• Journal of the Korean Ceramic Society
• /
• v.35 no.1
• /
• pp.41-47
• /
• 1998

Cutting and planarization of diamond films have been performed using copper vapor laser under air at-mosphere. Diamond films of about 350${\mu}{\textrm}{m}$ and 800 ${\mu}{\textrm}{m}$ thick have been synthesized with DC plasma assisted chemical vapor deposition. The position of a specimen has been controlled by computer-driven stage. With copper vapor laser beam of 7W cutting depth increases rapidly and saturates with increasing scan number and decreasing scan speed. 8 repetitive scans at scan speed 0.5 mm/sec produce the maximum cutting depth without focus shifting Rod-shape copper vapor laser beam can be made and used effectively in planar-ization of rough diamond surface.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.9
• /
• pp.1764-1768
• /
• 2009

As the demand of electric power is increasing rapidly, the need of the compact and light electric power device is also increased. Copper clad aluminum (CCA) is newly proposed electrical conductor, because of its light-weight and low-cost characteristics, to replace the existing conductor made of copper. This paper presents the salt-proof characteristics of the copper clad aluminum (CCA) to certificate long time safe operation of the newly proposed electrical conductor. The two types of the CCA conductor were tested in the neutral salt spray tester. The experimental results of two types of the CCA with salt spray were presented in this paper. The results comprise resistance measured data, micro picture of the selected surface, and component measured data according to the elapsed time. The period of the experiment was 1,000 hours. There was no evidence to show the corrosion of CCA during the whole period of the experiments.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.56 no.1
• /
• pp.37-44
• /
• 2007

This paper describes characteristics for copper oxide growth of polyvinyl chloride(PVC) insulated wires by series arc. In this experiment, 600V IV wires were used, and characteristics of oxide growth and ignition process were analyzed in case load was 300W, 460W and 600W, respectively. In the result of experiment, covering materials were molten, carbonized and ignited, whereas, oxidized materials were grown in conducting material. During copper oxide was growing, contact voltages and power dissipations increased. When there is copper oxide growth, the waveform of current showed sinusoidal waveform, and the waveform of voltage showed modified waveform. Oxidized materials were heated at about $905^{\circ}C$, surface structure showed irregular shapes, and cross-section showed multiple cracks. And, the results of this experiment were applied to the fire cause analysis of fire evidence collected at the fire scene.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.318-331
• /
• 2000

Electrical and tribological behaviours of a copper-graphite brush in a slipring-brush assembly were investigated to evaluate the characteristics of electric signal transmission between a slipring and a brush. Five brush materials containing different amounts of copper and graphite were studied. The result showed that a copper-graphite brush at a particular graphite content exhibited the most stable frictional and electrical behaviour suggesting an optimum amount of a solid lubricant in a metal-graphite brush system. Microscopic observation and the surface analysis showed good agreements with this phenomena. In addition, the deviation of the friction coefficient and electric signal distortion has a close relationship with a microscopic mechanical vibration and the change of a real contact area.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.2
• /
• pp.205-209
• /
• 2001

Uniformly-doped silicon thin films were fabricated by ion beam sputter deposition. The thin films had four levels of copper dopant concentration ranging between 1 ${\times}$1019 and 1 ${\times}$ 1021 atoms/cm3 . Concentrations of Copper dopants were determined by the isotope dilution inductively coupled plasma mass spectrometry (ICP-MS) to provide certified reference data for the quantitative surface analysis by secondary ion mass spectrometry (SIMS). The copper-doped thin films were dissolved in a mixture of 1 M HF and 3 M HNO3 spiked with appropriate amounts of 65 Cu. For an accurate isotope ratio determination, both the detector dead time and the mass discrimination were appropriately corrected and isobaric interference from SiAr molecular ions was avoided by a careful sample pretreatment. An analyte recovery efficiency was obtained for the Cu spiked samples to evaluate accuracy of the method. Uncertainty of the determined copper concentrations, estimated following the EURACHEM Guide, was less than 4%, and detection limit of this method was 5.58 ${\times}$ 1016 atoms/cm3.

