• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.856-858
• /
• 1999

The analysis of distribution line faults is essential to the proper protection of power system. A high impedance fault(HIF) dose not make enough current to cause conventional protective device. It is well known that undesirable operating conditions and certain types of faults on electric distribution feeders cannot be detected by using conventional Protection system. This paper describes an algorithm using neural network for pattern recognition and detection of high impedance faults. Wavelet transform analysis gives the time-scale information. Time-scale representation of high impedance faults can detect easily and localize correctly the fault waveform.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.474-475
• /
• 2008

Portable device is powered by the battery. To use portable devices longer time without replacing the battery, you should maximize the lifetime of the battery. If you use efficient DC-DC converter, You can maximize the lifetime of the battery.

• Current Optics and Photonics
• /
• v.5 no.6
• /
• pp.711-720
• /
• 2021

A novel optical hybrid device that doubles the multilevel demodulation resolution by adding the optical interferometer with a waveguide crossover is proposed, theoretically analyzed and experimentally verified. We report two types of all-passive phase control schemes that will be referred to as a phase compensation scheme and a phase optimization scheme. We also apply the proposed phase control schemes to a 45° optical hybrid consisting of two parallel 90° optical hybrids together with the proposed phase control scheme for demodulating 8-level differential phase shift keying optical signals. Octagonal phase response with low wavelength sensitive excess loss of <0.8 dB over 31-nm-wide spectral range will be demonstrated in the InP-based material platform.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.538-539
• /
• 2006

The influence of the internal current for the ZnO ceramics on the sintering behavior by pulse current sintering (PCS) method was investigated. To clear the dependence of inner current on the sintering behavior of ZnO ceramics, direct measurement of electric resistance of ZnO specimen under sintering by SPS device was carried out. It was observed that electric resistance of specimen decreases with increase in the temperature. The electric resistance begins to decrease from the low temperature of $200^{\circ}C$. The internal structure of sintered ZnO ceramics changed by the control of the internal current in the specimen using $Al_2O_3$ plate.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.97-100
• /
• 1999

AC to DC single phase PWM converter for traction application requires rated high power and voltage. Therefor, series or parallel operation converters are necessary with considering the limitation of the power device specification. This paper compares the characteristic between two parallel operation of conventional PWM converter and Single phase three level converter about comparison of power circuit, cooling system control method and harmonic current by computer simulation.

• Journal of Biomedical Engineering Research
• /
• v.41 no.6
• /
• pp.256-263
• /
• 2020

The importance of quality control has been emphasized to maintain safety of patients and satisfaction of medical service with medical devices used in clinic. Accordingly, objective evaluation method and standards consistently has been brought up for demand to replace outdated medical devices in appropriate time and to maintain the quality of medical service. Though many studies made suggestions methods to determine what medical devices to be replaced first, these methods were difficult in practice for its complex evaluation criteria and long time to evaluate. Therefore, in this study, a simple evaluation method is developed to identify and prioritize medical devices that are ought to be replaced. For the development of this simple evaluation method, four major characteristics of technology, safety, finance, and user satisfaction, which are considered in clinics to evaluate medical device replacement, and 14 minor attributes are distinctively selected. Each characteristic is assessed in binary form of "YES" or "NO" to minimize its subjective nature. Using this method to evaluate sampled medical devices belonging to four different characteristics, devices are suggested to be replaced in the current financial year or in the following financial year, or re-evaluated by the end of this financial year. Such results of evaluation can amend the subjective nature of existing evaluation method and give objective standards more promptly.

• Journal of Advanced Navigation Technology
• /
• v.15 no.5
• /
• pp.833-838
• /
• 2011

X-ray device used in the diagnosis has made possible to have more effective and accurate diagnosis, powered by the development of various devices. Based on this, X-ray device has become the most basic and essential diagnostic equipment in clinical medicine. At present, in the image acquisition field using X-ray, the use of Digital radiography which is useful in the acquisition time reduction and transfer of images and is possible to have the dose reduction has expanded. With the structure using one detector, this DR device has disadvantages in that it needs structural changes unlike existing X-ray and the detector should be moved to the desired position depending on the shooting location. Therefore, in this study, using BLDC(Brushless direct current) motor and PID(Proportional integral differential) control method, the automatic control system of 3-axis which is upward and downward, left and right and rotation of detector where having the most movement in DR was designed and produced and its performance was evaluated.

• Fire Science and Engineering
• /
• v.16 no.3
• /
• pp.8-11
• /
• 2002

Recently, the spark and the overheat due to in the failure of pressure contacts on connecting points and the momentary short circuit have been the major causes of electrical fire because these may cause the deposition and the graphite of insulating materials in electrical wiring system. Also, because in these cases the current is a surge one, the losses and faults of a communication, a home appliances, a computer and a measuring instrument may occur. Especially, in such cases, we are very difficult to detect the failure of pressure contacts on connecting points and the momentary short circuit. In this paper, we have developed an auxiliary control device, the electrical fire prevention control device(EFPCD), of an earth leakage breaker(ELB). And we can pre-vent the electrical fire caused by the spark and the overheat occurring in the failure of pressure contacts in connecting points and the momentary short circuit with the EFPCD.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.577-583
• /
• 2014

In this study, we introduce how to apply "Information and Communication Technology (ICT) to injection molding system. We report the current state of IT technology applied to produce their products in micro lens injection molding system. And we explain key technology of ICT for injection molding system and how to implement. Especially, we also mention about an embedded controller, also called as "M2M device". It provides programmable intelligent functions, communication, various interfaces, amplifier functions and mobile device connection to our application.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1201-1206
• /
• 2003

A measurement device for gas flow rate using hot-wire module is developed for the utilization in low-accuracy industrial applications. The module has three wires of measuring and heating, and a bridge circuit is installed to detect electric current through the wire in the module. An amplification of the signal and conversion to digital output are conducted for the online measurement with a personal computer. In addition, temperature distribution in the module is numerically analyzed to examine the measured outcome from the module experiment. The flow rate of air and carbon dioxide gas is separately measured for the performance examination of the device. The experimental relation of measurement and flow agrees with the prediction from the numerical analysis. The outcome of the performance test indicates that the accuracy and reproducibility of the module is satisfactory for the purpose of industrial applications.