• 대한화장품학회지
• /
• 제31권3호
• /
• pp.253-257
• /
• 2005

피부노화의 정도를 판정하기 위해 사용되는 주름측정법들은 객관성과 재현성의 확보가 중요한 요소이다. 최근의 경향은 주름의 형태나 깊이에 주는 영향을 최소화하기 위해 주름 측정시 피부에 직접 기계나 도구를 접촉하지 않고 측정하는 비접촉식 측정방법으로 빠르게 전환되고 있는 상황이다. 저자들은 주름측정 기술의 변천 과정을 간단히 살펴보고, 비접촉식 fringe projection 방식의 미세주름 측정기기인 PRIMOS를 중심으로 측정원리, 특징들을 접촉식 측정방법인 모사판을 이용한 방법과 비교하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.929-932
• /
• 2005

We report a pull-up type RF MEMS switch using double electrode without elastic deformation of the cantilever involved in the actuation. At a voltage of 4.5 V, reliable actuations are achieved such that the movable lower contact pad is pulled up by the electrostatic force to make contact with the upper pad. At a frequency of 50 GHz, an insertion loss of 0.7 dB and an isolation of 50.7 dB are obtained from the switch. The measured transient times for switch-on and switch-off are 120 and 80 us, respectively.

• 한국운동역학회지
• /
• 제21권2호
• /
• pp.231-241
• /
• 2011

The purpose of this study was to analyze the distribution of foot pressure generated by active materials of a functional insole. Comfort is an important consideration while selectingfootwear and insoles. Consequently, it has an influence on injury. The development of new materials for functional insoles is considered one of the more important points for their manufacture. The method adopted in this study is as follows. First, ten healthy males were selected as subjects for the study. Each subject's foof was pre-screened podoscope(Alfoots, Korea) to check for the presence of any foot abnormalities, Two kinds of equipment were used for the study: a foot pressure device from Pedar-X, Germany, and a treadmill from Pulsefitness, UK. Next, each subject was asked to test four types of insoles(insoles of outdoor shoes, indoor shoes, walking shoes, and sports shoes) via walking trials on the treadmill at a constant speed of 4.2 km/h. The pressure distribution data(contact area, maximum force, maximum peak pressure, and maximum mean pressure) was collected using the pressure device at a sampling rate of 100 Hz. Results of the tests showed that all four types of functional insoles increased contact areas whit the foot. Further, functional insoles of walking shoes and sport shoes decreased the foot pressure. From these results, we conclude that the active materials of functional insoles of shoes can increase the contact area and provide greater comfort.

• Tribology and Lubricants
• /
• 제20권2호
• /
• pp.51-57
• /
• 2004

Micro/nano adhesion and friction properties of mixed self-assembled monolayer (SAM) with different chain length for MEMS application were experimentally studied. Many kinds of SAM having different spacer chains(C6, C10 and C18) and their mixtures (1:1) were deposited onto Si-wafer, where the deposited SAM resulted in the hydrophobic nature. The adhesion and friction properties between tip and SAM surfaces under nano scale applied load were measured using an atomic force microscope (AFM) and under micro scale applied load were measured using ball-on-flat type micro-tribotester. Surface roughness and water contact angles were measured with SPM (scanning probe microscope) and contact anglemeter. Results showed that water contact angles of mixed SAMs were similar to those of pure SAMs. The morphology of coating surface was roughened as mixing of SAM. Nano adhesion and nano friction decreased as increasing of the spacer chain length and mixing of SAM. Micro friction was decreased as increasing of the spacer chain length, but micro friction of mixed SAM showed the value between pure SAMs. Nano adhesion and friction mechanism of mixed SAM was proposed in a view of stiffness of spacer chain modified chemically and topographically.

• Transactions on Electrical and Electronic Materials
• /
• 제7권4호
• /
• pp.167-172
• /
• 2006

Submicron colloidal silica coated with ceria were prepared by mixing of silica and nano ceria particles and modified by hydrothermal reaction. The polishing efficiency of the ceria coated silica slurry was tested over oxide film on silicon wafer. By changing the polishing pressure in the range of $140{\sim}420g/cm^2$ with the ceria coated silica slurries in $100{\sim}300nm$, rates, WIWNU and friction force were measured. The removal rate was in the order of 200, 100, and 300 nm size silica coated with ceria. It was known that the smaller particle size gives the higher removal rate with higher contact area in Cu slurry. In the case of oxide film, the indentation volume as well as contact area gives effect on the removal rate depending on the size of abrasives. The indentation volume increase with the size of abrasive particles, which results to higher removal rate. The highest removal rate in 200 nm silica core coated with ceria is discussed as proper combination of indentation and contact area effect.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2007년도 동계학술연구발표회 및 스핀트로닉스와 나노물리에관한 국제심포지움
• /
• pp.124-125
• /
• 2007

• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.1928-1937
• /
• 2003

Effect of elastic modulus mismatch on the contact crack initiation is investigated to find major parameters in designing desirable surface-coated system. Silicon nitride coated soft materials with various elastic modulus mismatch, E$\_$c//E$\_$s/＝1.06∼356 are prepared for the analysis. Hertzian contact test is conducted for producing contact cracks and the acoustic emission detecting technique for measuring the critical load of crack initiation. The implication is that coating thickness and material strength are controllable parameters to prevent the initiation of contact cracks resulted from the elastic modulus mismatch in the hard ceramic coating layer on the soft materials.

• Tribology and Lubricants
• /
• 제24권5호
• /
• pp.228-233
• /
• 2008

In this study, the methodology for determination of shoulder height in the internal shape design of ball bearing using 3D contact analysis is proposed. The static analysis of a ball bearing was performed to calculate the distribution of applied contact load and angles among the rolling elements. From each rolling element loads and the contact geometry between ball and inner/outer raceway, 3D contact analyses using influence function are conducted. These methodology is applied to HDD ball bearing. A critical axial load and a critical shoulder height which are not affected by edge are calculated. The proposed methodology may be applied to other rolling element bearing for the purpose of reducing the material cost and improving the efficiency of the bearing design process.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.55-56
• /
• 2002

Nanotribological characteristics of hydrophobic surfaces were studied experimentally using an atomic force microscope (AFM). Two kinds of thiolic self-assembled monolayers (SAM) having different spacer chains and their mixture were deposited onto gold-coated mica, where the deposited SAM resulted in the hydrophobic nature. Results showed that the mixed thiolic SAMs resulted in low adhesion and friction in nano-scale contact. It was argued that the water wetting characteristics played a central role on nano-scale adhesion and friction. Also the effect of mixing the thiolic SAMs were discussed on the basis of real area on contact and the stiffness of the SAM layers.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.387-388
• /
• 2008

In this paper, we have designed and fabricated hyperabrupt varactor diodes. Capacitance variations of hyperabrupt-doped varactor diodes are larger than those of uniform-doped varactor diodes. The measured reverse breakdown voltage of the fabricated varactor diodes was about 20 V. For the anode contact diameter of $50\;{\mu}m$, the maximum capacitance of the fabricated varactor diode was 2.1 pF and the minimum capacitance 0.44 pF. Therefore, the $C_{max}/C_{min}$ ratio was 4.77. Also, for the anode contact diameter of $60\;{\mu}m$, the maximum and minimum capacitances were 2.9 and 0.62 pF, respectively. And, thus, the $C_{max}/C_{min}$ ratio was 4.64.