• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.179-188
• /
• 2009

WIG crafts are a high speed vessel with features of dynamic supported craft. These crafts, which are predominantly of light weight and operate any substantially greater speeds than conventional craft such as bulk carrier, tanker, container ship, etc., could not be accommodated under traditional maritime safety instruments. It means that there is the need for risk and safety levels to be assessed on a holistic basis, recognizing that high levels of operator training, comprehensive and thoroughly implemented procedures, high levels of automation and sophisticated software can all make significant contributions to risk reduction. To response this requirement, the Interim Guideline for WIG craft(MSC/Circ.1054) were developed in the view of the configuration of WIG craft, which fall between the maritime and aviation regulatory regimes. This paper reviews a safety assessment process and methodology to be used in the design phase of a new ship. The process and methodology is based on the risk-based approach and is applied to safety assessment in concept development phase of small WIG craft in the 20-person class.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.2
• /
• pp.125-131
• /
• 2017

In order to develop test and performance analysis techniques for a CRP propulsion, a CRP dynamometer which can be installed inside the model ship was designed and manufactured. The object ship was the 16000TEU container carrier, which has test results for the single propeller. The design concept of the present CRP is that forward & after propellers have the same power ratio and their RPM ratio is 0.75:1. To begin with, we checked the performance of the CRP dynamometer through the calibration and then installed it inside the model ship. After the model ship setup including the design CRP and the rudder in the Large Cavitation Tunnel(LCT), a series of model tests composed of power ratio check, propeller behind wake(PBW) test, cavitation observation and pressure fluctuation tests was conducted. Through the model test and data analysis for CRP, the experimental technique was established and the improved method for CRP design was suggested.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.4
• /
• pp.235-242
• /
• 2016

In general, ship hull form design is carried out in two stages. In the first stage, the longitudinal variation of the sectional area curves is adapted from a similar mother ship to determine the volume distribution in ships. At this design stage, the initial design conditions of displacement, longitudinal center of buoyancy, etc. are satisfied and the global hydrodynamic properties of the structure are optimized. The second stage includes the local designing of the sectional forms. Sectional forms are related to the local pressure resistance in the fore- and aft-body shapes, cargo boundaries, interaction between the hull and propeller, etc. These relationships indicate that the hull sections need to be optimized in order to minimize the local resistance. The volumetric balanced (VOB) variation of ship hull forms has been suggested by Kim (2013) as a generalized, systematic variation method for determining the sectional area curves in hull form design. This method is characterized by form parameters and is based on an optimization technique. This paper emphasizes on an extensional function of the VOB considering a geometrical wave profile. We select a container ship and an LNG carrier to demonstrate the applicability of the proposed technique. Through analysis, we confirm that the VOB method, considering the geometrical wave profile, can be used as an efficient tool in the hull form design for ships.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.2
• /
• pp.76-85
• /
• 2023

The present study aims to review the wave pattern resistance analysis method suggested by the International Towing Tank Conference. From the experimental database of a container carrier ship model, the wave pattern measurement and resistance test results are utilized. The wave pattern resistance at the design Froude number is obtained to be compared with the wave making resistance of experiments. Wave pattern resistance is lower than wave making resistance by 1978 ITTC and uniform regardless of transverse location of wave cut. The method is also applied to the wave height field by Computational Fluid Dynamics (CFD) analyses with Froude number variation. Although numerical damping suppressed waves in downstream, waves around the hull and wave pattern resistance are properly predicted.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.3
• /
• pp.146-154
• /
• 2023

Efforts have been made to reduce the greenhouse gas emissions from ships by limiting the energy efficiency index, and net zero CO₂ emission was proposed recently. The most ideal measure to achieve zero emission ship is electrification, and fuel cells are considered as a practical power source of the electrified propulsion system. The electric efficiency in the electrochemical reaction of fuel cells can be achieved up to 60% practically. The remaining energy is converted to heat energy but most of them are dissipated by cooling. In the author's previous research, a hybrid propulsion system utilizing not only electricity but also heat was introduced by combining electric motor and steam turbine. In this article, long term efficiency is evaluated for the introduced hybrid propulsion system by considering a virtual 24,000 TEU class container carrier model. To reflect a more practical operating condition, the actual navigation data of a similar real ship in the real world were collected from automatic identification system data and applied. From the result, the overall efficiency of the hybrid propulsion system is expected to be higher than a conventional electric propulsion fuel cell ship by 30%.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.4
• /
• pp.226-235
• /
• 2024

A method for quantifying the adaptability of ship maneuver scenarios for data-driven modeling of ship dynamics is developed based on the principal component analysis. A random maneuver scenario is suggested as a reference for ship dynamics, which can obtain the converged principal components of ship dynamics features by the Monte Carlo simulation. Principal components of conventional maneuver scenarios defined by the International Maritime Organization (IMO) are compared to that of the random maneuver. A conventional ship dynamics model for a container carrier vessel for four degrees of freedom dynamics is introduced to simulate the random and IMO maneuver scenarios. It is confirmed that the IMO tests follow the tendency of random maneuver scenario in terms of execution time and adaptability.