• Journal of Surface Science and Engineering
• /
• v.50 no.3
• /
• pp.192-197
• /
• 2017

A 6-way-cross consisting of a 2.75-inch CF flange was used as a main chamber on a PFEIFFER VACUUM TMP station based on a 67 l / sec turbo molecular pump and a diaphragm pump to produce a magnet array with a volume ratio of 5.5: 1.A 1-inch diameter copper target and graphite target were fabricated using MDX-1.5K from Advanced Energy Industries, Inc as a DC power supply. Ion current density of copper target and graphite target was measured by unbalanced magnetron sputtering. The basic pressure condition was $6.3{\times}10^{-7}mbar$ and the process pressure was Ar 50 sccm at $1.0{\times}10^{-2}mbar$ (7.5 mTorr) in the Ar atmosphere. Therefore, the relative density of copper ions reaching the substrate with the measured ion current density was derived.

• Journal of Power System Engineering
• /
• v.14 no.4
• /
• pp.50-55
• /
• 2010

In order to investigate tribological effects of nano copper particles impregnated(CuN) on surface polytetrafluoroethylene(PTFE) on sealing wear and an experimental study was carried out to determine the wear behavior of copper nano-particles impregnation two kind thickness in super critical $CO_2$ liquid. Experimental results showed that the friction coefficients of CuN PTFE at the low sliding speed(0.44m/s) and the oil temperature ($60^{\circ}C$) were higher than that of virgin PTFE. And a thin nano copper particles impreganated thickness was formed on the surface in the PTFE and the specimen with this treatment has much better friction properties than the original one. Fortunately, at the high load(80 N) and the oil temperature, the friction coefficient of CuN PTFE was lower than that of virgin PTFE. This evidenced the load carrying capacity of CuN PTFE was much better than that of virgin PTFE under the high load condition(80 N) specially. Therefore, it can be concluded that the friction coefficient variation of CuN PTFE is very small but its wear rate decreases greatly with increase in sliding speed.

• Korean Journal of Materials Research
• /
• v.11 no.10
• /
• pp.820-832
• /
• 2001

In order to obtain the basic data on the optimum conditions of electroforming process for fabricating the micro wiring pattern for plate type micro- motor core, characteristics of plating bath and properties of deposits were studied with various copper plating baths which contain sulfate, fluoborate, pyrophosphate and cyanide salt, respectively. Cathodic polarization, throwing power, internal stress, texture and surface morphology of deposits were observed. Throwing power of plating solution is deeply related to the polarization curves and the values are in the range of +20∼20%. The order of values ate as follows- pyrophosphate, cyanide, sulfate and fluoborate bath. Internal stresses of deposits are tensile in all of the copper plating bath. Thickness of the deposits plated at the center of holes has the highest value in the pyrophosphate bath and K factor, ratio of height and width of deposit, is 1.44. It was confirmed that the pyrophosphate bath was the best one for the electroforming of wire pattern.

• Journal of Surface Science and Engineering
• /
• v.42 no.1
• /
• pp.47-52
• /
• 2009

Cu-Ag powder having Core-Shell structure was prepared from by electroless plating method using agents such as $AgNO_3$, $NH_{4}OH$, Hydroquinone. Ag coated copper powders were analyzed using scanning electron microscopy(SEM) and energy dispersive X-ray spectrometer(EDX). The silver coating layer of copper powder was affected from various reaction conditions such as molar ratio of $NH_{4}OH$, $AgNO_3$, and pulp density. Free silver was generated below 0.1M or 0.3M and above of $NH_{4}OH$ mole ratio. Silver coating layer thickened as addition of $AgNO_3$. When the pulp density reached 12% with 0.2M $NH_{4}OH$, and 0.15M $AgNO_3$ at $4^{\circ}C$, silver was homogeneously distributed around the copper particles and free silver particles were not generated.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.97-103
• /
• 2007

A novel selective metallization process to fabricate the fine conductive line based on inkjet printing has been investigated. Recently, Inkjet printing has been widely used in flat panel display, electronic circuits, biochips and bioMEMS because direct inkjet printing is an alternative and cost-effective technology for patterning and fabricating objects directly from design without masks. The photosensitive etching resist used in this process is an organic polymer which becomes solidified when exposed to ultraviolet lights and has high viscosity at ambient temperature. A piezoelectric-driven inkjet printhead is used to dispense 20-30 ${\mu}m$ diameter droplets onto the copper substrate to prevent subsequent etching. Repeatability of circuitry fabrication is closely related to the formation of steady droplets, adhesion between etching resist and copper substrate. Therefore, the ability to form small and stable droplets and surface topography of the copper surface and chemical attack must be taken into consideration for fine and precise patterns. In this study, factors affecting the pattern formation such as adhesion strength, etching mechanism, UV curing have been investigated. As a result, microscale copper patterns with tens of urn high have been fabricated.