• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.9
• /
• pp.26-34
• /
• 1998

This paper presents a characterization method for faults of circuit patterns on MCM(Multichip Module) or PCB(Printed Circuit Board) substrates with electron beams of a SEM(Scanning Electron Microscope) by inducing voltage contrast on the signal line. The experimentation employes dual potential electron beams for the fault characterization of circuit patterns with a commercial SEM without modifying its structure. The testing procedure utilizes only one electron gun for the generation of dual potential electron beams by two different accelerating voltages, one for charging electron beam which introduces the yield of secondary electron $\delta$ < 1 and the other for reading beam which introduces $\delta$ > 1. Reading beam can read open's/short's of a specific net among many test nets, simultaneously discharging during the reading process for the next step, by removing its voltage contrast. The experimental results of testing the copper signal lines on glass-epoxy substrates showed that the state of open's/short's had generated the brightness contrast due to the voltage contrast on the surface of copper conductor line, when the net had charged with charging electron beams of 7KV accelerating voltages and then read with scanning reading electron beams of 2KV accelerating voltages in 10 seconds. The experimental results with Au pads of a IC die and Au plated Cu pads of BGA substrates provided the simple test method of circuit lines with 7KV charging electron beam and 2KV reading beam. Thus the characterization method showed that we can test open and short circuits of the net nondestructively by using dual potential electron beams with one SEM gun.

• Resources Recycling
• /
• v.28 no.6
• /
• pp.96-105
• /
• 2019

Automobile shredder residue (ASR) is the final waste produced when end-of-life vehicles (ELVs) are shredded. ASR can be separated using mineral-processing operations such as comminution, air classification, magnetic separation, and/or electrostatic separation. In this work, trajectory analyses of conductors (copper) and non-conductors (glass) in the ASR have been carried out using induction electrostatic separator for predicting or improving the ASR-separation efficiency. From results of trajectory analysis for conductors, the trajectories of copper wire by observation versus simulation for coarse particles of 0.5 and 0.25 mm showed consistent congruity. The observed 0.06 mm fine-particles trajectory was deflected toward the (-) attractive electrode owing to the charge-density effects due to the particle characteristics and relative humidity. In the case of non-conductors, the actual trajectory of dielectric glass deflected toward the (-) electrode, showing characteristics similar to those of conductive particles. The analyses of stereoscopic microscope and SEM & EDS found heterologous materials (fine ferrous particles and conductive organics) on the glass surface. This demonstrates the glass decreasing separation efficiency for non-ferrous metals during electrostatic separation for the recycling of ASR. Future work will require a pretreatment process for eliminating impurities from the glass and advanced trajectory-simulation processes.

• Economic and Environmental Geology
• /
• v.31 no.6
• /
• pp.463-472
• /
• 1998

The survey was carried out in order to delineate the occurrence of ore deposits and the mineralized characteristics in the Estancia de la Virgen area through the 1:2,000 scaled geological mapping and topographic measuring surveys. Gold-silver mineralization is in the fault block developed between the San Agustin Fault and Cabanas Fault. It is associated with ore bearing quartz veins controlled by the fault structure. The contents of Au and Ag range from traces up to 72 g/t and 180 g/t respectively. According to traversing the outcrops, the quartz veins are traced by 0.5 Km trended to north and south. In those extended part, they continue for 1,000 m intermittently. Gold-silver mineralization could be divided into three stages. In the first stage, pyrite, galena, sphalerite, and chalcopyrite were formed with the primary silver and gold associated with galena and copper sulfides respectively. In the second stage, Cu-Bi-Au-Ag bearing sulfides such as chalcocite, covellite, and linarite are formed and usually deposited on the cataclastic fractures of galena and/or chalcopyrite. In the third stage, both the carbonation of galena and sphalerite and the sulphatization of galena, took place in the surface environment. And then primary silver was carried away off and was deposited on galena and/or copper sulfides during oxidation near the water table. Low partitionings of Fe in sphalerite assist that the minerals were formed at the relatively low temperature, which is coincided with previously reported homogenization temperature of fluid inclusions.

