• Journal of Korean Society of Water and Wastewater
• /
• v.29 no.2
• /
• pp.261-269
• /
• 2015

In this study, we applied a membrane distillation process to investigate a feasibility of treating a wastewater with high concentration of organic matters including nitrogen and phosphorus. The laboratory scale experiment was performed by using a hydrophobic PVDF membrane with the pore size of $0.22{\mu}m$ and porosity of 75%. The installation was direct contact type where the temperature difference between a feed and permeate side was controlled to have a range from 20 to $60^{\circ}C$. We observed a flux variation and a concentration changes of COD, $PO{_4}^{3-}$-P, $NH_4{^+}$-N and conductivity of feed side as well as permeate side with various temperature differences (20 to $60^{\circ}C$), cross flow velocities (0.09 to 0.27 m/s) through the module, and pH (6.6 to 12.0) of the feed that has the initial concentration of COD about 1,000 mg/L, total nitrogen 390 mg/L, total phosphorus 10 mg/L, conductivity of $7,000{\mu}s/cm$. The results showed that the average flux was ranged from 4 to $40L/m^2/hr$ which was almost similar with the flux of NaCl and deionized water used as a feed solution. The lowest flux was obtained at the operating condition with the temperature difference of $20^{\circ}C$ and cross flow velocity of 0.09 m/s while the highest one was measured with $60^{\circ}C$ and 0.27 m/s. Above 99% of COD and $PO{_4}^{3-}$-P in the feed could be rejected regardless of an operating condition. However, the removal rate of ammonium nitrogen was varied from 64 to 99% depending on the pH of feed solution.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.1
• /
• pp.64-72
• /
• 2007

Humans are exposed by a range of pollutants in soil via exposure routes such as ingestion, inhalation, and dermal contact. Risk assessment is a process of evaluating the adverse health effects of chemicals as a result of exposure to stressors, and it is a very useful tool to establish the cleanup goals in contaminated lands. In the exposure assessment that is one of main process in risk assessment, exposure factor plays a significant role to quantify the intake of soil pollutants. However there is a very limited study about the exposure factor applicable to Korea. In this study, we compared the exposure factors applied by the developed countries including the United States and representative European countries, and suggested the exposure factor that might be suitable in our situation. The exposure factors considered in this study include average lifetime, body weight, (exposed) skin surface area, life time, skin absorption, soil-skin adherence factor, and soil ingestion rate. This information is needed to quantitatively estimate the intake of soil pollutants in contaminated lands.

• Journal of Conservation Science
• /
• v.26 no.2
• /
• pp.149-156
• /
• 2010

One of resins, V-Flon is useful as a coating material because YK-D80, which is a solvent for V-Flon, is not highly volatile. However, it can not completely harden and can flow out when metal artifacts are joined and restored in the process of the treatment. Therefore, after the impregnation process in order to accelerate the hardening speed of a coating material, usually a dry oven was adopted. This study focused on finding the problems on the dry oven which is employed to increase the speed and investigating the most effective solvent and its composition by checking any change occurred depending on the concentration of solvents. Six different types of solvents were selected and samples were prepared in a manner that they were impregnated with solvents in three concentrations respectively (10%, 20%, 30%). To determine the condition of the samples, the stability evaluation was performed by measuring the change of color and the gloss, the thickness of coated layers, the corrosion after coating, the water resistance by contact angles. Through the comparative experiments between the natural drying and the artificial drying using a dry oven, it was found that when the dry oven is used, some problems are identified on the point of forming a uniform and stable layer because of the unstable data collected from the forced artificial dry. The experiments performed using 3 different concentration rates (10%, 20%, 30%) presented that in the case of 10% V-Flon in Xylene (using as a solvent), its layer was thin as well as it showed the high water-barrier property, which allows it to form the stably coated layer with the lower gloss and color change.

