• Bulletin of the Korean Chemical Society
• /
• v.20 no.3
• /
• pp.291-296
• /
• 1999

The immobilization of APTMS(3-(2-aminoethylamino)propyltrimethoxysilane) and AAPTMS(3-(2-(2-aminoethyl)aminoethylanino)propyltrimethoxysilane) on the surface of high quality mesoporous molecular sieves MCM-41 and MCM-48 have been confirmed by F.T.-IR spectroscopy, Raman spectroscopy, 29Si solid state NMR, and a surface polarity measurement using Reichardt's dye. The formation of metal (Co(Ⅱ), Ni(Ⅱ), and Cu(Ⅱ)) complexes by immobilized aminosilanes have been investigated by photoacoustic spectroscopy(PAS). The assignment of UV-Vis. PAS bands makes it possible to identify the structure of metal complexes within mesoporous molecular sieves. Co(Ⅱ) ion may be coordinated mainly in a tetrahedral symmetry by two APTMS onto MCM-41, and in an octahedral one by two AAPTMS. Both Ni(Ⅱ) and Cu(Ⅱ) coordinated by aminosilanes within MCM-41 form possibly the octahedral complexes such as [Ni(APTMS)2(H20)2]2+, [Ni(AAPTMS)2]2+, [Cu(APTMS)2(H2O)2]2+, and [Cu(AAPTMS)(H2O)3]2+, respectively. The PAS band shapes of complexes onto MCM-48 are similar to those of corresponding MCM-41 with the variation of PAS intensity. Most of metal ion(Ⅱ) within MCM-41 and MCM-48 are coordinated by aminosilanes without the impregnation on the surface.

• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.1040-1046
• /
• 1995

The formation free energy of Y2Cu2O5 was measured by the partial ion exchanged (Cu2+, Na+)-$\beta$/$\beta$"-Al2O3 as solid state electrolyte. The formation cell was built as follows: Pt(O2)/Y2Cu2O5＋Y2O3//(Cu2+, Na+)-$\beta$/$\beta$"-Al2O3//CuO/(O2)Pt The virtual formation formation formula, and the calculated formation free energy of Y2Cu2O5 as a function of temperature are as follows: 2CuO＋Y2O3=Y2Cu2O5 ΔfG0/kJ.mol-1=13.19-16.25*10-3T/K.5*10-3T/K.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.429-434
• /
• 2001

Ti-Cu-N nanocomposite films deposited by arc ion plating and magnetron sputter hybrid system with various copper contents. The microstructure and mechanical properties of Ti-Cu-N superhard nanocomposite films depend on the Cu concentration. In X-ray diffraction (XRD) analysis, intensity of TiN (111) and TiN (220) peak decreased and peak broadness increased with increasing the copper contents and Cu peak was not detected. The grain size of films decreased with increasing at%Cu and Transmission Electron Microscopy (TEM) analysis also showed that Ti-Cu-N film containing 1.5at%Cu was composed of very fine (<10nm) nanocrystalline grains. The maximum hardness of Ti-Cu-N (1.5at%Cu) film reached to 45GPa and friction coefficient was measured 0.3.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.165-168
• /
• 2000

We fabricated ramp-edge Josephson junctions with barriers formed by interface treatments instead of epitaxially grown barrier layers. A low-dielectric Sr$_2$AlTaO$_6$(SAT) layer was used as an ion-milling mask as well as an insulating layer for the ramp-edge junctions. An ion-milled YBa$_2$Cu$_3$O$_{7-x}$ (YBCO)-edge surface was not exposed to solvent through all fabrication procedures. The barriers were produced by structural modification at the edge of the YBCO base electrode using high energy ion-beam treatment prior to deposition of the YBCO counter electrode. We investigated the effects of high energy ion-beam treatment, annealing, and counter electrode deposition temperature on the characteristics of the interface-controlled Josephson junctions. The junction parameters such as T$_c$, I$_c$c, R$_n$ were measured and discussed in relation to the barrier layer depending on the process parameters.