• Horticultural Science & Technology
• /
• v.18 no.5
• /
• pp.612-620
• /
• 2000

In developing soil wetting agent using polyoxyethylene octylphenyl ether [$C_8H_{17}O(C_2H_4O)_{10}H$, POE], the effect of mixtures of POE and polyoxyethylene+polypropyleneoxide tridecylether (1:1, w/w, CM-1), polyoxyethylene+polypropyleneoxide tridecylether+propyleneglycol monomethylether (1:1:2, w/w/w, CM-2) or glycerin+ditridecyl phthalate (1:1, w/w, CM-3) on changes of concentration of POE, initial wetting, evaporative water loss, water infiltration, and changes of physical properties in root media were determined. The mixtures of POE and CM-1, 2, or 3 with zeolite or vermiculite as carrier had high concentrations of POE in root media during 6 elution times, but those after 6 times decreased rapidly indicating unstable elution of POE. The commercial AquaGro was more effective than the mixtures of POE+CM-1, 2, or 3 in water retention during 18 hours. Root media incorporated with POE+CM-2 held more water than any other treatments at 84 hours after watering, but the differences among treatments except control were not significant. In the treatments with zeolite as a carrier, POE+CM-3 had the greatest evaporative water loss followed by POE+CM-2, AquaGro, control, and POE+CM-2. In the treatments with vermiculite as a carrier, POE+CM-1 had the highest evaporative water loss followed by POE+CM-3, AquaGro, control, and POE+CM-2. In the effect of mixtures with zeolite as a carrier on infiltration of water into root media, the treatment of POE+CM-1 had the highest amount of water infiltrated followed by POE+CM-3, AquaGro, POE+CM-2, and control. In the effect of mixtures with vermiculite as a carrier on infiltration of water into root media, the treatment of POE+CM-3 had the highest amount of water infiltrated followed by AquaGro, POE+CM-1, POE+CM-2, and control.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.6
• /
• pp.11-51
• /
• 1993

This study is focused on the problems and the suggestions of proper ideas for solving them which are arisen from appling CIF, Incoterms 1990 into the contract of sale after reviewing of the contents of traditional CIF contract and the main changes of CIF, Incoterms 1990. This study summerized as follows: First, when the seller provide the buyer with non-negotiable sea waybill or inland waterway document instead of negotiable bill of lading, it is my feeling that the essence of symbolic delivery in traditional CIF contract is fading. And if the buyer has paid for the goods in advance, or a bank wishes to use the goods as security for a loan extended to the buyer, it is not sufficient that the buyer or the bank be named as consignee in a non-negotiable document. This is true because the seller by new instractions to the carrier could replace the named consignee with someone else. To protect the buyer or the bank it is therefore necessary that the original instructions from the seller to the carrier to deliver the goods to the named consignee be irrevocable. Second, CIF term can only be used for sea and inland waterway transport. When the ship's rail serves no practical purposes such as in the case of roll-on/roll-off or container traffic, CIP term instead of CIF term is more appropriate to use. Third, the EDI method still contains many legal and technical problems to be solved in order to be used thoroughly' in the international sale of goods. Therefore, the parties wishing to replace the traditional paper-based trade documents by electronic messages must exchange the agreement on EDI each other in order to prevent and sol ye unexpected problems. Forth, it may be that the goods are to be carried in bulk without such marking or naming of consignee as would amount to appropriation. Then the risk will not pass until effective appropriation has been made. Therefore, the seller needs to appropriate by issuing of separate bills of lading or delivery orders for parts of the bulk cargo. And in case the goods are bought while they are carried at sea, some problems on the passing of risk would arise. One possibility is that the buyer might have to assume risks which have already occured at the time when the contract of sale is entered into force. The other possibility would be to let the pissing of the risk concide with the time when the contract of sale is concluded. The parties are advised to ascertain the applicable law and any solution which might follow there form. Finally, Incoterms are restricted to deal with the main principles for the division of functions, costs and risks between the parties and the rest is left to their individual contract as supplemented by the custom of the trade, the individual terms of the contract of sale and the applicable law. Thus, the parties are advised to ascertain the applicable law on their individual contract of sale in order to solve the problems on the transfer of property, the remedy and so on.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.1
• /
• pp.1-10
• /
• 1997

Viscous flow around actual ship is calculated by an use of RANS equations. The propriety of this computing method, usefulness to hull form design and the scale effect which is the effect of viscous flow depending on the scale of ship model are investigated. Reynolds stress is modelled by using k-${\varepsilon}$ turbulence model and the law of wall is applied near the body. Body fitted coordinates are introduced for the treatment of the arbitrary 3-dimensional shape of the ship hull form. The transformed equations in the computational domain are numerically solved by an employment of FVM. In the calculation of pressure, SIMPLE method is adopted and the solution of the discretized equation is obtained by the line-by-line method with the use of TDMA The calculations of two ships, 4410 TEU container carrier and 50,000 DWT class bulk carrier, are performed at model and actual ship scale. The results are compared and discussed with the model test results which are viscous resistance, nominal wake distribution at propeller plane and limiting streamline on the hull surface. They describe the effect of stem form and the scale effect very well. In particular, the calculated nominal wake distribution and limiting streamline are agreed qualitatively with the experiments and the viscous resistance values are estimated within ${\pm}5%$ difference from the resistance tests.

• Journal of Navigation and Port Research
• /
• v.37 no.1
• /
• pp.1-7
• /
• 2013

In this paper the developed prediction technique of wave-making resistance performance for a ship attached with a vertical blade had been verified. Numerical analysis program as a prediction technique had been developed using the Rankine source panel method and the vortex lattice method(VLM). The nonlinearity of the free surface conditions was fully taken into account using the iterative method and the trim and the sinkage of the ship were also considered in the numerical analysis program. Panel cutting method was applied to get hull surface panels. Numerical computations were carried out for a 4000TEU container carrier and the vertical blade was attached 6 different locations astern. To investigate the validity of the numerical analysis program the commercial viscous flow field analysis program FLUENT was used to obtain the viscous flow field around the ship and the model test was performed. The model test results were compared with the numerical analysis results.