• Journal of Sensor Science and Technology
• /
• v.31 no.5
• /
• pp.337-342
• /
• 2022

Hydrogen (H₂) gas is widely preferred for use as a renewable energy source owing to its characteristics such as environmental friendliness and a high energy density. However, H₂ can easily reverse or explode due to minor external factors. Therefore, H₂ gas monitoring is crucial, especially when the H₂ concentration is close to the lower explosive limit. In this study, metal oxide materials and their p-n heterojunctions were synthesized by a hydrothermal-assisted dip-coating method. The synthesized thin films were used as sensing materials for H₂ gas. When the H₂ concentration was varied, all metal oxide materials exhibited different gas sensitivities. The performance of the metal oxide gas sensor was analyzed to identify parameters that could improve the performance, such as the choice of the metal oxide material, effect of the p-n heterojunctions, and operating temperature conditions of the gas sensor. The experimental results demonstrated that a CuO/ZnO gas sensor with a p-n heterojunction exhibited a high sensitivity and fast response time (134.9% and 8 s, respectively) to 5% H₂ gas at an operating temperature of 300℃.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.842-844
• /
• 2004

Ternary tellurite glassy systems $(CuO-V_2O_5-TeO_2)$ have been synthesised using tellurium oxide as a network former and copper oxide as network modifier. The addition of a transition-matal oxide makes them electric or mixed electric-ionic conductors, which are of potential interest as cathode materials for solid-state batteries. This glass-ceramics crystallized from the $CuO-V_2O_5-TeO_2$ system are particularly interesting, because they exhibit high conductivity ( up to $6.03{\times}10^{-3}S/cm$) at room temperature. the glass samples were prepared by quenching the melt on the copper plate and the glass-ceramics were heat-treated at crystallizing temperature determined from differential thermal analysis (DTA). The electric D.C conductivity result have been analyzed in terms of a small polaron-hopping model.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2742-2746
• /
• 2023

The corrosion behavior of copper immersed in dilute oxychloride solution (100 mM) was studied through surface investigation and in-situ monitoring of open-circuit potential. The copper corrosion was initiated with copper dissolution into a form of CuCl^-₂, resulting in mass decrease within the first 40 h of immersion. This was followed by a hydrolysis reaction initiated by the CuCl^-₂ at the copper surface, after which oxide products were formed and deposited on the surface, resulting in a mass increase. The formation of nucleation sites for copper oxide and its lateral extension during the corrosion process were examined using focused ion beam (FIB)-scanning electron microscopy (SEM). The presence of metastable compounds such as atacamite (CuCl₂·3Cu(OH)₂) on the corroded copper surface was revealed by X-ray photoelectron spectra (XPS) and transmission electron microscopy (TEM)-energy dispersive spectrometry (EDS) analysis.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.220-220
• /
• 2003

최근, Cu기판 위에 YBaCuO$_{7-x}$ 초전도체를 입혀 초전도 선재를 제작하려는 연구가 이루어지고 있으며 이 과정에서 CuO와 Cu$_2$O가 생성된다는 보고가 있다. CuO 및 Cu$_2$O의 생성은 초전도 선재의 전기전도적 특성 및 기계적 특성에 상당한 영향을 끼칠 수 있다. 따라서 CuO와 Cu$_2$O에 대한 연구가 필요하다고 할 수 있다. 본 연구에서는 DV-X$\alpha$ 분자궤도법을 통해 CuO와 Cu$_2$O에 대한 (Cu$_{29}$ O$_{58}$ )$^{58-}$ , (Cu$_{52}$ O$_{19}$ )$^{14+}$ 모델을 이용하여 전자상태계산을 하였다. CuO, Cu$_2$O의 valence orbital level 구조 및 DOS (Density of State)를 통해 Cu원자와 O원자간의 공유결합 세기를 측정하였으며 CuO, Cu$_2$O 서로간의 차이점을 분석하였다.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.8
• /
• pp.1561-1564
• /
• 2008

Although the use of Cu(II) salts as catalysts without reductants is limited in the cycloaddition of acetylenes with azides, the catalytic system employing average 10 nm CuO(II) nanoparticles in the absence of reductants shows good catalytic activity to form 1,4-disubstituted 1,2,3-triazoles even in wet THF as well as water. It is also noticeable that CuO(II) nanoparticle catalysts can be recycled with consistent activity. A range of alkynes and azides were subject to the optimized CuO(II) nanoparticle-catalyzed cycloaddition reaction conditions to afford the desired products in good yields.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.282-284
• /
• 2007

