• The Journal of the Petrological Society of Korea
• /
• v.10 no.2
• /
• pp.95-105
• /
• 2001

U-Pb age determination was performed on the zircon fractions separated from the metamorphic rocks of three locations of the Gyeonggi Massif. The ages obtained from the upper and lower intersections between concordia curve and discordia lines made of the zircon fractions separated from the rocks of each locality we: $2168\pm$24 Ma and $1227\pm$40 Ma for the Yongduri Gneiss Complex, $1955\pm$22 Ma and $493\pm$32 Ma for the Euiam Group, and $3712\pm$244 Ma and $1613\pm$51 Ma for the Yongmunsan Group (2$\sigma$ errors). The upper intercept ages from the Yongduri Gneiss Complex and the Euiam Group of Gyeonggi massif are very similar to those obtained from the granitic gneisses and the porphyroblastic gneisses of Yeongnam massif respectively. Such similarities suggest that Gyeonggi and Yeongnam massifs might situate under the similar tectonic and geographic environment during ca. 2.2-1.9 Ga. The upper intercept age of Youngmunsan Formation (3.7 Ga) shows large error, because most of the zircon fractions are plotted very close to the lower intersection. It is necessary to investigate further to confirm this age. However, It may suggest the possibility of occurrence of the oldest crust of the northeast Asia similar to the one reported recently from the northeast China. The lower intercept age of the Yongmunsan Group is interpreted to indicate strong metamorphism. Such age postdates the 1.85-1.7 Ga metamorphism and igneous activities occurred in the Yeongnam massif, which might record the late Paleoproterozoic tectonic activities simultaneously occurred in both massifs.

• Journal of the Korea Concrete Institute
• /
• v.24 no.5
• /
• pp.585-596
• /
• 2012

In this study, the flexural characteristics of reinforced polymer concrete T-beams strengthened with GFRP, typically used for bridges and parking structures, are investigated. A method to determine the flexural failure mode of reinforced polymer concrete T-beams comprised of compression failure (CF), tension failure (TF), and fiber sheet failure (FF) for different levels of GFRP strengthening is proposed. Moreover, the present study provides a formula to calculate the design flexural strength for each failure mode. In reinforced polymer concrete T-beams strengthened with GFRP, an ideal failure mode can be achieved when the failure occurs in the following order: 1) yield of steel reinforcement, 2) failure of GFRP, and 3) compression failure of concrete. In the case of FF mode, due to GFRP failure before the polymer concrete crushing in compression region, a concept of equivalent rectangular block based on the ultimate limit state of concrete should not be used. Thus, this study suggests an idealized stress-strain curve for polymer concrete and finds parameters for stress block, ${\alpha}$ and ${\beta}$ based on the strain distribution in polymer concrete. Furthermore, the present study suggests an aspect ratio of 2.5 by examining the compressive stress distribution and design flexural strength characteristics for different aspect ratio of T-beams. This study also provides a design flexural strength formula, and validates its acceptability based on experiment and theoretical analysis.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.24 no.6
• /
• pp.397-404
• /
• 1991

The steady state and decay characteristics of primary fluorescenece of phytoplanktons including Cyanophyceae and Cryptophyceae were investigated in vivo. At 580-640 nm region, fluorescence emission spectra were obtained from all algae examined. The observed fluorescence emission maxima were similiar$(\pm3\;nm)$ except Synechocorcus sp. (SYN). Considered $\lambda_{max}$ of emission spectra of phycobiliproteins and the excitation spectra with $\lambda_{max}=540-560nm$, it seems to be originated from biliproteins. Fluorescence lifetimes $(\tau)$ and decay curves were compared with standard solution of candidate organic compounds, b-phycoerythrin. The $\tau$ values obtained for phytoplankton with $\lambda_{max}=580nm$ were different depending upon the species of algae. The observed $\tau$ values were ranged from 1.39 ns to 1.95 ns. These are considerably shorter than $\tau(3.23\;us)$ for standard solution of b-phycoerythrin. The reduction of $\tau$ for phycoerythrin in vivo seems to be originated from effective energy transfer system between Chl. a and phycobiliprotein in intact cell. There are subtantial differences in fluorsecence spectra and lifetimes at the class level. At the species level, differences seems to be much smaller. The result of experiment suggests that measurement of fluorescence lifetimes may be helpful in the rapid characterization of algae. Direct application will likely be found in combination with the measurement of other luminescence parameters.

