• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제18권8호
• /
• pp.720-723
• /
• 2005

We studied the quantitativity of the image sticking which is occured by the resicual DC in the fringe-electric field switching (FFS) mode. Actually, in the FFS mode driven by the strong fringe electric field, the asymmetric residual DC was formed in the bottom substrate. It made the impurity ion stick to the alignment layer such as polyimde layer. Thus, the differnece of the luminance existes after the stress check pattern is applied to the panel so that we can see the image sticking. This image sticking decreases as the residual DC value between specific patterns decreases. Therefore, it is necessary to control the residual DC for the FFS mode with the high image quality. It is possible to eliminate the image stiking when the extra pixel voltage is applied through the circuit tunning for reducing the difference of residual DC accroding to the panel position.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.2138.1_2139.1
• /
• 2009

COS 조작봉은 선로의 사고나 설비교체 또는 수리 등이 필요할 때 활선상태에서 COS를 개폐하기 위한 장비로서 보통 절연특성 및 강도가 우수하고 경량소재인 FRP(Fiberglass Reinforced Plastics)로 제작된다. 따라서 특고압 선로에서 작업 중 안전사고를 예방하기 위해 사용되는 장비인 만큼 안전거리 확보와 작업의 편리성을 고려하여 직접 조작봉을 연장하여 사용할 수 있도록 다단으로 제작되며, 조작봉의 크기는 작업조건에 따라 길이를 선택하여 사용할 수 있도록 2, 4, 6m급 등 길이에 따른 종류별로 생산되고 있다. 이러한 COS 조작봉의 사용특징은 장소와 시간에 관계없이 사용이 가능해야 하고, 특정한 사정에 의해선 작업자 혼자서 사용할 수 있도록 조작봉과 일체된 조명장치의 필요성이 항상 제기되어 왔던 문제이다. 본 논문에서는 이러한 문제점에 주안을 두고 조작봉과 일체된 전계검출에 의한 발광동작을 제어할 수 있는 발광형 COS 조작봉에 대해 각각의 구성별 요소들을 분석하고자 한다.

• Journal of the Korean Society for Marine Environment & Energy
• /
• 제1권2호
• /
• pp.18-26
• /
• 1998

The major interest of this paper is how the spilled oil over the sea is dispersed into water column especially under the shear and turbulence such as breaking wave. Two hydraulic experiments were conducted to investigate the oil stick break-up characteristics into small and large droplets under the variation of velocity shear and breaking waves. From the experiments in the shear generator and the wave flume, small droplets which have diameters of tens to hundreds of micrometers were uniformly distributed throughout the whole control volume as time goes by. In addition, it can be seen that the weathered spilled oil has a different break-up mechanism from fresh spilled oil.

• Journal of Korea Multimedia Society
• /
• 제13권7호
• /
• pp.1105-1114
• /
• 2010

This thesis is a summary of the research result about the 20 seconds official trailer requested from the Pusan International Film Festival organizing committee. Since producing digital content is very significant at this moment, I tired to make an official trailer for 13th Pusan International Film Festival by integrating 3D animation with ink-and-wash painting. Motivated by a western-style painter, Shin Chang Sic's painting,' Arirang_HopeⅠ(An Official poster), I got to know how to express ink-and-wash painting by using digital technique and considering ink stick depth, line control and color elements for modeling, shading and rendering stage.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• 제31권2호
• /
• pp.15-24
• /
• 1999

A new technique for recycling of white water was developed in order to reduce the calcium hardness in a closed OCC recycling system. Calcium ions present in the white water were precipitated as calcium carbonate by reacting with sodium carbonate, and the precipitated $CaCO_3$ was removed from the system using a flotation fractionation method, which has been commonly used in deinking process. In the flotation stage, a mixed gas of $CO_2$-air was purged into the flotation cell because the pH of $Na_2CO_3$-treated white water was reduced to neutral by $CO_2$ gas. Since $CaCO_3$ precipitate tends to stick onto fine fiber surface and then selectively removed from the white water, a proper amount of suspended solid in white water acts as an important factor for deciding the removal efficiency. By the application of $Na_2CO_3$ addition-$CO_2$ flotation to the short circulated white water, the calcium hardness was significantly reduced by 87% and more. Removal of calcium ions with fine fibers led to a drainage improvement, reduction of fresh water consumption, and enhanced efficiency of wet-end chemicals.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 한국펄프종이공학회 1999년도 Proceedings of Pre-symposium of the 10th ISWPC
• /
• pp.164-171
• /
• 1999