• Macromolecular Research
• /
• v.16 no.1
• /
• pp.21-30
• /
• 2008

Based on the sheath-core bicomponent composite fibers with modified polystyrene (PS) and the modified polypropylene (PP), composite fibers obtained were further cross-linked and sulphonated with chlorosulphonic acid to produce strong acidic cation ion exchange fibers. The structures of the fibers obtained were characterized using Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC) etc. The optimal technology of the fibers obtained is discussed. The static absorption capacity of the sheath-core bicomponent composite cation exchange fibers for $Zn^{2+}$, $Cu^{2+}$ was determined. The absorption kinetics and major factors affecting the absorption capacities of $Zn^{2+}$, $Cu^{2+}$ were studied, and its chemical stability and regenerating properties were probed. The results suggest that cation exchange fibers with better mechanical properties and higher exchange capability were obtained. Moreover, this type of ion exchange fiber has good absorption properties and working stability to various metal ions. Hence, they have higher practicability.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.524-527
• /
• 2007

[ $Bi_2Sr_2Ca_{n-1}Cu_nO_x$ ](n=0, 1, 2) thin films have been fabricated by co-deposition at an ultra-low growth rate using ion beam sputtering(IBS) method. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about % K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $ CaCuO_2$ was observed in all of the obtained films.

• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.23-28
• /
• 1997

The adsorption characteristics of ammonia-Cu(II) complex on activated carbon were studied. Firstly, the specific surface area of the activated carbon was measured by using the BET adsorption apparatus. Secondly, the characteristics of the removal copper(II) ion from aqueous ammonia solution by forming a complex with ammonia and then by the adsorption of the complex on the activated carbon were studied. It was found that the specific surface area increases with decreasing the mesh number of the activated carbon, and the optimum pH for the adsorption of the Cu(II) ion on she activated carbon was found to be approximately 6. It was also found that the adsorbed Cu(II)-ammonia complexes on the activated carbon in the aqueous ammonia solution have two types, depending on the concentration of the solution ; i.e. $[Cu(NH_3){_2}]^{2+}$and $[Cu(NH_3){_3}]^{2+}$ for $2.25{\times}10^{-4}(mol/{\ell})$and $2.25{\times}10^{-3}(mol/{\ell})$, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.6
• /
• pp.1115-1121
• /
• 2007

[ $Bi_2Sr_2Ca{_{n-1}}Cu_nO_x$ ](n=0,1,2) thin fans have been fabricated by co-deposition at an ultra-low growth rate using ion beam sputtering(IBS) method. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about 90 K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $CaCuO_2$ was observed in all of the obtained films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.624-627
• /
• 2001

Two kinds of Nd$_{1+x}$Ba$_{2-x}$Cu$_3$O$_{7-{\delta}}$, the sintering samples and zone melting samples, were heat treated under pure Ar at 95$0^{\circ}C$. The substitution of Nd ion for Ba ion in the Nd$_{1+x}$Ba$_{2-x}$Cu$_3$O$_{7-{\delta}}$ before and after the heat treatment were investigated by XRD. In order to know the effects of the heat treatment, the T$_{c}$ and J$_{c}$ of samples with the heat treatment and those without the heat treatment by Ar were comparatively studied. The results show that the substitution of Nd for Ba decreased, T$_{c}$, and J$_{c}$ increased after the treatment under Ar at 95$0^{\circ}C$. The Nd$_{1+x}$Ba$_{2-x}$Cu$_3$O$_{7-{\delta}}$ samples were oxygenated under pure oxygen at 30$0^{\circ}C$. From the XRD pattern it was found that the sample with x< 0.4 could transfer from tetragonal phase to orthorhombic phase after the oxygenation, but the sample with x>0.4 could not make the phase transition even after a long time oxygenation.ion even after a long time oxygenation.ation.n.ation.ation.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.12-20
• /
• 2022

The smelting reduction of spent lithium-ion batteries results in metallic alloys containing Co, Cu, Fe, Mn, Ni, and Si. A process to separate metal ions from the sulfuric acid leaching solution of these metallic alloys has been reported. In this process, ionic liquids are employed to separate Fe(III) and Cu(II). In this study, D2EHPA and Cyanex 301 were employed to replace these ionic liquids. Fe(III) and Cu(II) from the sulfate solution were sequentially extracted using 0.5 M D2EHPA with three stages of cross-current and 0.3 M Cyanex 301. The stripping of Fe(III) and Cu(II) from the loaded phases was performed using 50% (v/v) and 60% (v/v) aqua regia solutions, respectively. The mass balance results from this process indicated that the recovery and purity percentages of the metals were greater than 99%.