• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1334-1340
• /
• 2001

In this paper, the experimental modeling of the force between permanent magnet and iron-core solenoid is suggested for more accurate control of 3 D.O.F. motor using the electromagnetic force. In the case of iron-core solenoid, the general equation of solenoid cant be used simply because of its nonlinearity. Therefore, the magnetic flux density is estimated through the concept of equivalent permanent magnet. The force distribution between permanent magnet and iron-core solenoid is more dependent on the magnetization of iron core caused by the permanent magnet than any other parameters. Therefore, the equation of the force estimation between these magnetic systems can be modeled by the experimental function of the magnetization of iron core. Especially, if the distance between iron-core solenoid and permanent magnet is far enough, the force equation through experiment can be expressed from only the current of coil and the distance between iron-core solenoid and permanent magnet. It means that Coulombs law can be used for magnetic systems and it is validated through the experiment. Therefore, force calibration is performed by the concept of Coulombs law.

• 한국기계가공학회지
• /
• 제15권4호
• /
• pp.60-66
• /
• 2016

This study used an ultrasound infrared thermography technique to detect issues in the motor core of typical power equipment. The current defect inspection method of the motor core is often incomplete (due to the limits of visual inspection) and thus the reliability of the motor core is reduced. Therefore, in this study, experiments were carried out to increase the reliability of the test by using an ultrasonic infrared thermal non-destructive inspection method to image the motor core. The ambient temperature of the experimental system was maintained at $25^{\circ}C$. Experiments were carried out to examine a damaged motor core and a defect-free motor core. Experimental results confirm the technique clearly detected defects in the motor core, thereby confirming the possibility of using this technique in the field.

• Earthquakes and Structures
• /
• 제16권5호
• /
• pp.589-599
• /
• 2019

Conventional buckling restrained braces used in concentrically braced frames are expected to yield in both tension and compression without major degradation of capacity under severe seismic ground motions. One of the weakness points of a standard buckling restrained braced frame is the low post-yield stiffness and thus large residual deformation under moderate to severe ground motions. This phenomenon can be attributed to low post-yield stiffness of core member in a BRB. This paper introduces a multi-core buckling restrained brace. The multi-core term arises from the use of more than one core component with different steel materials, including high-performance steel (HPS-70W) and stainless steel (304L) with high strain hardening properties. Nonlinear dynamic time history analyses were conducted on variety of diagonally braced frames with different heights, in order to compare the seismic performance of regular and multi-core buckling restrained braced frames. The results exhibited that the proposed multi-core buckling restrained braces reduce inter-story and especially residual drift demands in BRBFs. In addition, the results of seismic fragility analysis designated that the probability of exceedance of residual drifts in multi-core buckling restrained braced frames is significantly lower in comparison to standard BRBFs.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1541-1559
• /
• 2018

This paper addresses the dynamic loading characteristics of the shock tube onto sandwich steel beams as an efficient and accurate alternative to time consuming and complicated fluid structure interaction using finite element modeling. The corrugated sandwich steel beam consists of top and bottom flat substrates of steel 1018 and corrugated cores of steel 1008. The corrugated core layers are arranged with non-uniform thicknesses thus making sandwich beam graded. This sandwich beam is analogous to a steel beam with web and flanges. Substrates correspond to flanges and cores to web. The stress-strain relations of steel 1018 at high strain rates are measured using the split-Hopkinson pressure. Both carbon steels are assumed to follow bilinear strain hardening and strain rate-dependence. The present finite element modeling procedure with an improved dynamic impulse loading assumption is validated with a set of shock tube experiments, and it provides excellent correlation based on Russell error estimation with the test results. Four corrugated graded steel core arrangements are taken into account for core design parameters in order to maximize mitigation of blast load effects onto the structure. In addition, numerical study of four corrugated steel core placed in a reverse order is done using the validated finite element model. The dynamic behavior of the reversed steel core arrangement is compared with the normal core arrangement for deflections, contact force between support and specimen and plastic energy absorption.

• Steel and Composite Structures
• /
• 제44권1호
• /
• pp.105-117
• /
• 2022

Impact resistance efficiency of the newly designed sandwich beam with a laterally arched core as bio-inspired by the woodpecker is numerically investigated. The principal components of the beam comprise a dual-core system sandwiched by the top and bottom laminated CFRP skins. Different materials, including hot melt adhesive, high-density polyethylene (HDPE), acrylonitrile butadiene styrene (ABS), epoxy resin (EPON862), aluminum (Al6061), and mild carbon steel (AISI1018), are considered for the side-arched core layer of the beam for impact efficiency assessment. The aluminum honeycomb takes the role of the second core. Contact force, stress, damage formation, and impact energy for beams equipped with different materials are examined. A diversity in performance superiority is noticed in each of these indicators for different core materials. Therefore, for overall performance appraisal, the impact resistance efficiency index, which covers several chief impact performance parameters, of each sandwich beam is computed and compared. The impact resistance efficiency index of the structure equipped with the AISI1018 core is found to be the highest, about 3-10 times greater than other specimens, thus demonstrating its efficacy as the optimal material for the bio-inspired dual-core sandwich beam system.

