• Transactions on Electrical and Electronic Materials
• /
• v.4 no.3
• /
• pp.10-14
• /
• 2003

In this paper, we have introduced the x-ray detector built with a CsI:Na scintillation layer deposited on amorphous selenium. To determine the thickness of the CsI:Na layer, we have estimated the transmission spectra and the absorption of continuous x-rays in diagnostic range by using computer simulation (MCNP 4C). A x-ray detector with 65 ${\mu}m$-CsI:Na/30 ${\mu}m$-Se layer has been fabricated by a thermal evaporation technique. SEM and PL measurements have been performed. The dark current and x-ray sensitivity of the fabricated detector has been compared with that of the conventional a-Se detector with 100 ${\mu}m$ thickness. Experimental results show that both detectors exhibit a similar dark current, which was of a low value below $400 pA/cm^2$ at 10 V/${\mu}m$. However, the CsI:Na-Se detector indicates high x-ray sensitivity, roughly 1.3 times that of a conventional a-Se detector. Furthermore, a CsI:Na-Se detector with an aluminium reflective layer shows a 1.8 times higher x-ray sensitivity than an a-Se detector. The hybrid type detector proposed in this work exhibits a low dark current and high x-ray sensitivity, and, in particular, excellent linearity to the x-ray exposure dose.

• Journal of the Korean Society of Physical Medicine
• /
• v.15 no.2
• /
• pp.101-108
• /
• 2020

PURPOSE: The purpose of this study was to investigate the effect of treadmill walking training using the metronome on the gait pattern. METHODS: A total of 33 healthy persons were studied consisting of 17 female and 16 male in the 20-30 age group. A gait analysis program was installed on a treadmill with a built - in gait analysis sensor and laptop. After 9 minutes of treadmill walking, gait analysis was performed for 1 minute. The mean values of the differences in the step length, angle of COP, separation line standard deviation and step force of the lower legs affecting walking symmetry were calculated for treadmill walking and treadmill walking using the metronome. The Shapiro-Wilk test was used to test the normality of the collected data and a paired t-test was performed to analyze the difference in walking before and after using the metronome. RESULTS: As a result of the analysis, the mean of difference between the measured values of the bilateral lower extremity for step length, angle of COP, separation line standard deviation and step force were statistically significant before and after treadmill walking using the metronome. CONCLUSION: Therefore, the treadmill walking training using the metronome is effective in decreasing the difference in the foot width, gait angle, gait distribution, and foot pressure. Because of this, the treadmill walking training using the metronome has a significant effect on walking symmetry among the elements for correct walking, which is a means for enabling efficient and continuous walking.

• Journal of Internet Computing and Services
• /
• v.18 no.4
• /
• pp.19-25
• /
• 2017

In this paper, we designed and implemented IoT sensors based badminton motion analysis and training system that can be readily used by badminton players with PC. Unlike the traditional badminton training system which uses signals of the flags by coach, the proposed electronic training system used IoT sensors to automatically detect and analysis the motions for badminton players. The proposed badminton motion analysis and training system has the advantage with low power, because it communicates with the program through BLE communication. The badminton motion analysis system automatically measures the training time according to the player's movement, so it is possible to collect objective result data with less errors than the conventional flag signal based method by coach. In this paper, training data of 5 athletes were collected and it provides the feedback function through the visualization of each section of the training results by the players which can enable the effective training. For the weakness section of each player, the coach and the player can selectively and repeatedly perform the training function with the proposed training system. Based on this, it is possible to perform the repeated training on weakness sections and they can improve the response speed for these sections. Continuous research is expected to be able to compare more various players' agility and physical fitness.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.75-85
• /
• 2006

In recent geotechnical engineering, geothermal approach has been on the horizon to deal with geoenvironmental issues, freezing and thawing problems, and seepage phenomenon in dams and embankments. In this study, geothermal characteristic through inner body of dams and its influence on the seepage flow were experimented by lab test and field instrumentation. Also, one of up-to-date temperature monitoring technique, called as multi-channel thermal line sensing, was evaluated its availability. As a result of lab test, it is found that the seepage flow has influence on the geothermal characteristic and a potential of finding phreatic line and seepage fluctuation could be possible by continuous temperature monitoring using thermal line sensing skills. These kine of geothermal information could be available to the modelling of water geo-structure interaction. Out of short-term field tests, clear water table and temperature distribution of a dam were easily found through temperature monitoring in holes located near a reservoir and holes within a depth of constant temperature layer. However, it is also found that the geothermal flow and finding seepage line could not be easily understandable through multi-channel temperature monitoring because of the existence of constant temperature field, thermal conductivity of soils and rocks, and unsaturated characteristics of geo-material. In this case, long-term geothermal monitoring is recommended to find sudden fluctuation of seepage line and amount of leakage.

• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.440-445
• /
• 2013

This paper proposes a local estimation system which combines Cell Divide Algorithm with low-cost GPS/INS fused by Extended Kalman Filter(EKF) for localization of Quad-rotor when it returns to the departure point. In the research, the low-cost GPS and INS are fused by EKF to reduce the local error of low-cost GPS and the accumulative error of INS due to continuous integration of sensor error values. When the Quad-rotor returns to the departure point in the fastest path, a moving path can be known because it moves straight, where Cell Divide Algorithm is used to divide moving route into the cells. Then it determines the closest position of data of GPS/INS system fused by EKF to obtain the improved local data. The proposed system was verified through comparing experimental localization results obtained by using GPS, GPS/INS and GPS/INS with Cell Divide Algorithm respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.8
• /
• pp.1023-1028
• /
• 2010

Recently, an intelligent service robot is being developed for use in guiding and providing information to visitors about the building at public institutions. The intelligent robot has a sensor at the bottom to recognize its location. Four wheels, which are arranged in the form of a lozenge, support the robot. This robot cannot be operated on uneven ground because its driving parts are attached to its main body that contains the important internal components. Continuous impact with the ground can change the precise positions of the components and weaken the connection between each structural part. In this paper, the design of the suspension system for such a robot is described. The dynamic model of the robot is created, and the driving characteristics of the robot with the designed suspension system are simulated. Additionally, the suspension system is optimized to reduce the impact for the robot components.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.1
• /
• pp.68-76
• /
• 2011

Acoustic emission(AE) has emerged as a powerful nondestructive tool to detect any further growth or expansion of preexisting defects or to characterize failure mechanisms. Recently, this kind of technique, that is an in-situ monitoring of inside damages of materials or structures, becomes increasingly popular for monitoring the integrity of large structures like a huge wind turbine blade. Therefore, it is required to find a symptom of damage propagation before catastrophic failure through a continuous monitoring. In this study, a new damage location method has been proposed by using signal mapping algorithm, and an experimental verification is conducted by using small wind turbine blade specimen; a part of 750 kW real blade. The results show that this new signal mapping method has high advantages such as a flexibility for sensor location, improved accuracy, high detectability. The newly proposed method was compared with traditional AE source location method based on arrival time difference.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.65-73
• /
• 2012

Wrist wearable device for the measurement of pulse rate, ECG, and activity during normal daily life, which could be used for the continuous monitoring and remote transmission of acquired data, was developed. Pressure sensor, device attached electrodes, and 3-degree accelerometer were used. Analysis algorithm and firmware program were established for providing diagnostic information for the users. Results of this study, possible for the management of health report and transmission of the results through bluetooth by wearing simple personal wrist device, could be used for the development of portable device in the u-healthcare environment.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.583-589
• /
• 2019

We report experimental results on 940-nm 350-mW AlGaAs/InGaAs transverse single-mode laser diodes (LDs) adopting graded-index separate confinement heterostructures (GRIN-SCH) and p,n-clad asymmetric structures, with improved temperature and small-divergence beam characteristics under high-output-power operation, for a three-dimensional (3D) motion-recognition sensor. The GRIN-SCH design provides good carrier confinement and prevents current leakage by adding a grading layer between cladding and waveguide layers. The asymmetric design, which differs in refractive-index distribution of p-n cladding layers, reduces the divergence angle at high-power operation and widens the transverse mode distribution to decrease the power density around emission facets. At an optical power of 350 mW under continuous-wave (CW) operation, Gaussian narrow far-field patterns (FFP) are measured with the full width at half maximum vertical divergence angle to be 18 degrees. A threshold current (I_th) of 65 mA, slope efficiency (SE) of 0.98 mW/mA, and operating current (I_op) of 400 mA are obtained at room temperature. Also, we could achieve catastrophic optical damage (COD) of 850 mW and long-term reliability of 60℃ with a TO-56 package.

• 전자공학회논문지 IE
• /
• v.45 no.3
• /
• pp.27-35
• /
• 2008

In this paper, we propose a minute signal detection algorithm for a development of optical analyzer, using the non-dispersive infrared method with multi gas filter correlation wheel, that can measure various environmental air-pollution materials (CO, SO2, NOx, etc.) in real-time. The MCT(mercury cadmium telluride) sensor can detect minute signals those show and absorption characteristic of each environmental pollution materials. In the proposed method, a corresponding data of each environmental pollution materials can be separated by an external trigger and threshold values in the measured continuous signals.