• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.4
• /
• pp.361-365
• /
• 2003

A unipolar-type E-chuck was fabricated for the application of holding silicon wafers in the oxide etcher. For the fabrication of the unipolar ESC, core technologies such as coating of polyimide films and anodizing treatment of aluminum surface were developed. The polyimide films were prepared on thin coated copper substrates to minimize the plasma damage during the etch processing. Thin film heater technology was also developed for new type of E-chuck.

• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.34-42
• /
• 2000

A method and results of classification of four different metallic wear debris were presented by using their color features. The color image of wear debris was used far the initial data, and the color properties of the debris were specified by HSI color model. Particles were characterized by a set of statistical features derived from the distribution of HSI color model components. The initial feature set was optimized by a principal component analysis, and multidimensional scaling procedure was used fer the definition of a classification plane. It was found that five features, which include mean values of H and S, median S, skewness of distribution of S and I, allow to distinguish copper based alloys, red and dark iron oxides and steel particles. In this work, a method of probabilistic decision-making of class label assignment was proposed, which was based on the analysis of debris-coordinates distribution in the classification plane. The obtained results demonstrated a good availability for the automated wear particle analysis.

• Journal of Powder Materials
• /
• v.1 no.2
• /
• pp.167-173
• /
• 1994

Cu-10wt%W composite powders have been manufactured by a high energy ball milling technique. The composite powders were pressed at 250 MPa and sintered in a dry hydrogen at 103$0^{\circ}C$ for 4 hours. After sintering, Cu-10wt%W composite materials were forged. And the arc-resistance of forged materials which have the same relative density of 94% has been tested. Composite particles, i.e. tungsten particles distributed homogeneously in the copper matrix, was formed after 480 min mechanical alloying. Densities of these sintered materials were ranged from 74 to 84%. Densification degree was due to the formation of composite powders. As the mechanical alloying time increased, the hardness was increased and tungsten particle size was decreased. Arc loss of the forged specimens was decreased as increasing the mechanical alloying time.

• Journal of Welding and Joining
• /
• v.20 no.5
• /
• pp.106-112
• /
• 2002

In the present study, the wettability and interfacial tension between (bare Cu, electroless Ni/cu, immersion Au/Ni/Cu) substrates and indium solder were investigated as a function of soldering temperature, types of flux. The wettability of In solder increased with soldering temperature and solid content of flux. The wettability of In solder was affected by the substrate metal finish used, i.e., nickel, gold and copper. On the bare Cu substrate, In solder wet better than any of the substrate metal finishes tested. Intermetallic compound formation between liquid solder and substrate reduced the interfacial energy and improved wettability. For the identification of intermetallic compounds, X-Ray Diffraction(LRD) were employed. Experimental results showed that the intermetallic compounds, such as Cu11In9 and In27Ni10 are observed f3r different substrates respectively. The wetting kinetics is investigated by measuring wetting time with the wetting balance technique. The activation energy of wetting calculated for the In solder/cu substrate and In solder/electroless Au/Ni/Cu substrate are 36.13 and 27.36 kJ/mol, respectively.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.207-210
• /
• 1997

The Linear D.C Motor with moving magnet type structured two permanent magnets, three iron bars and winding copper around one of bars. This paper describes the design theory and trust characteristic analysis of Linear D.C Motor. The design theory is very important to Motor design. Here, The design method be obtained by the design theory equation based the flux distribution and design constant. The propriety for this is established by the experiment results.

• Journal of Environmental Science International
• /
• v.12 no.10
• /
• pp.1061-1069
• /
• 2003

The adsorption behaviors of strontium and cesium ions on fly ash, natural zeolites, and zeolites synthesized from fly ash were investigated. The zeolites synthesized from fly ash had greater adsorption capabilities for strontium and cesium ions than the original fly ash and natural zeolites. The maximum adsorption capacity of synthetic zeolite for strontium and cesium ions was 100 and 154 mg/g, respectively, It was found that the Freundlich isotherm model could fit the adsorption isotherm. The distribution coefficients (K$\_$d/) for strontium and cesium ions were also calculated from the adsorption isotherm data, The distribution coefficients decreased with increasing equilibrium concentration of strontium and cesium ions in solution. By studying the removal of cesium and strontium ions in the presence of calcium, magnesium, sodium, potassium, sulfate, nitrate, nitrite, and EDTA (in the range of 0.01 - 5 mM) it was found that these coexistence ions competed for the same adsorption sites with strontium and cesium ions.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.1
• /
• pp.24-33
• /
• 1997

In this paper, aging of insulating oil in pole transformer has been studied by performing accelerated thermal aging test. Dissolved gases were extracted by air bubbling method. Concentration of dissolved gases were modified by extraction ratio of each gases in insulting oil. Aging of insulting materials were proceeded by thermal degradation and oxidation reaction. Both of the reactions followed zeroth order kinetics. Formation rate equations for hydrocarbons, carbon oxides, and hydrogen were derived. It was conformed by gas analysis and UV-visible spectrophotometric method that iron core and copper coil in pole transformer act as catalyst during the aging process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.123-123
• /
• 2008

본 논문에서는 Cu의 ECMP 적용을 위해 $HNO_3$ 전해액의 active, passive, transient, trans-passive 영역을 I-V 특성 곡선을 통해 알아보았고, LSV (Linear sweep voltammetry)와 CV (Cyclic voltammetry)법을 통하여 전기화학적 특성을 비교 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.506-507
• /
• 2008

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different metal electrode. The CuPc FET made a top-contact type and the substrate temperature was room temperature. The source and drain electrodes were used an Au and Al materials. The CuPc thickness was 40nm, and the channel length was $50{\mu}m$, channel device was width was 3mm. We observed a typical current-voltage (I-V) characteristics in CuPc FET with different electrode materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04b
• /
• pp.12-13
• /
• 2008

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different metal electrode. The CuPc FET device was made a top-contact type and the substrate temperature was room temperature. The source and drain electrodes were used an Au and Al materials. The CuPc thickness was 40nm, and the channel length was $50{\mu}m$, channel width was 3mm. We observed a typical current-voltage (I-V) characteristics in CuPc FET with different electrode materials.