• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.3 no.1
• /
• pp.51-60
• /
• 1991

The aim of this study is to investigate the heat transfer characteristics in the transient cooling process of a high temperature wall. The slow transient cooling experiment was carried out with a copper block of high thermal capacity. The results of these experiments are as follows. 1. Temperature histories measured by the thermocouple, which is 0.99, 2.00, 2.99mm from the heat transfer surface showed monotonous during the cooling process. These variation are the curves of typical temperature histories in film-boiling, transition-boiling, and nucleate-boiling regions. 2. The temperature histories were measured by thermocouple installed in the copper block. The variations of the surface heat fluxes and surface temperature were computed from the numerical solution method TDMA from the measured temperature histories for radial position one dimensional heat transfer inverse problem. The boiling curves were found by the computed temperature histories. 3. The rewetting point which starts to change from film boiling to nucleate boiling is not connected with the mass velocity and it were found that the temperature of rewetting point indicated about $100^{\circ}C$. 4. The heat flux of rewetting point was about $10^5Kcal/m^2h$, at that time, the heat transfer coeficient indicated about $1000Kcal/m^2h^{\circ}C$ irrelevent to mass velocity. 5. The wall superheat decreases as the pressure increases. But I found that rewetting point appeared under higher condition in the wall temperature.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.4
• /
• pp.377-389
• /
• 2020

In this study, pollution characteristics were investigated for the Andong Dam sediments in the Nakdong River. Sediment samples were collected from the middle, left, and right points of the lake up to 40km upstream of the Andong Dam at intervals of about 5km by stratification and turnover period. In the case of nutrients and total organics such as loss of ignition, total nitrogen, and phosphorus, the degree of contamination is low, but heavy metals of arsenic and cadmium is very high. The contamination level of sediments in the dam area is higher than that of the branch of river and the control group, and concentration of chromium, copper, and lead are higher in the stratification period, and that of zinc is higher in turnover period. Arsenic, cadmium, manganese, and zinc showed contamination variation between upstream and downstream but chromium, copper, mercury, iron and lead didn't show the variation.

• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.345-353
• /
• 1998

Metal organic chemical vapor deposition (MOCVD) of copper using three Cu( I ) precursors. (hfac)Cu (VTMS) (hfac= hexafluoroacetylacetonate, VTMS= vinyltrimethylsilane), (hfac)Cu(VTMOS) (VTMOS= vinyltri¬methoxysilane) and (hfac)Cu(A TMS) (A TMS= allyltrimethylsilane) was studied. The thermal stability and the gase¬ous phase reaction mechanism of Cu( I ) precursors were identified using $^1H$-, $^I3C$-NMR and Fourier transform infra¬red spectroscopy. It was found out that thermal stability of liquid phase (hfac)Cu(VTMS) and (hfac)Cu(VTMOS) were better than that of (hfac)Cu(A TMS) using FT - NMR. From in-situ FT - IR experiments, the disproportion reaction of Cu(hfac). the decomposition reaction of Cu(hfac), and cracking of free hfac ligand were observed. Also the effect of gaseous phase reaction on the deposition rates and film properties was investigated. The minimum temperature that deposition of copper films from (hfac)Cu(A TMS) was as low as 60$^{\circ}$C and such a low deposition temperature compared with those of other Cu( I ) precursors is believed to be related with weaken Cu- A TMS bond.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1187-1189
• /
• 1995

The paper is concerned with the pre-arcing behavior of rapid current limiting fuselink using copper as a melting element. The phenomenon is faced by a numerical simulation(especially, FDM is applicated) of the melting element. Through the results, we can know the trends of the I-t characteristics and temperature distribution along the x axis for different fuselink shapes with circular, rectangular, and skew restriction type respectively, to be good for designing the optimal element.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.1-5
• /
• 2004

This paper presents a study on the stability of bare and cu-laminated YBCO-coated conductor. we investigate the characteristics of quench/recovery behavior of YBCO test samples. bare and copper-laminated, by subjecting each test sample. immersed in a bath of liquid nitrogen boiling at 77.3 K. to a transport current pulse superimposed to a baseline DC current of 90-95% the critical current. The current pulse has an amplitude up to ∼4.5 times the critical current and a duration of 300 ms. This paper presents both experimental and simulation results.

