methods.

• Proceedings of the KSPS conference
• /
• 2007.05a
• /
• pp.247-250
• /
• 2007

The affricates of the Korean were alveolar sounds in the 15th century. Alveolar sounds have changed to post-alveolar or alveo-palatal sounds since the 18th century, at least in Southern Korean. These days, the advanced articulation of the affricates are observed, especially in the speech of young generations. The aim of this paper is to show the differences of the affricates when they are pronounced in alveo-palatal and in a more advanced position than in alveo-palatal by their cut-off frequencies. We have recorded speeches of freshmen(in their early twenties) at Seoul National University. The result was that the cut-off frequency of the advanced articulation in auditory observations was higher than that of the others. We have found in particular, that women have tendency to advance their place of articulation of the affricates.

• Textile Coloration and Finishing
• /
• v.15 no.2
• /
• pp.68-75
• /
• 2003

In this work, ultrafiltration(UF) membranes were prepared using polyethersulfone(PES). The polymer was dissolved in various solvent, such as N, N-dimethyl formamide(DMF), N,-dimethyl acetamide (DMAc), N,N-dimethyl sulfoxide(DMSO) and N-methyl-2- pynolidone(NMP). Each polymer solution was casted on the glass plate, and immersed into non-solvent bath. In this way finely porous UF membranes were prepared by phase inversion method. The cross sectional structure of PES membrane was asymmetric which was consist of sponge-like sublayer, finger-like toplayer, and active skin layer. From the solute rejection experiments, the molecular weight cut off of the prepared membrane in various solvent was evaluated 10,000 for DMF, 30,000 for DMAc, 50,000 for DMSO, and 10,000 for NMP respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.98-103
• /
• 2000

The cut-off is a unique feature associated with duct acoustics due to the presence of duct walls. Duct geometry effect on sound radiation is another issue of duct acoustics. The radiation of duct internal noise to ambient from duct open ends with various geometries is studied via numerical methods. The linearized Euler's equations in generalized curvilinear coordinates are solved by the DRP finite difference scheme. A number of accurate boundary conditions are used at boundaries for the computational domain to minimize the non-physical reflections. The far field sound pressure levels are computed by the Kirchhoff integration method. We investigate the cut off phenomana and duct geometry effects on sound radiation with numerical results.