• The Korean Journal of Nuclear Medicine
• /
• v.26 no.2
• /
• pp.307-311
• /
• 1992

Anorexia, nausea, and vomiting are one of the most frequent symptoms in viral hepatits patients. These may be due to poorly detoxified substances by dysfunctioned hepatocytes or by gastritis, but the pathophysiology is not totally understood. The symptoms interfere with adequate nutrient intake and are managed by metoclopramide, which accelerates gastric emptying. Thus delayed gastric emptying may well be a contributing factor to such symptoms. To determine such a relationship, we measured gastric emptying time in 11 normal subjects,9 acute (AVH), and 12 chronic B viral hepatitis (CVH) patients. All were males with a mean age of 23 years. An egg was labeled with 0.5 mCi of $^{99m}Tc-sulfur$ colloid, fried, then eaten between 2 slices of bread with 100 cc of water. Anterior and posterior images were taken at 20 minute intervals over a 2 hour period. A geometric mean of activity pertaining to the gastric region was measured, and $T_{1/2}$ was calculated from the time activity curve. $T_{1/2}$ for normal the group was $57.8{\pm}6.3$ minutes while that for the AVH and CVH group was $58.2{\pm}8.2$ (p=0.40) and $64.1{\pm}10.5$ (p=0.09), respectively. There was 1 AVH Patient and 4 CVH patients with prolonged $T_{1/2}$. Anorexia and nausea was seen in 71% and 46% of the patients, respectively. 80% and 60% of the patients with prolonged $T_{1/2}$ had anorexia and nausea, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.635-643
• /
• 2017

The purpose of this study is to investigate the influence of the cold reduction rate and an ultrasonic fatigue test (UFT) on the fatigue behaviors of STS 304L. The tensile strength, yield strength, hardness value and fatigue limit in the UFT fatigue test linearly increased as thickness decreased from 1.5 mm to 1.1 mm, as the cold reduction rate of STS 304L increased. As a result of the UFT fatigue test (R = -1) of four specimens, the fatigue limit of the S-N curve formed a knee point in the region of $10^6$, and the 2nd fatigue limit caused by giga cycle fatigue did not appeared. In the case of t = 1.1 mm, the highest fatigue limit was 345 MPa, which was 64.3% higher than the original material (t = 1.5 mm). As a result of the UFT fatigue test of STS 304L, many small surface cracks occurred, grown, coalesced while tearing.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.162-173
• /
• 1996

Dry magnetic particle inspection(MPI) was performed to detect the surface defects of steel ingot cast billets. Magnetic properties of several materials were characterized by the measurement of the B-H hysteresis curve. The inspection results were evaluated in terms of the magnetizing current, temperature, and the amount of magnetic particles applied to billets. Magnetic flux leakage near the defect site of interest was measured and compared with the results of calculation by the finite element method in the case of direct magnetizing current. Direct and alternating magnetizing currents for materials were deduced by the comparison of the inspections. Results of the magnetic particle inspection by direct magnetizing current were compared with those of finite element method calculations, which were verified by measuring magnetic leakage flux above the surface and the surface defects of the material. For square rods, due to the geometrical effect, the magnetic flux density at the edges along the length of the rods was about 30% of that at the center of rod face for a sufficiently large direct magnetizing current, while it was about 70% for an alternating magnetizing current. Thus, an alternating magnetizing current generates rather uniform magnetic flux density over the rods, except for the region on the face across about 10 mm from the edge. The attraction of the magnetic particle by the magnetic leakage field was nearly independent of the surface temperature of the billets up to $150^{\circ}C$. However, the temperature should have been limited below $60^{\circ}C$ for an effective fixing of gathered magnetic particles to the billet surface using methylene chloride. We also found that the amount of applied magnetic particles tremendously affected the detection capability.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.714-721
• /
• 2013