• Journal of the Korean Society for Library and Information Science
• /
• v.29
• /
• pp.257-279
• /
• 1995

Cooperative program planning and teaching is a strategy for developing and implementing resource based learning. This approach combines the classroom teacher's subject expertise and knowledge of the students with the teacher­librarian's specialized knowledge of the availability and use of learning materials. And the purpose of cooperative program planning is to develop learning experiences or units of study that effectively integrate the student's resource center activities with other learning experiences. There are also some conditions that are conducive to effective planning sessions. First, the teacher-librarian must be prepared to initiate planning with teachers, rather than waiting for teachers to come to them. Second, the teacher-librarian must be prepared to present suggestions in such a way that the teacher can respond. The purpose of this study is (1) to investigate the planning process of cooperative program planning and teaching in the previous studies and (2) to find general problems when the cooperative program planning and teaching apply in actual situation. For these purposes, I chose a school library and a teacher-librarian in Seoul to observe how this cooperative program planning and teaching carry out in the school library. Main findings are summarized as follows: (1) A teacher who teaches alone for one grade is more proper to carry out the cooperative program planning and teaching. Young teachers are usually more active to change their teaching methods. (2) The cooperative program planning and teaching is a program what needs a lot of materials. When there is no right reference book in a school library, it would be good to access DB through PC telecommunication. It is also possile to contact lirarians who work in large public libraries or university libraries. (3) The cooerative program planning and teaching needs cooperative working between a teacher-librarian and a teacher. Thus a teacher-librarian should be in his school in the day time like the other teachers for the program's planning process. ( 4) There has to be a guide to change into resource based learning in teaching method. Thus the Korean Library Association or Korean Library and Information Science Society should offer a seminar or a workshop about cooperative program planning and teaching for the teacher-librarians. (5) It needs a system that a teacher-librarian can know about student's assignments so that he can prepare reference books for them. (6) The school library can be able to offer excellent service like cooperative program planning and teaching to the teachers and students according to a teacher-librarian's enthusiasm.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.3
• /
• pp.143-150
• /
• 2009

Fuel oil mostly used for a ship is made from crude oil by refining process. In order to produce plenty of high-quality fuel oil, the Fluid catalytic cracking(FCC) method is widely adopted to many refinery factories during the decomposition process from high molecule into lower molecule. The major constituents in spent FCC catalysts are Si, Al, Fe, Ti, alkali metals and some others. The spent catalyst is also composed small amounts of rare metals such as Ce, Nd, Ni and V. The big problem in FCC oil is mixing the catalyst in the oil. This reason is unstable separation of FCC catalyst in separator. Such a FCC catalyst will become a reason of heavy wear down in moving parts of engine. The impurity in oil is ash and deposit compound, such as Al, Si, Ni, Fe and V, which will accelerate the wear down on fuel pump, fuel injection valve cylinder liner and piston ring. It is important to find a basic reason of an engine trouble for preventing similar troubles anymore. Insurance compensation will be different according to the reason of an engine trouble which might be natural abrasion or other external causes. In this study, types and reasons of engine troubles related to fuel oil will be covered.

• Journal of Sensor Science and Technology
• /
• v.11 no.3
• /
• pp.155-162
• /
• 2002

The sensing properties of carbon monooxide were investigated as a function of mixing ratio and the lamination structure of 3mol% ZnO-doped $SnO_2$ and 3mol% $SnO_2$-doped ZnO. The lamination structures were fabricared monolayer, double layer, and hetero layer of $SnO_2$, Zno, and theirs mixture composition using thick film process. There was no second phase by the reaction of $SnO_2$ and ZnO. The conductance was decreased by the addition of ZnO in $SnO_2$, but it was increased with the addition of $SnO_2$ in ZnO. The conductance was increased with temperature and the inlet of CO. There was no improvement of sensitivity in the structure of mono- and double-layer. The hetero-layer structure, however, of $SnO_2$ 3ZnO-ZnO $3SnO_2$ showed the higher resistivity and the highest sensitivity. Ohmic characteristics was confirmed by the linear properties for I-V measurements.

• Journal of the Korean Geosynthetics Society
• /
• v.11 no.2
• /
• pp.31-38
• /
• 2012

The recycled aggregate for construction, slag, coal ash and such may elute leachates by chemical reaction when in touch with water, and to confirm this, generally the waste process test is executed. If the test result criteria are met, it can be used as replacement aggregate. In case of steel slag, however, the chemical reaction does not end in a short term, but occurs over a long time, generating eluted leachate. Thus, in this study, the leachate from steel slag were analyzed for heavy metal, and the pH change and environmental characteristics of eluted leachate were analyzed. According to the experiment result, the chemical reaction of free CaO and water within the steel slag occurred more actively when stirred, and the smaller the grain size, the higher the pH was. As the result of waste process test, all test items for the two types of specimen were found to have no heavy metal, but from the ICP test analysis result, heavy metals such as Al, Pb, Zn, Fe were detected. It could be confirmed that chemical reaction would occur upon contact of steel slag and water, and heavy metal may be detected depending on experiment conditions and analysis methods, the long-term environmental characteristics should be examined for utilization of steel slag.

