• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.518-522
• /
• 2013

This study investigatesthe coloration mechanism by identifying the factor that affects thered coloration of copper red glazesin traditional Korean ceramics. The characteristics of the reduction-fired copper red glaze's sections are analyzed using an optical microscope, Raman spectroscopy, scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDX). The sections observed using an optical microscope are divided into domains of surface, red-bubble, and red band. According to the Raman micro spectroscopy analysis results, the major characteristic peak is identified as silicate in all three domains, and the intensity of $Cu_2O$ increases toward the red band. In addition, it is confirmed that the most abundant CuO exists in the glaze bubbles. Moreover, CuO and $Cu_2O$ exist as fine particles in a dispersed state in the surface domain. Thus, Cu combined with oxygen is distributed evenly throughout the copper red glaze, and $Cu_2O$ is more concentrated toward the interface between body and glaze. It is also confirmed that CuO is concentrated around the bubbles. Therefore, it is concluded that the red coloration of the copper red glaze is revealed not only through metallic Cu but also through $Cu_2O$ and CuO.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.256-256
• /
• 2010

투명전극부터 디스플레이 산업에 이르기까지 광범위하게 응용되어지고 있고 개발되어지고 있는 투명전도산화물(TCO)은 ZnO, In2O3, SnO2 등을 기본으로 하는 n-type 재료가 대부분이다. 그러나 투명전도 산화물을 이용한 light emitting diode(LED), 투명한 태양전지, p-형 TFT와 같은 투명전자소자의 개발을 위해서는 p-type 소재가 필수적이다. p-type TCO 소재는 비교적 연구 개발 실적이 매우 부진한 실정이었다. 1997년 넓은 밴드갭을 가지는 ABO2(delafossite) 산화물이 p-type으로서 안정적이라는 것을 보고함에 따라 이에 대한 연구가 활발히 진행되고 있다. 현재 ABO2 형태를 가진 Delafossite구조 산화물이 가장 유망한 p-type 투명전도체 소재로 거론되고 있다. Delafossite 구조가 p-type 투명전도체에 적합한 결정구조인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. Delafossite구조는 상온에서 2종류의 polytype(상온에서 Rhombohedaral구조와 hexagonal 구조)이 존재하며 이들은 각각 3R 및 2H의 결정 구조를 가지고 있다. ABO2의 delafossite구조에서 Cu+의 배열은 c-축을 따라 Cu-O-Cr-O-Cu의 연속적인 층 구조로서 2차원연결로 보여 진다. 보고된 Cu- base delafossite구조를 가지는 재료들은 CuAlO2, CuGaO2, CuInO2 등 여러가지가 있다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Zn를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 산소분압을 $500{\sim}700^{\circ}C$, 0~10mTorr로 변화시켜 특성을 연구하였다. 성장온도 $700^{\circ}C$, 산소분압 10mTorr에서 c-plane 사파이어 기판위에 c-축 배향의 에피성장된 CuCrO2:Zn 박막을 얻을 수 있었다. Mg를 도핑함에 따른 p-type 특성보다 현저히 떨어지는 것을 확인하였다. 또한 동일한 조건임에도 특정한 이차상의 존재를 통해 도핑된 Zn의 위치를 추측할 수 있었다. 온도와 분압에 따른 결정성과 표면상태를 SEM을 통해서 확인하였다.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.1
• /
• pp.5-8
• /
• 1989

Conventional ceramic method has been used to prepare the green phase, $Y_2BaCuO_5$, commonly observed in 90-K superconductor $YBa_2Cu_3O_P{7-{\delta}}$as an impurity phase. The powder X-ray diffraction analysis indicates that $Y_2BaCuO_5$ has an orthorhombic symmetry with lattice parameter of a = 12.2 $\AA$, b = 5.61 $\AA$, and c = 7.14 $\AA.$ The average g-value 2.13 observed in ESR spectrum is attributable to Cu2+ stabilized in $C_{4v}$ field. From the magnetic susceptibility ($\mu$eff = 2.29 BM) and the ESR measurements, it is confirmed that Cu(II) $3d^9$ electrons in $Y_2BaCuO_5$ are localized and can be characterized by Curie-Weiss behavior. Optical reflectance spectrum shows a broad absorption peak around 680 nm due to dxy ${\rightarrow}$ $dx^2-y^2$ eletronic transition.