A stoichiometric mixture of evaporating materials for $ZnAl_2Se_4$ single-crystal thin films was prepared in a horizontal electric furnace. These $ZnAl_2Se_4$ polycrystals had a defect chalcopyrite structure, and its lattice constants were $a_0=5.5563{\AA}$ and $c_0=10.8897{\AA}$.To obtain a single-crystal thin film, mixed $ZnAl_2Se_4$ crystal was deposited on the thoroughly etched semi-insulating GaAs(100) substrate by a hot wall epitaxy (HWE) system. The source and the substrate temperatures were $620^{\circ}C$ and $400^{\circ}C$, respectively. The crystalline structure of the single-crystal thin film was investigated by using a double crystal X-ray rocking curve and X-ray diffraction ${\omega}-2{\theta}$ scans. The carrier density and mobility of the $ZnAl_2Se_4$ single-crystal thin film were $8.23{\times}10^{16}cm^{-3}$ and $287m^2/vs$ at 293 K, respectively. To identify the band gap energy, the optical absorption spectra of the $ZnAl_2Se_4$ single-crystal thin film was investigated in the temperature region of 10-293 K. The temperature dependence of the direct optical energy gap is well presented by Varshni's relation: $E_g(T)=E_g(0)-({\alpha}T^2/T+{\beta})$. The constants of Varshni's equation had the values of $E_g(0)=3.5269eV$, ${\alpha}=2.03{\times}10^{-3}eV/K$ and ${\beta}=501.9K$ for the $ZnAl_2Se_4$ single-crystal thin film. The crystal field and the spin-orbit splitting energies for the valence band of the $ZnAl_2Se_4$ were estimated to be 109.5 meV and 124.6 meV, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that splitting of the ${\Delta}so$ definitely exists in the ${\Gamma}_5$ states of the valence band of the $ZnAl_2Se_4/GaAs$ epilayer. The three photocurrent peaks observed at 10 K are ascribed to the $A_1$-, $B_1$-exciton for n = 1 and $C_{21}$-exciton peaks for n = 21.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.271-272
• /
• 2012

Bulk Metallic Glasses (BMGs or amorphous alloy) exhibit high strength and good corrosion resistance. Applications of thin films and micro parts of BMGs have been used a lot since its inception in the research of BMGs. However, Application and fabrication of BMGs are limited to make structural materials. Thin films of BMGs which is sputtered on the surface of structural materials by sputtering process is used to improve limits about application of BMGs. In order to investigate the difference of properties between designed alloys and thin films, we identified that thin films deposited on the surface that have the characteristic of the amorphous films and the composition of designed alloys. Zr-Cu (Cu=30, 35, 38, 40, 50 at.%) and Zr-Cu-Al (Al=10 at.% fixed, Cu=26, 30, 34, 38 at.%) alloys were fabricated with Zr (99.7% purity), Cu (99.997% purity), and Al (99.99% purity) as melting 5 times by arc melting method before rods 2mm in diameter was manufactured. In order to analyze GFA (Glass Forming Ability), rods were observed by Optical Microscopy and SEM and $T_g$, $T_x$, ($T_x$ is crystallization temperature and $T_g$ is the glass transition temperature) and Tm were measured by DTA and DSC. Powder was manufactured by Gas Atomizer and target was sintered using powder in large supercooled liquid region ($=T_x-T_g$) by SPS(Spark Plasma Sintering). Amorphous foil was prepared by RSP process with 5 gram alloy button. The composition of the foil and sputtered thin film was analyzed by EDS and EPMA. In the result of DSC curve, binary alloys ($Zr_{62}Cu_{38}$, $Zr_{60}Cu_{40}$, $Zr_{50}Cu_{50}$) and ternary alloys ($Zr_{64}Al_{10}Cu_{26}$, $Zr_{56}Al_{10}Cu_{34}$, $Zr_{52}Al_{10}Cu_{38}$) have $T_g$ except for $Zr_{70}Cu_{30}$ and $Zr_{60}Al_{10}Cu_{30}$. The compositions with $T_g$ made into powders. Figure shows XRD data of thin film showed similar hollow peak.

