• Tribology and Lubricants
• /
• v.26 no.2
• /
• pp.136-141
• /
• 2010

In an oil hydraulic vane pump for an automobile, it is very important that the vane doesn't separate from the camring inner race during the operation of the vane pump. The vane generally has not only the oil hydraulic force acting on the bottom face to contact to camring inner race but there is also an inertial force and viscous force. Because the oil hydraulic force is much larger than the other forces, the contact state between the vane tip and the camring inner race is sufficient. However, the contact state between the vane tip and the camring inner race is only affected by the inertial and viscous forces during the delivery of the vane pump, because the oil hydraulic force acting on the vane is in equilibrium. If the inertial force is larger than the viscous force, which happens when the vane is separated from the camring inner race, the delivery of the vane pump can become unstable or the volume efficiency can become decrease rapidly. Therefore, in this paper, the state of the contact between the vane and the camring is considered. The results show that the rotating speed of the shaft, the operating temperature of the oil, the clearance between the vane and the rotor, and the mass of the vane exert a great influence on the state of the contact between the vane and the camring.

• Korean Journal of Materials Research
• /
• v.26 no.10
• /
• pp.556-560
• /
• 2016

Using current-voltage (I-V) and capacitance-voltage (C-V) measurements, the electrical properties of Au and Cu Schottky contacts to n-Ge were comparatively investigated. Lower values of barrier height, ideality factor and series resistance were obtained for the Au contact as compared to the Cu contact. The values of capacitance showed strong dependence on the bias voltage and the frequency. The presence of an inversion layer at the interface might reduce the intercept voltage at the voltage axis, lowering the barrier height for C-V measurements, especially at lower frequencies. In addition, a higher interface state density was observed for the Au contact. The generation of sputter deposition-induced defects might occur more severely for the Au contact; these defects affected both the I-V and C-V characteristics.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.1
• /
• pp.60-65
• /
• 2004

A flexible tactile sensor away with 8 H 8 tactile elements is designed and fabricated. The material of the sensor is PVDF(polyvinylidene fluoride) film and flexible circuitry is used in the fabrication fur the flexibility of the sensor The experimental results on static and dynamic properties of the sensor are obtained and examined. The signals of a contact pressure to the sensor are sensed and processed in the DSP system in which the signals are digitalized and filtered. The processed signals of the sensor outputs are visualized in a personal computer for illustrating the shape and force distribution of a contact object. The reasonable performance for the detection of contact state is verified through sensing examples.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.11
• /
• pp.1136-1141
• /
• 2014

This paper proposes a new contact type ball tracking sensor to improve the control performance of a low cost ball-and-beam system. It is well-known that the impulsive measurement noise contained in ball position measurement is one of the factors which severely degrades the ball-and-beam control performance. The impulsive ball position measurement noises often appear under the sporadical ball floating on the beam. This fact motivates us to devise a simple analog preprocessing circuit to determine whether the ball loses the contact or not. Once the abnormal ball position measurement is detected, the design problem of the ball tracking sensor can be cast into the typical state estimation problem with missing data. In order to tackle the real-time implementation issue, a steady-state Kalman filter is applied to the problem. Through the experimental results, the usefulness of the proposed scheme is demonstrated.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.82-84
• /
• 2003

In case contact between point of contacts is not achieved well, contact resistance is grown, and by current concentration at current conducting contacts can weld. In order to decrease contact resistance between contacts in case of busbar, installing spring between fixed contact and moving contact. and then force on faying surface of contacts increase and contact resistance decrease. But, in case increase force of spring to widen contact area, operating force moving contact can grow, on the contrary force of spring is small, contact resistance becomes low. Therefore, need to optimize force and number of spring. position, and also need to examine force change on contact surface at point of contact moving. In this paper, dynamic kinetics analysis for force on faying surface of contacts is performed at unsteady state. It is showed to not uniform force on surface between contacts, and we can got more uniform force by means of change spring position.

• Structural Engineering and Mechanics
• /
• v.66 no.1
• /
• pp.15-25
• /
• 2018

Post-construction subgrade settlement especially differential settlement, has become a key issue in construction and operation of non-ballasted track on high-speed railway soil subgrade, which may also affect the dynamic performance of passing trains. To estimate the effect of differential subgrade settlement on the mechanical behaviors of the vehicle-slab track system, a detailed model considering nonlinear subgrade support and initial track state due to track self-weight is developed. Accordingly, analysis aiming at a typical high-speed vehicle coupled with a deteriorated slab track owing to differential subgrade settlement is carried out, in terms of two aspects: (i) determination of an initial mapping relationship between subgrade settlement and track deflections as well as contact state between track and subgrade based on a semi-analytical method; (ii) simulation of dynamic performance of the coupled system by employing a time integration approach. The investigation indicates that subgrade settlement results in additional track irregularity, and locally, the contact between the concrete track and the soil subgrade is prone to failure. Moreover, wheel-rail interaction is significantly exacerbated by the track degradation and abnormal responses occur as a result of the unsupported areas. Distributions of interlaminar contact forces in track system vary dramatically due to the combined effect of track deterioration and dynamic load. These may not only intensify the dynamic responses of the coupled system, but also have impacts on the long-term behavior of the track components.