• The Korean Journal of Pharmacology
• /
• v.23 no.1
• /
• pp.25-31
• /
• 1987

The present study examines firstly, the inhibition of collagen gelation to explore the possible involvement of $Cu^{++}$-catalyzed peroxidation in rheumatoid arthritis and secondly, the effect of sodium salicylate on this peroxidative reaction to provide a possible explanation for its mechanism of anti-inflammatory action. Incubation of collagen obtained from rat skin with $Cu^{++}$ and $H_2O_2$ resulted in the inhibition of gelation in terms of maximal turbidity and lag phase, but either $Cu^{++}$ or $H_2O_2$ alone essentially gave no effect in the collagen gelation. In the presence of sodium salicylate the inhibited gelation of collagen induced by $Cu^{++}$ and $H_2O_2$ was reversed with the dependency of the concentration of sodium salicylate. Moreover, the rate of $H_2O_2$ decomposition by $Cu^{++}$ was accelerated by sodium salicylate and this decomposition of $H_2O_2$ was found to be saturable in terms of concentration of this drugs. Thus it can be expected that $Cu^{++}$ -catalyzed peroxidation attacks collagen resulting in change of structural or functional integrity of collagen, and sodium salicylate may act on this peroxidative process, possibly through the enhancement of catalatic action of $Cu^{++}$. From these results $Cu^{++}$-catalyzed peroxidation can be in part responsible for degradation of joint tissue in rheumatoid arthritis and sodium salicylate may exert its anti-inflammatory action by this peroxidative reaction.

• Applied Chemistry for Engineering
• /
• v.27 no.2
• /
• pp.145-152
• /
• 2016

In this study, CuO was introduced on MWCNTs dispersed with Au nanoparticles to improve the glucose sensing capability of electrochemical biosensors. Nano-cluster shaped CuO was synthesized due to the presence of Au nanoparticle, which affects glucose sensing performance. The biosensor featuring CuO/Au@MWCNTs nanocomposite as an electrode material when 0.1 mole of CuO was synthesized showed the highest sensitivity of $504.1{\mu}A\;mM^{-1}cm^{-2}$, which is 4 times better than that of MWCNTs based biosensors. In addition, it shows a wider linear range from 0 to 10 mM and lower limit of detection (LOD) of 0.008 mM. These results demonstrate that CuO/Au@MWCNTs nanocomposite sensors are superior to other CuO based biosensors which are attributed that the nano-cluster shaped CuO is favorable for the electrochemical reaction with glucose molecules.

• Journal of Powder Materials
• /
• v.16 no.4
• /
• pp.280-284
• /
• 2009

The pressureless sintering behavior of $Al_2O_3$/Cu powder mixtures, prepared from $Al_2O_3$/CuO and $Al_2O_3$/Cu-nitrate, has been investigated. Microstructural observation revealed that $Al_2O_3$ powders with nano-sized Cu particles could be synthesized by hydrogen reduction method. The specimens, pressureless-sintered at $1400^{\circ}C$ for 4 min using infrared heating furnace with the heating rate of $200^{\circ}C$/min, showed the relative density of above 90%. Maximum hardness of 16.1 GPa was obtained in $Al_2O_3$/MgO/Cu nanocomposites. The nanocomposites exhibited the enhanced fracture toughness of 4.3-5.7 $MPa{\cdot}m^{1/2}$, compared with monolithic $Al_2O_3$. The mechanical properties were discussed in terms of microstructural characteristics.

