• 한국인터넷방송통신학회논문지
• /
• 제16권3호
• /
• pp.179-186
• /
• 2016

본 연구는 차량의 도로이탈을 방지하고, 충격량을 흡수하여 차량 탑승자 및 도로주변의 인도를 횡단하는 보행자를 보호하기 위한 차량용 방호울타리에 관한 연구로서 LS-DYNA를 이용해 탑승자 보호성능 평가시험을 시뮬레이션하였으며, 다양한 속도와 각도를 변경하여 반복 시뮬레이션을 하여 충돌조건에 따른 탑승자 보호성능을 고찰하였다. 시뮬레이션을 위한 변수의 설정은 국내차량 판매대수에 따른 평균차량의 중량을 구하고, 미국 NHTSA의 NASS를 분석하여 실제 사고가 발생하는 속도와 충돌각도구간을 검출하였다. 그 결과로 충돌속도와 충돌각도가 커질수록 THIV(탑승자 충격속도)와 PHD(탑승자 가속도) 값이 증가하는 것을 확인하였으며, 차량이 가드레일의 지주에 걸리는 현상이 발생할 때 탑승자보호성능이 크게 저하되는 것을 확인하였다.

• 한국지진공학회논문집
• /
• 제27권5호
• /
• pp.193-202
• /
• 2023

In this paper, a dynamic centrifuge model test was conducted on a 24.8-meter-deep excavation consisting of a 20 m sand layer and 4.8 m bedrock, classified as S3 by Korean seismic design code KDS 17 10 00. A braced excavation wall supports the hole. From the results, the mechanism of seismically induced earth pressure was investigated, and their distribution and loading points were analyzed. During earthquake loadings, active seismic earth pressure decreases from the at-rest earth pressure since the backfill laterally expands at the movement of the wall toward the active direction. Yet, the passive seismic earth pressure increases from the at-rest earth pressure since the backfill pushes to the wall and laterally compresses at it, moving toward a passive direction and returning to the initial position. The seismic earth pressure distribution shows a half-diamond distribution in the dense sand and a uniform distribution in loose sand. The loading point of dynamic thrust corresponding with seismic earth pressure is at the center of the soil backfill. The dynamic thrust increased differently depending on the backfill's relative density and input motion type. Still, in general, the dynamic thrust increased rapidly when the maximum horizontal displacement of the wall exceeded 0.05 H%.

• 자동차안전학회지
• /
• 제3권2호
• /
• pp.22-27
• /
• 2011

The side impact test in the Korean New Car Assessment program (KNCAP) has been conducted since 2003. The side impact test method has been contributed to the improvement of the vehicle side structure and the enhancement of the occupant protection performance for the domestic vehicles. The pole side impact test method introduced in the KNCAP in 2010 to enhance the head protection under the severe side crash environment. The pole side impact test is optional for the additional score to be added to the overall rating score. The test results of side and pole side impact test for five vehicles were introduced and compared.

• 대한인간공학회지
• /
• 제21권2호
• /
• pp.13-23
• /
• 2002

Human dummies are essential tools in the development of such products as vehicle have been actively used not only in reach and view field tests. but also in impact perception evaluations. This study attempted to obtain geometric and dynamic model body segments from Korean anthropometric data. The investigation focused on the de both human and dummy for the geometric and inertial properties. The dynamic modeli being suggested is based on rigid body dynamics using fifteen individual body segments by joins. The segments are connected at the locations representing the physical joint body so that each segment has its mass and moment of inertia. For visual three-dimensional graphic was used for easier implementation of the dumn applications. For applications, proposed Korean dummies Were used in dynamic crash and driver's view and reach test modules were developed in virtual environment.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.155-160
• /
• 2003

For the weight reduction of vehicle body up to 20∼30% compared to the conventional monocoque steel body·.in-white, most automotive manufacturers have attempted to develop the aluminum intensive body-in-white using an aluminum space frame. In this paper, the crush tests and simulations for the aluminum extrusions filled with the structural from are performed to evaluate the collapse characteristics of that light weighted material. From these studies. the effectiveness of structural for is evaluated in improving automotive crashworthiness. In order to improve the improve energy absorption capability of the aluminum space frame body, safety design modifications are performed and analyzed based on the suggested collapse initiator concepts and on the application of the aluminum extrusions filled with structural foam. The effectiveness of these design concepts on the frontal and side impact characteristics of the aluminum intensive vehicle structure is investigated and summarized.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.135-142
• /
• 2007

MADYMO human model with the detail neck was used to investigate the reaction force of neck and neck injury from rear impact directions. In the validation simulation, head acceleration, thorax acceleration and the global kinematics of the head and neck were correlated well with experimental data. Acceleration data from three 15 km/h low speed car rear impact pendulum tests(rear-end, offset, oblique) were used to simulate the model. In the simulation results, the reaction force on the facet joint and discs in the oblique rear impact were higher than rear-end, offset rear impacts. Further research is still needed in order to neck injury analysis about different crash parameters.

• International Journal of Automotive Technology
• /
• 제5권3호
• /
• pp.173-180
• /
• 2004

An intensive study was conducted for the crash worthy structural design of the recently developed Korean High Speed Train (KHST). Two main design concepts were set up to protect both crews and passengers from serious injury in heavy collision accidents, and to reduce damage to the train itself in light collision accidents. A collision against a movable 15-ton rigid obstacle at 110 kph was selected from train accident investigations as the accident scenario for the heavy collisions. A train-to-train collision at the relative velocity of 16 kph was used for the light collision. The crashworthiness behaviors of KHST were numerically evaluated using FEM. Analysis results using 1-D collision dynamics model of the full rake consist and 3-D shell element model of the front end structure showed good crashworthy responses in a viewpoint of structural design. Occupant analyses and sled tests demonstrated that KHST performed well enough to protect occupants under the considered accident scenarios. Finally our numerical approaches were evaluated by a real scale collision test.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.322-327
• /
• 2004

This paper describes the structural analysis result of accident EMU(Electric Multiple Units). Structural analysis of EMU was performed for the criteria of safety assessment. Structural analysis using commercial I-DEAS software provided important information on the stress distribution and load transfer mechanisms as well as the amount of damages during rolling stock crash. Tensile tests were performed on two different types of specimens in order to evaluate the strength changes before and after damages, obtained from plastic deformed area and nondeformed region of the accident EMU. The structural analysis and tensile test results have been used to provide the critical information for the criteria of safety assessment.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.143-148
• /
• 2000

This paper describes how to make tailored blanks of front side member that were composed of high strength steel and TRIP(TRansformation Induced Plasticity) steel for weight reduction and improvement of crash load. Tailored blanks made by laser and mash-seam welding were compared with non-tailored blanks made by spot welding. Static compression tests were performed for performance comparison of each sample. Front side members made by tailored blank were superior to those made by spot welding in the initial, but those results were inverse in the last. Average load of tailored blank in six-angle type was better than that of rectangular type.

• 소성∙가공
• /
• 제10권3호
• /
• pp.200-205
• /
• 2001

This paper describes how to make tailored blanks of front side member that were composed of high strength steel and TRIP(TRansformation Induced Plasticity) steel for weight reduction and improvement of crash load. Tailored blanks made by laser and mash-seam welding were compared with non-tailored blanks made by spot welding. Static compression tests were performed for performance comparison of each sample. Front side members made by tailored blank were superior to those made by spot welding in the initial, but those results were inverse in the last. Average load of tailored blank in six-angle type was better than that of rectangular type.