The superconductor characteristics of BSCCO spray films by Heat treatment was studied. $Bi_2Sr_2CaCu_2O_x$(Bi-2212) is high-Tc superconductor(HTS) coatings have been prepared by Heat treatment. Where high current carrying capabilities are required and therefore thick film and bulk material are called for, the Bi2Sr2Ca1Cu2O8-d(Bi-2212)compound has evoleved as one of the most promising. and the Bi-2212 HTS coating layer is synthesized through the peritectic reaction between Sr-Ca-Cu oxide coating layer and Bi-Cu oxide coating layer by partial melting process. The superconducting characteristics depends on the spray distance which was related to the spray particle melt. The Bi-2212 HTS layer consists of the whisker growth and secondary phase in 2212 layer were observed.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.9
• /
• pp.908-912
• /
• 1991

YBaCuO oxide superconductor-shows superconductive at Liquid Nitrogen temperature-must be preparate wire or thin film form for utility. The wiring is possible with heat treatment after appropriate mixture of polymeric binder and YBaCuO oxide superconductor has fabricated. This study, analyzed the characteristics of fabricated superconductor and extruded wire after application to each of a mixed at different rate in the superconductor and compared with an original pure sample. From the result, we knew that the binder component influences superconducting characteristics. The best condition for superconductivity occurred at a criticla temperature of 86.4K (8:2 rate) and at a critical current density of 100.27A/cmy with a binder packing ratio of about 20~25 percent.

• Electrical & Electronic Materials
• /
• v.9 no.4
• /
• pp.357-363
• /
• 1996

The superconducting properties of YBa$_{2}$Cu$_{3}$$O_{7-x}$(YBaCuO) thin films prepared by laser ablation have been investigated. The x-ray diffraction patterns of the films were substantially different from one another. The Y and Ba oxides are formed by the collisions with oxygen molecules. On the other hand, the Cu oxide is mainly formed at initial stage of the laser irradiation. The YBaCuO films manufactured on MgO(100) substrate were indicated T$_{c}$(zero)=90 K, T$_{c}$(onset)=92 K, and J$_{c}$=3.5*10$^{5}$ A/cm$^{2}$(at 77.3K). The optimum conditions were found to be a substrate temperature of 710.deg. C, an energy density of 2 J/cm$^{2}$, and a target-substrate distance of 60mm in an oxygen partial pressure of 200 mTorr.0 mTorr.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.1
• /
• pp.51-54
• /
• 2009

Transparent Cuprous oxide film was deposited by rapid thermal oxidation (RTO) of Cu at $500^{\circ}C$/45s condition on textured single-crystal n-Si substrate to form $Cu_2O$/n-Si heterojunction photodiode. The Hall effect measurements for the $Cu_2O$ films showed a p-type conductivity. The photovoltaic and electrical properties of the junction at room temperature were investigated without any post-deposition annealing. I-V characteristics revealed that the junction has good rectifying properties. The C-V data showed abrupt junction and a built-in potential of 1 V. The photodiode showed good stability and high responsivity in the visible at three regions; 525 nm, 625-700 nm, and 750nm denoted as regions A, B, and C, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.1-12
• /
• 1999

Brown oxide and/or black oxide layers were formed on the surface of Cu-based leadframe by chemical oxidation of leadframe in hot alkaline solutions, and their growth characteristics were studied. Then, to measure the adhesion strength between leadframe and epoxy molding compound (EMC), oxidized leadframe samples were molded with EMC and machined to form sandwiched double-cantilever beam (SDCB) specimens and pull-out specimens, respectively. Results showed that the adhesion strength of un-oxidized leadframe/EMC interface was inherently very poor but could be increased drastically with the nucleation of acicular CuO precipitates on the surface of leadframe. The presence of smooth faceted $Cu_2O $ on the surfaces of leadframe gave close to zero interfacial fracture toughness (Gc) and reasonable pull strength (PS). A direct correlation between Gc and PS showed that PS can be a measure of Gc only in a limited range.