• Journal of Korea Foundry Society
• /
• v.5 no.3
• /
• pp.19-26
• /
• 1985

This study has been carried out to examine into wettability of Cu-5%Sn alloy in $Al_2O_3$, MgO, $SiO_2$ and graphite, respectively and investigated into the change in macrostructure of Cu-5%Sn alloy according to kind and mixing rate of mold-coating. The results obtained from the experiment are summerized as follows; 1. Cu Cu-5%Sn alloy, wettabilities of $Al_2O_3$ and MgO were good, on the other hand, wettabilities of $SiO_2$ and graphite were bad. 2. The fine equiaxed zone was created because of the role of $Al_2O_3$ and MgO as preferential nucleation sites. 3. Notwithstanding change of mixing rate of $SiO_2$ in mold coating the equixed zone was not created. 4. The area of equiaxed zone was varied according to mixing rate in the case of using $Al_2O_3$ and MgO in mold-coating.

• Clean Technology
• /
• v.9 no.4
• /
• pp.189-196
• /
• 2003

ZnO-CuO mixed sorbents for desulfurization in hot gas cleaning process Were prepared and investigation on their characteristics was performed in this study. The rate of sulfidation increased as the amount of copper oxide in the composite sorbent was raised. TPO experiments were carried out to investigate the characteristics of the regeneration of the sorbents with severa1 different ratios of Zno to CuO. Copper sulfate was formed at temperatures above $400^{\circ}C$, while it was decomposed by pyrolysis above $700^{\circ}C$. $SO_2$ slippage due to $CuSO_4$ was observed in the sorbent regenerated at temperatures above $600^{\circ}C$. However, it was not observed when regenerated above $700^{\circ}C$. It was confirmed in the ZnO-CuO mixed sorbent system that CuO suppressed the vaporization of ZnO on the one hand and Zno minimized the $SO_2$ slippage due to CuO on the other hand.

• Journal of Environmental Science International
• /
• v.14 no.7
• /
• pp.669-674
• /
• 2005

Catalytic combustion of toluene was investigated on $CuOx/SnO_2-ZrO_2\;CuOx/SnO_2\;CuOx/ZrO_2$ catalysts prepared by impregnation. Characteristics of catalysts loaded on binary support and single support were observed by TPR, TPO, XRD, XPS techniques. The results on catalytic combustion showed that binary supports improve the activity of copper in the combustion of toluene. The reason for high catalytic activity on toluene combustion of $CuOx/SnO_2-ZrO_2$ catalyst was ascribed to oxidation$\cdot$reduction activity at low temperatures and stability of oxidation state after reduction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.1
• /
• pp.38-42
• /
• 2005

B$_2$O$_3$ added Ba(Mg$_{1}$3/Nb$_{2}$3/)O$_3$ (BBMN) ceramics were not sintered below 900 $^{\circ}C$. However, when CuO was added to the BBMN ceramic, it was sintered even at 850 $^{\circ}C$. The amount of the $Ba_2$B$_2$O$_{5}$ second phase decreased with the addition of CuO. Therefore, the CuO additive is considered to react with the B$_2$O$_3$ inhibiting the reaction between B$_2$O$_3$ and BaO. Moreover, it is suggested that the solid solution of CuO and B$_2$O$_3$ might be responsible for the decrease of the sintering temperature of the specimens. A dense microstructure without pores was developed with the addition of a small amount of CuO. However, a porous microstructure with large pores was formed when a large amount of CuO was added. The bulk density, the dielectric constant ($\varepsilon$$_{r}$) and the Q-value increased with the addition of CuO but they decreased when a large amount of CuO was added. The variations of those properties are closely related to the variation of the microstructure. The excellent microwave dielectric properties of Qxf = 21500 GHz, $\varepsilon$$_{r}$ = 31 and temperature coefficient of resonance frequency($\tau$$_{f}$) = 21.3 ppm/$^{\circ}C$ were obtained for the Ba(Mg$_{1}$3/Nb$_{2}$3/)O$_3$+2.0 mol%B$_2$O$_3$+10.0 mol%CuO ceramic sintered at 875 $^{\circ}C$ for 2 h.h.2 h.h.