A new technique for recycling process water was developed in order to reduce the calcium hardness of the closed OCC recycling system. Calcium ions present in the white water were precipitated as calcium carbonate by a reaction with sodium carbonate and the CaCO$_3$precipitates were easily removed from the system by a dissolved air flotation(DAF) method. After the DAF stage, CO$_2$-gas was purged into the water because the pH of Na$_2$CO$_3$-treated white water was reduced to neutral by CO$_2$gas. Since CaCO$_3$precipitate tends to stick onto the fine fiber surface and then is selectively removed from the water, a proper amount of suspended solid in the process water acts as an important factor in deciding the removal efficiency. By the application of Na$_2$CO$_3$addition - DAF - CO$_2$purging to the short circulated white water the calcium hardness was significantly reduced by 92% and more. The removal of calcium ions with fine fibers led to drainage improvement, reduction of fresh water consumption, and enhanced efficiency of wet-end chemicals.

• Journal of KIBIM
• /
• 제1권1호
• /
• pp.1-5
• /
• 2011

Earthwork is important in terms of construction time and duration, and highly related to the construction productivity. However, current earthwork system has stick to labor intensive process depending on skilled operator's heuristic decision making, so it is hard to improve overall productivity. To overcome this drawback, this paper presents a BIM based Intelligent Excavation System(IES). The BIM technology is applied in the excavation task planning system, Human-Machine Interface for remote-control/autonomous work environment, and web-based Project Management Information System(PMIS) in the IES integration process, and the results are addressed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권2호
• /
• pp.226-232
• /
• 2002

In tradition, there have been two kinds of drying methods, which are sun drying and artificial drying. The sun drying method which has been adopted traditionally has been replaced by the hot-air drying method which is one of the most general methods of artificial drying, with its simple drying system, low initial cost of drying plant, and easy operating method. But the hot-air drying method has some defects ; (1)much energy loss happens due to the discharge of hot air during the drying process, (2)control of drying rate is not easy on account of changing relative humidity of inlet air for uniform hot air temperature, (3)high temperature of floods in drying process brings about the production of low-grade drying products. Also, the hot-air drying method is inducing environmental and sanitary problems which are resulting from the emission of high temperature and high humidity air, including stick on the drying progress. Vacuum drying technique, whose drying time and 7uantity of exhausting energy is about 1/3 ~1/4 of hot air drying, is very excellent in the drying efficiency. As the results, it took about 20 hours for material to reach about 18% of the final moisture content in order to store products for a long time, from about 470% of the early moisture content at the beginning of drying, and maximum drying rate comes to about $0.35 kg/m^2hr$ at about 350% of the moisture content.

• Plant Journal
• /
• 제13권3호
• /
• pp.30-35
• /
• 2017

Module can be categorized as PAS(Pre-Assembled Steel structure), PAR(Pre-Assembled pipe Rack), PAU(Pre-Assembled Unit), VAU(Vendor Assembled Unit) and VPU(Vendor Package Unit). At the stage of design and fabrication of module, the condition of land and ocean transportation is considered and these conditions are reflected on the module division design. The control of the module's center of gravity is important to transport and install modules safely and the steel structure should have the strength enough to resist the sea acceleration force during the ocean transportation. The transportation condition and the installation method influence the size and weight of module. The size and weight of module are considered for the design of module division.

• Physical Therapy Korea
• /
• 제18권4호
• /
• pp.51-59
• /
• 2011

The purpose of this study was to investigate the effect of attentional focus and distance of external focus on the performance of balance task of upper extremity. Subjects (N=30) held a stick (2 m) and maintained it horizontally. All of the subjects performed balance task of upper extremity under four different attentional focus conditions: focus on hand (internal focus), marker at 10 cm inside of hand (external focus 1), marker at 10 cm outside of hand (external focus 2), marker at 20 cm outside of hand (external focus 3). The mean velocity of the bar (mm/s) and the muscle activity of biceps brachii (%RVC) were measured. They were decreased when the subjects focused on external focuses compared to internal focus and decreased as distance of attentional focus from body increased (p<.05). There were significant differences between groups (p<.05); internal focus-external focus 1, internal focus-external focus 2, internal focus-external focus 3, external focus 2-external focus 3. These results showed that external focus is more effective than internal focus in enhancing motor performance and focusing on more distant attentional focus results in enhanced motor performance promoting the utilization of more automatic control mechanisms.