• Food Science of Animal Resources
• /
• v.42 no.2
• /
• pp.313-320
• /
• 2022

Brazil is considered as a great broiler feet exporter, especially for the Chinese trade. Contact lesions at the tibiotarsal region are responsible for economic losses and there is no model for its classification, thereby this study presents a fast and practical grade system to be used in the poultry industry and proposes these lesion characterizations into three different grades. For this, correlation was made between macroscopic, histological findings and microbiological quantification (Escherichia coli, Staphylococcus spp., Streptococcus spp. and sulphite-reducing clostridia) from contact lesions in the tibiotarsal region of 112 broiler carcasses, divided in four groups (n=28), accordingly to the lesion's intensity. There were no significant differences in microbiological quantification among the groups (p>0.05) except for the grade 3 group, as grade 1 and 2 lesions were in the early stages and histopathological changes such as ulceration were not observed. In grade 3 lesion group, it was observed bacterial cocci grume and ulceration at the articular region and significantly higher microbiological count (p<0.05) for E. coli and Staphylococcus spp. In conclusion, the visual standard proposed in this work, correlated and confirmed by the histopathologic, and microbiologic characterization, allows to precise and fast ascertainment of the contact lesion grade in the tibiotarsal regions of broiler carcasses. Moreover, it should be highlighted that grades 1 and 2 alterations are not caused by an inflammatory process caused by pathogenic agents and should not be considered a public health risk.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.56-63
• /
• 1995

MESFETs of the Ti/Au and Ti/Pd/Au gate were fabricated on n-type GaAs. Interdiffusion at Schottky interfaces, Schottky contact properties, and MESFET characteristics with heat treatment were investigated. Ti of Ti/Au contact and Pd of Ti/Pd/Au contact acted as a barrier metal against interdiffusion of Au at >$220^{\circ}C$. Pd of Ti/Pd/Au contact acted as a barrier metal even at >$360^{\circ}C$, however, Ti of Ti/Au contact promoted interdiffusion of Au instead of role of barrier metal. As the heat treatment temperature increases, in the case of both contact, saturated drain current and pinch off voltage decreased, open channel resistance increased, and degree of parameter variation in Ti/Au gate was higher than in Ti/Pd/Au gate at >$360^{\circ}C$ Schottky barrier height of Ti/Au and Ti/Pd/Au contacts was 0.69eV and 0.68eV in the as-deposited state, respectively, and Fermi level was pinned in the vicinity of 1/2Eg. As the heat treatment temperature increases, barrier height of Ti/Pd/Au contact increased, however, decreased at >$360^{\circ}C$ in the case of Ti/Au contact. Ideality factor of Ti/Au contact was nearly constant regardless of heat treatment, however, increased at >$360^{\circ}C$ in the case of Ti/Au contact. From the results above, Ti/Pd/Au was stable gate metal than Ti/Au.

• Tribology and Lubricants
• /
• v.25 no.2
• /
• pp.86-95
• /
• 2009

Adhesion tests were carried out in order to investigate the effect of temperature on the adhesion behavior between a PMMA film and a fused silica lens in the micro scale. For the tests, a microtribometer system was specially designed and constructed. The pull-off forces on the PMMA film were measured under atmospheric condition as the temperature of the PMMA film was increased from 300 K to 443 K and decreased to 300 K. The contact area between the PMMA film and the lens was observed during the test. The adhesion behavior was changed with the change of the PMMA surface state as the temperature increased. In glassy state below 363 K, the pull-off force did not change with the increase of temperature. In rubbery state from 383 K to 413 K, the pull-off force increased greatly as the temperature increased. In addition, the area of contact was enlarged. In viscous state above 423 K, the fingering instability was observed in the area of contact when the PMMA film contacted with the lens. It was also found that the adhesion behavior can be varied with the thermal history of the PMMA film. The residual solvent in the PMMA film could emerge to the PMMA surface due to the heating and reduced the pull-off force.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3_1spc
• /
• pp.544-550
• /
• 2013

A grooved surface with anisotropic wettability was fabricated on a silicon substrate using photolithography, reactive ion etching, and a KOH etching process. The contact angles (CAs) of water droplets were measured and compared with the theoretical values in the Cassie state and Wenzel state. The experimental results showed that the contact area between a water droplet and a solid surface was important to determine the wettability of the water. The specimens with native oxide layers presented CAs ranging from $71.6^{\circ}$ to $86.4^{\circ}$. The droplets on the specimens with a native oxide layer could be in the Cassie state because they had relatively smooth surfaces. However, the CAs of the specimens with thick oxide layers ranged from $33.4^{\circ}$ to $59.1^{\circ}$. This indicated that the surface roughness for a specimen with a relatively thick oxide layer was higher, and the water droplet was in the Wenzel state. From the CA measurement results, it was observed that the wetting on the grooved surface was anisotropic for all of the specimens.