• 대한물리치료과학회지
• /
• 제29권4호
• /
• pp.96-111
• /
• 2022

Background: This study aims to evaluate the effect of core stabilization exercise on the dynamic balance and horizontal rotation of the trunk in young adult men. Through this study, it is expected that various core stabilization exercises will prevent and treat musculoskeletal disease. Design: Randomized Controlled Trial. Methods: The study subjects were recruited from young adult men in their 20s and 30s living in Seoul, and after the randomized controlled trial, it was divided into an experimental group training core stabilization exercise(n=15) and a control group(n=15). The evaluation methods of this study were modified Star Excursion Balance Test(mSEBT), Functional Reach Test(FRT), and Trunk Rotation Test(TRT). The experimental group performed three sets of crunches and deadbug exercises twice a week for eight weeks, and the control group did not perform any exercises similar to core stabilization exercise during the experimental period. Results: The result of the experiment, the experimental group showed significant improvement in mSEBT(p<.05), FRT(p<.05) and TRT(p<.05). Conclusion: In conclusion, core stabilization exercises improved dynamic balance and horizontal rotation of the trunk. As a result of this study, core stabilization exercise can prevent and treat musculoskeletal diseases even in healthy people.

• 한국문헌정보학회지
• /
• 제57권4호
• /
• pp.119-138
• /
• 2023

본 연구의 목적은 데이터 리포지토리가 갖추어야 할 디지털 보존 정책의 필수 구성요소를 파악하여 디지털 보존 정책의 프레임워크를 개발하는 것이다. 이를 위해 본 연구에서는 2023년도에 CoreTrustSeal에서 인증을 받은 데이터 리포지토리들의 디지털 보존 정책을 비교 분석하여 디지털 보존 정책 프레임워크에 필요한 구성요소를 추출하고, 각 구성요소에서 어떠한 내용을 포함하고 있는지를 연구 결과로 제시하였다. 본 연구에서 제시한 디지털 보존 정책 프레임워크는 CoreTrustSeal에서 인증을 받고자 하는 기관들뿐만 아니라 CoreTrustSeal 인증을 신청할 계획이 없는 국내외 기관들에서도 그들의 디지털 보존 정책을 개발할 때 기초자료로 이용할 수 있을 것으로 기대된다.

• 한국염색가공학회지
• /
• 제15권4호
• /
• pp.65-72
• /
• 2003

Poly(ethylene-co-vinylacetate) (EVA) microspheres were prepared by a thermally induced phase separation. Poly(vinyl Alcohol) (EVAL) microsphere with Core-Shell Structure were synthesized by a saponification on sheath of EVA microspheres. The size of EVA core/EVAL shell microsphere was decreased from $4.09\mu{m}\;to\;2.55\mu{m}$ by partial saponification of $NaOH/Na_2SO_4$/methanol(2 : 1 : 1 by weight) at $60^\circ{C}$ for 4h to produce a saponified surface layer of about 60% of original radius. In this process, the surface layer of EVAL microsphere was dissolved partially and morphology of surface was not showed. Add-on of cotton and silk printed with EVA core/EVAL shell microsphere was increased and that of printed PET was decreased. In case of EVA core/EVAL shell microsphere, Hand of cotton and silk printed was flexible and fullness.

• 전기학회논문지
• /
• 제57권1호
• /
• pp.52-57
• /
• 2008

In the transformer that is used for the contactless power transmission system, the primary and secondary sides are separated structurally unlike general transformers. When the contactless transformer is built, it forms relatively bigger air gap than the general transformer. Thus it is difficult to transfer energy from the primary side input to the secondary side output with high power efficiently because of low coupling coefficient. This paper proposes a contactless transformer using the rectangular type core that maintains high coupling coefficient even when it has relatively large air gap. The performance characteristics of the proposed transformer are compared with the transformer using general EE core to the air gap variation. The proposed contactless system using rectangular type core and dc-dc full bridge converter, and the system using EE core type and dc-dc full bridge converter are respectively implemented and their performance characteristics are verified by the simulation and experiment.

• 한국주조공학회지
• /
• 제28권4호
• /
• pp.166-169
• /
• 2008

This study deals about the development of fusible core with low melting temperature by addition of ceramic particles. A new concept of salt core was introduced to produce an integrated casting part having a complicated inner shape or requiring under-cut in high pressure die casting or squeeze casting process. The mechanical properties of fusible core were improved due to the addition of ceramic particles which helped to produce fine microstructure. The new technology for the preparation of new fusible core materials which possess high compression strength was established. Addition of ceramics particles increased the mechanical properties of fusible core materials. There was an increasing relationship between percentage of ceramic particles and mechanical strength was existed up to 60%.