• Korean Journal of Environmental Agriculture
• /
• v.16 no.2
• /
• pp.142-148
• /
• 1997

This study was performed to develop the biological treatment technology of wastewater polluted with heavy metals. Heavy metal-tolerant microorganisms, such as Pseudomonas putida, P. aeruginosa, P. chlororaphis and P. stutzeri possessing the ability to accumulate cadmium, lead, zinc and copper, respectively, were isolated from industrial wastewaters and mine wastewaters polluted with various heavy metals. The effect of competing ions and metabolic inhibitors on heavy metal accumulation in the cells was investigated. Heavy metal accumulation into cells was drastically decreased in the presence of competing cation, $Al^{3+}$, and also decreased, at a lesser extent, in the presence of competing anions, $CO_3\;^{2-}$ and $PO_4\;^{2-}$. But heavy metal accumulation was not influenced generally in the presence of the other rations and anions. The accumulation of Cd, Zn or Cu by Cd-, Zn- or Cu-tolerant microorganism was remarkably decreased in the presence of metabolic inhibitors, but the accumulation of Pb by Pb-tolerant microorganism was little affected in the presence of metabolic inhibitors. These results suggested that the accumulation of Cd, Zn or Cu by Cd-, Zn- or Cu-tolerant microorganism was concerned with the biological activity depending on energy, and the accumulation of Pb by Pb-tolerant microorganism depended on not the biological activity but the physical adsorption on the cell surface. Each heavy metal-tolerant microorganism also exhibited some ability to accumulate the other heavy metals in solution containing equal concentrations of cadmium, lead, zinc and copper, when measured at 48 hours after inoculation of the microorganisms, but the accumulation rates were somewhat low as compared to the accumulation rates of heavy metal fitting to each tolerance. These results suggested that the accumulation of each heavy metal by each heavy metal-tolerant microorganism was a selective accumulation process.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.8
• /
• pp.930-937
• /
• 2007

Korean pine(Pinus densiflora) bark was evaluated for its adsorption capacity of Cu(II) ions from aqueous solution by running a series of batch experiments. Prior to the tests, the milled barks were treated with 1 N NaOH or 1 N HCl to examine the effect of surface modification. For comparison, untreated bark was tested under same condition. Within the tested pH range between 3 and 6, NaOH treatment increased Cu(II) adsorption capacity by $139\sim184%$, while HCl treatment decreased it by $37\sim42%$. Maximum copper ion uptake by bark was observed at pH $5\sim6$, but pH of solution was not a potent influence. A pseudo second-order kinetic model fitted well for the sorption of copper ion onto bark. For NaOH-treated bark, the calculated sorption capacity$(q_e)$ increased from 6.58 to 12.77 mg/g, while the equilibrium rate constant$(k_2)$ decreased from 0.284 to 0.014 g/mg/min as initial Cu(II) concentration doubled from 100 mg/L. A batch isotherm test using NaOH-treated bark showed that equilibrium sorption data were represented by both the Langmuir model and the Freundlich model. It was confirmed that carboxylic acid of bark was involved in the Cu(II) adsorption. For NaOH-treated bark, in particular, carboxylate ion produced by hydrolysis or saponification appeared to be a major functional roup responsible for the enhanced Cu(II) sorption.

• Korean Journal of Soil Science and Fertilizer
• /
• v.31 no.3
• /
• pp.225-232
• /
• 1998

In order to monitor the degree of heavy metal distribution in upland cultivations in Korea, both the cultivated soils and crops were collected from the 854 and 140 sites, respectively. The contents of cadmium (Cd), copper(Cu), lead(Pb), and zinc(Zn) in each sample were measured by Inductively Coupled Plasma(ICP) technique after 1N-HCl extraction. The content of Arsenic(As) was also measured with the same technique after 1N-HCl extraction. The average contents of heavy metal in surface soils(0~15 cm depth) were $0.135mg\;kg^{-1}$ for Cd, $2.77mg\;kg^{-1}$ for Cu, $3.47mg\;kg^{-1}$ for Pb, $10.7mg\;kg^{-1}$ for Zn, and $0.57mg\;kg^{-1}$ for As. Heavy metal contents of soil were similar to those values measured for upland soils in 1989, lower than soils under plastic film house in 1996. However, these contents were lower than "Countermeasure values for soil contamination"(Cd: 4, Cu: 125, Pb: 300, and As: $15mg\;kg^{-1}$ in soil) describled in Soil Environmental Conservation Act in Korea(1996). The contents of heavy metal in fresh vegetable, and root and tuber crops ranged $0.005{\sim}0.019mg\;kg^{-1}$ for Cd, $0.20{\sim}1.03mg\;kg^{-1}$ for Cu, $0.042{\sim}0.104mg\;kg^{-1}$ for Pb, and $2.0{\sim}4.0mg\;kg^{-1}$ for Zn, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.155-161
• /
• 2013