• The Korean Journal of Mycology
• /
• v.16 no.4
• /
• pp.242-246
• /
• 1988

To determine contents of inorganic elements of Laccaria, the carpophores of Laccaria laccata(Fr.) Berk. et Br., Laccaria amethystina(Fr.) Berk. et Br., Laccaria tortilis(S.P. Gray) Cooke and Laccaria vinaceoavellanea Hongo were incinerated and analyzed by atomic absorption spectrophotometer. Total contents of determined inorganic elements(except Cd) were highst in Laccaria tortilis than the other three mushrooms, and Laccaria vinaceoavellanea, Laccaria laccata and Laccaria amethystina in that order. The four species mushrooms contained potassium, iron, zinc, sodium, copper, manganese, and calsium in that order, and the content of potassium was the highst than the other inorganic components. The content of cadmium was Laccaria tortilis, Laccaria laccata, Laccaria vinaceoavellanea and Laccaria amethystina in that order.

• Proceedings of the KAIS Fall Conference
• /
• 2007.05a
• /
• pp.291-293
• /
• 2007

인산염을 이용한 구리 고정화 실험의 토양적용가능성을 평가하고자 액상반응실험과 고정화물의 재용출 실험을 수행하였다. 액상반응실험 결과 인산염과 알칼리제 1mole을 넣은 반응에서 99.9% 의 구리제거효율을 보였고 구리의 재용출 농도는 0.64mg/L로 초기농도인 1000mg/L보다 현저히 낮은 값을 나타내었다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.7 no.4
• /
• pp.229-233
• /
• 1974

The author studied On the inorganic substances in the muscles of Branchiostegus joponicus japonicus, Chromis notatus, Haliotis gigantea mataka, obtaining the following results ; 1) The results of quantitative analysis are shown in Table 3. 2) It is noticeable that the concentration of Cu, P, Fe, Ca, and Na in the muscles of Branchiostegus joponicus japonicus (demersal fish), Chromis notatus (pelagic fish) and Haliotis gigantea mataka (shell fish) are quite different in the three species.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.5
• /
• pp.851-859
• /
• 1997

This study was perfomed to investigate the contamination level of harmful heavy metals and the level of trace elements in 15 kinds of fish collected at the western coast in Korea from July to December in 1996. The levels of total lead, cadmium, mercury, iron, copper and zinc were determined and the results were summarized as follows: The minimum and maximum values(ppm) of fish, mean value bracketed, were ; Pb : 0.02~4.80(2.26), Cd: 0.001~0.54(0.04), Hg: 0.007~1.08(0.52), Fe: 7.76~66.39(25.70), Cu; 0.37~121.6(1.90), Zn:12.01~112.10(54.78). The results show that mean contents of Pb, Cd and Hg in 15 species fish were not yet dangerous levels enough to cause a health problem. But the contents of Pb and Hg tend to increase.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.52-59
• /
• 1996

Conventionally, grinding of stainless steel, aluminium ally, copper alloy, and titanum alloy are difficult to obtain the high quality finish, because they have the mechanical properties such as low hardness, high toughness which result in the loading of wheel and the poor surface finish. Inorder to perform the grinding operations for these sorts of materials easily, the discontinuous grinding wheel with multi-porous grooves has newly been developed. The multi-porous grooves were formed during wheel production. This discontinous grinding wheel increases the grinding performance. It is desirable to use the discontinuous grinding wheel when grinding materials wiht high efficiency and accuracy which is impossible by conventional wheels. In this paper, the constructing and manufacturing method of grinding wheel with multi-proous grooves are explained, and the grinding charateristics of discontinuous grinding wheel are also illustrate.