• Korean Chemical Engineering Research
• /
• v.46 no.6
• /
• pp.1100-1106
• /
• 2008

In this study, we presented rapid and simple fabrication method of functionalized surface on various substrates as a universal platform for the selective immobilization of cells. The functionalized surface was achieved by using deposition of polyelectrolyte such as poly(allyamine hydrochloride) (PAH), poly(diallyldimethyl ammonium chloride) (PDAC), poly(4-ammonium styrene sulfonic acid) (PSS), poly(acrylic acid) (PAA) and fabrication of poly(ethylene glycol) (PEG) microstructure through micro-molding in capillaries (MIMIC) technique on each glass, poly(methyl methacrylate) (PMMA), polystyrene (PS) and poly(dimethyl siloxane) (PDMS) substrate. The polyelectrolyte multilayer provides adhesion force via strong electrostatic attraction between cell and surface. On the other hand, PEG microstructures also lead to prevent non-specific binding of cells because of physical and biological barrier. The characteristic of each modified surface was examined by using static contact angle measurement. The modified surface onto several substrates provides appropriate environment for cellular adhesion, which is essential technology for cell patterning with high yield and viability in the micropatterning technology. The proposed method is reproducible, convenient and rapid. In addition, the fabrication process is environmentally friendly process due to the no use of harsh solvent. It can be applied to the fabrication of biological sensor, biomolecules patterning, microelectronics devices, screening system, and study of cell-surface interaction.

• Korean Chemical Engineering Research
• /
• v.55 no.6
• /
• pp.798-806
• /
• 2017

A activated carbon (WCAC, waste citrus activated carbon) prepared from an agricultural waste citrus peel material generated in Jeju was utilized for the removal of dimetridazole (DMZ) antibiotics in aqueous solution. The adsorption of DMZ on WCAC was investigated with the change of various parameters such as contact time, dosage of WCAC, particle size of WCAC, temperature, pH, and DMZ concentration. The DMZ adsorption capacity increased with increasing temperature and decreasing particle size. Also it was decreased at less than pH 4 but sustained almost constantly at pH 4 or greater. Isotherm parameters were determined from the Langmuir, Freundlich, Redlich-Peterson and Duinin-Radushkevich (D-R) isotherm models. The isotherm data were best described by the Redlich-Peterson isotherm model. And the adsorption kinetics can be successfully fitted to the pseudo-second-order kinetic model. The results of the intra-particle diffusion model suggested that film diffusion and intra-particle diffusion were occurred simultaneously during the adsorption process. Meanwhile, the thermodynamic parameters indicated that the adsorption reaction of DMZ on WCAC was an endothermic and spontaneous process. The experimental results showed that WCAC is a promising and cheap adsorbent for the removal of DMZ antibiotics.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.86-91
• /
• 2004

$LiCoO_2$ cathode powders with round particle shaped and nano grain sized of 70-300nm were synthesized by a mechanochemical method. The surface of Li-Co precursor prepared by freeze drying method was modified by $K_2SO_4$ coating and ball milling was used for the coating process. The precursor was crystallized to high temperature form of $LiCoO_2$ at $800^{\circ}C$ and the grain growth was inhibited by the $K_2SO_4$ coating effect. The $K_2SO_4$ coating was not decomposed at $800^{\circ}C$ and prevented the contact in the Li-Co precursor particles. The nano-sized $LiCoO_2$ powder had tetragonal phase and it affected the Li diffusion through the surface of particles. It means that the anode materials for hight performance battery should be satisfied not only small particle size but phase contol on the surface of particles. In this study, the powder characteristics and rate capabilities were compared with a commercial powder and the nano-sized $LiCoO_2$ powder fabricated by the mechanochemical method. And the crucial factor which affects on battery performance was also examined.