In this study, a metal-plated polycarbonate was adopted as a material for bipolar plates in a polymer electrolyte membrane fuel cell (PEMFC). The coated layers included 40-${\mu}m$-thick copper, 10-${\mu}m$-thick nickel, and 0.3-${\mu}m$-thick gold that respectively played the roles of current conduction, adhesion between copper and gold, and minimization of surface corrosion. The maximum power of the air-breathing PEMFC with polycarbonate bipolar plates was $120mW/cm^2$, which was similar to that of graphite bipolar plates. Finally, the maximum power of a 12-cell stack of polycarbonate bipolar plates was $132.7mW/cm^2$, and it had an operating time of 12 h. Therefore, this was considered a suitable material for bipolar plates in PEMFCs.

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.404-409
• /
• 2006

The catalytic combustion of toluene over Pd-Cu/USY zeolite has been examined by using FT-IR spectroscopy in a closed system under dry and humid conditions. The catalytic combustion of toluene (700 ppmv) in the temperature range of $80-220^{\circ}C$ has been investigated by using a fixed bed reactor. The Pd-Cu/USY catalyst showed the highest catalytic performance with respects to the PdO-CuO/USY and Pd/USY. Comparing to $PdO/Al_2O_3$ catalysts, the slight improvement in conversion was observed over PdO/USY catalysts under humid condition since USY zeolite is hydrophobic substrate and water give an additional oxygen source to zeolite surface like oxygen. The reduced catalysts showed more enhanced catalytic activity due to the reduced activation energy of combustion of toluene than oxidized catalysts such as PdO/USY and PdO-CuO/USY.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.3
• /
• pp.345-351
• /
• 2008

Fe-impregnated activated carbon(Fe-AC) was prepared by Fe(III) loading on activated carbon(AC) in various preparation pH. In order to evaluate the stability of Fe-AC, dissolution of iron from Fe-AC in acidic conditions was measured. In addition, batch experiments were conducted to monitor the removal efficiency of copper by Fe-AC. Results of stability test for Fe-AC showed that the amount of extracted iron increased with contact time but decreased with increasing solution pH. The dissolved amount of iron gradually increased at solution pH 2 and finally 13% of the total iron loaded on activated carbon was extracted after 12 hr. However dissolution of iron was negligible over solution pH 3. Removal of Cu(II) by Fe-AC was greatly affected by solution pH and was decreased as solution pH increased as well as initial Cu(II) concentration decreased. Surface complexation modeling was performed by considering inner-sphere complexation reaction and using the diffuse layer model with MINTEQA2 program.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.313-319
• /
• 2012

In this work, the electroplating of copper was introduced on PAN-based carbon fibers for the enhancement of mechanical interfacial strength of carbon fibers-reinforced composites. The surface properties of carbon fibers were determined by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and contact angle measurements. Its mechanical interfacial properties of the composites were studied by interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$). From the results, it was found that the mechanical interfacial properties of Cu-plated carbon fibers-reinforced composites (Cu-CFRPs) enhanced with increasing the Cu plating time, Cu content and COOH group up to Cu-CFRP-30. However, the mechanical interfacial properties of the Cu-CFRPs decreased dramatically in the excessively Cu-plated CFRPs sample. In conclusion, the presence of Cu particles on carbon fiber surfaces can be a key factor to determine the mechanical interfacial properties of the Cu-CFRPs, but the excessive Cu content can lead the failure due to the interfacial separation between fibers and matrices in this system.