• Journal of Broadcast Engineering
• /
• v.7 no.1
• /
• pp.45-54
• /
• 2002

This paper proposes a video compression algorithm using characteristics of wavelet coefficients. The proposed algorithm can provide lowed bit rate and faster running time while guaranteeing the reconstructed image qualify by the human virtual system. In this approach, each video sequence is decomposed into a pyramid structure of subimages with various resolution to use multiresolution capability of discrete wavelet transform. Then similarities between two neighboring frames are obtained from a low-frequency subband which Includes an important information of an image and motion informations are extracted from the similarity criteria. Four legion selection filters are designed according to the similarity criteria and compression processes are carried out by encoding the coefficients In preservation legions and replacement regions of high-frequency subbands. Region selection filters classify the high-frequency subbands Into preservation regions and replacement regions based on the similarity criteria and the coefficients In replacement regions are replaced by that of a reference frame or reduced to zero according to block-based similarities between a reference frame and successive frames. Encoding is carried out by quantizing and arithmetic encoding the wavelet coefficients in preservation regions and replacement regions separately. A reference frame is updated at the bottom point If the curve of similarity rates looks like concave pattern. Simulation results show that the proposed algorithm provides high compression ratio with proper Image quality. It also outperforms the previous Milton's algorithm in an Image quality, compression ratio and running time, leading to compression ratio less than 0.2bpp. PSNR of 32 dB and running tome of 10ms for a standard video image of size 352${\times}$240 pixels.

• Journal of Environmental Impact Assessment
• /
• v.22 no.3
• /
• pp.219-230
• /
• 2013

Species distribution modeling is one of the most effective habitat analysis methods for wildlife conservation. This study was for evaluating the suitability of species distribution to distance between forest patches in Seoul city using tits. We analyzed the distribution of the four species of tits: varied tit (Parus varius), marsh tit (P. palustris), great tit (P. major) and coal tit (P. ater), using the landscape indexes and connectivity indexes, and compared the resulting suitability indexes from 100m to 1,000m. As factors affecting to the distribution of tits, we calculated landscape indices by separating them into intra-patch indices (i.e. logged patch area (PA), area-weighted mean patch shape index (PSI), tree rate (TR)) and inter-patch indices (i.e. patch degree (PD), patch betweenness (PB), difference probability of connectivity (DPC)), to analyze the internal properties of the patches and their connectivity by tits occurrence data using logistic regression modeling. The models were evaluated by AICc (Akaike Information Criteria with a correction for finite sample sizes) and AUC (Area Under Curve of ROC). The results of AICc and AUC showed DPC, PA, PSI, and TR were important factors of the habitat models for great tit and marsh tit at the level of distance 500~800m. In contrast, habitat models for coal tit and varied tit, which are known as forest interior species, reflected PA, PSI, and TR as intra-patch indices rather than connectivity. These mean that coal tit and varied tit are more likely to find a large circular forest patch than a small and long-shaped forest patch, which are higher rate of forest. Therefore, different strategies are required in order to enhance the habitats of the forest birds, tits, in a region that has fragmented forest patches such as Seoul city. It is important to manage forest interior areas for coal tit and varied tit, which are known as forest interior species and to manage not only forest interior areas but also connectivity of the forest patches in the threshold distance for great tit and marsh tit as adapted species to the urban ecosystem for sustainable ecosystem management.