• Journal of the Korean Solar Energy Society
• /
• v.30 no.4
• /
• pp.9-14
• /
• 2010

The main cause of global warming is carbon dioxide generated from the use of fossil fuels, and active research on the reduction of carbon is in progress to slow down the increasing global warming. Wind turbines generate electricity from kinetic energy of wind and are considered as representative for an energy source that helps to reduce carbon emission. Since the kinetic energy of wind is proportional to the cube of the wind speed, the intensity of wind affects wind farm construction validity the most. Therefore, to organize a wind farm, validity analysis should be conducted first through measurement of the wind resources. To facilitate the approval and permission and reduce installation cost, measuring sensors should be installed at locations below the actual wind turbine hub. Wind conditions change in shape with air density, and air density is most affected by the variable sterrain and surface type. So the magnitude of wind speed depends on the ground altitude. If wind conditions are measured at a location below the wind turbine hub, the wind speed has to be extrapolated to the hub height. This correction of wind speed according to height is done with the Deacon equation used in the statistical analysis of previously observed data. In this study, the optimal Deacon equation parameter was obtained through the analysis of the correction of the wind speed error with the Deacon equation based on the characteristics of terrain.

• Journal of the Korean Institute of Rural Architecture
• /
• v.8 no.1
• /
• pp.33-42
• /
• 2006

The rice mill occurred from modernization process of the farming village. It comes to follow in intention of the architect and is not the position building. By the user of the building it comes to follow necessary and it is a position thing. The like this rice mill was the community center of the village. Also the material which is unique and form quality were land mark of the village. The object of research is the rice mill where it takes charge of a like this role. And the scope of research is 8 rice mills of Eomjeong Myeon Chungju City which is located in the northern Chungbuk area. The progress of research the documentary survey, actual measurement, question, field work it analyzed the construction quality which the rice mill keeps with base and it arranges. The results of study are follows; 1. conditions of location : The rice mill the entrance of the village, the crossroads system is formed most the place is doing in the place which well. 2. The inside composition of a space : In order to compose the work space and the store space efficiently the plane surface is doing a rectangular form. 3. Form of roof : The roof raises the efficient characteristic of the work where is not the design which is intended to be naturally formed from the space composition for. 4. Selection of material : Most it was a natural enemy and an utility, it selected the scientific material and it used.

• Progress in Medical Physics
• /
• v.28 no.1
• /
• pp.33-38
• /
• 2017

Creating individualized build-up material for superficial photon beam radiation therapy at irregular surface is complex with rice or commonly used flat shape bolus. In this study, we implemented a workflow using 3D printed patient specific bolus and describe our clinical experience. To provide better fitted build-up to irregular surface, the 3D printing technique was used. The PolyLactic Acid (PLA) which processed with nontoxic plant component was used for 3D printer filament material for clinical usage. The 3D printed bolus was designed using virtual bolus structure delineated on patient CT images. Dose distributions were generated from treatment plan for bolus assigned uniform relative electron density and bolus using relative electron density from CT image and compared to evaluate the inhomogeneity effect of bolus material. Pretreatment QA is performed to verify the relative electron density applied to bolus structure by gamma analysis. As an in-vivo dosimetry, Optically Stimulated Luminescent Dosimeters (OSLD) are used to measure the skin dose. The plan comparison result shows that discrepancies between the virtual bolus plan and printed bolus plan are negligible. (0.3% maximum dose difference and 0.2% mean dose difference). The dose distribution is evaluated with gamma method (2%, 2 mm) at the center of GTV and the passing rate was 99.6%. The OSLD measurement shows 0.3% to 2.1% higher than expected dose at patient treatment lesion. In this study, we treated Mycosis fungoides patient with patient specific bolus using 3D printing technique. The accuracy of treatment plan was verified by pretreatment QA and in-vivo dosimetry. The QA results and 4 month follow up result shows the radiation treatment using 3D printing bolus is feasible to treat irregular patient skin.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.655-666
• /
• 2013

A number of highway projects are in progress in Korea to accommodate increasing transportation demands. As the highway route becomes more complex, some projects include tunneling through unconsolidated sedimentary rock. Since an unconsolidated sedimentary rock mainly consists of rock and ground mass, the behavior and characteristics in unconsolidated sedimentary rock tunnel are quite different from typical rock tunnel. However, construction case histories and rock classifications method on unconsolidated sedimentary rock tunnel had not been developed or studied domestically. Consequently the case studies and rock classification system for unconsolidated sedimentary rock are required to better understand its behavior for tunneling. In this study, rock mass classification method is proposed to identify unconsolidated sedimentary rock based on point load and slake durability tests. Based on this, the proposed method of unconsolidated sedimentary rock can be applied well through comparisons with the results of convergence measurement.

• Korean Journal of Construction Engineering and Management
• /
• v.10 no.3
• /
• pp.111-121
• /
• 2009

Value Engineering(VE) at design phase(so-called Design-VE) becomes quite a compulsory solution for better customer satisfaction, cost reduction, higher product performance, and, eventually, insured predominance in the competition. Unlike intended, however, the customer requirement on Design-VE has not been fully reflected in reality. Furthermore, the Design-VE occasionally does not progress in regular sequence; Preparation for measuring customer requirement - Function analysis - Idea creation. Therefore, this study suggests Axiomatic Design Theory to be adopted in Design-VE process expecting that the functions required by the customer could systematically reflected in VE process. Post-occupancy Evaluation(POE) is also represented as a method to measure and arrange the customer requirements. The customer satisfaction Design-VE process creates ideas defining functions in more detailed, to reflect the concrete user requirement. This approach helps function analysis and idea creation linked closely because function and idea are developed zigzag (i.e. function - idea - function...) in being decomposed into level down. The application of the process proposed by this study will be helpful to improve the customer requirement measurement and clarify a link between functions and ideas.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.214-219
• /
• 2011

Today, various activities to save energy are being conducted around the world. Even in our country, carbon reduction policy is being conducted for low carbon green growth and with this movement, effort to replace energy sources by recognizing the problems on environment pollution and resource exhaustion due to the indiscrete usage of fossil fuel is being made. Therefore, active study on renewable energy is in progress as part of effort to replace the energy supply through fossil fuel and solar ray industry has rapidly developed receiving big strength of renewable energy policies. The conclusion of this study measuring the surface temperature change of single crystal and polycrystalline PV module in green roof system and non-green roof system aspect are as follows. There was approximately $4^{\circ}C$ difference in PV module temperature in green roof system and non-green roof system aspect and this has the characteristic to decrease 0.5% when the temperature rises by $1^{\circ}C$ when the front side of the module is $20^{\circ}C$ higher than the surrounding air temperature following the characteristic of solar cells. It can be concluded that PV efficiency will be come better when it is $4^{\circ}C$ lower. Also, in result of temperature measurement of the module back side, there was $5^{\circ}C$ difference of PV module installed on the PV module back side and green roof system side on the 5th, $3^{\circ}C$ on the 4th, $2^{\circ}C$ on the 5th to show decreasing temperature difference as the air temperature dropped, but is judged that there will be higher temperature difference due to the evapotranspiration latent heat effect of green roof system floor side as the temperature rises. Based on this data, it is intended to be used as basic reference to maximize efficiency by applying green roof system and PV system when building non-green roof system flat roof.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.7
• /
• pp.5-14
• /
• 2020

Kansai International Airport (KIX) was opened in September 1994. Although 26 years have passed since the completion of the first island, long-term settlement is still in progress. This settlement occurs in the Pleistocene layer. For it is not easy to determine the permeability of the Pleistocene sand layer because the thickness and the degree of fine content in the horizontal direction are constantly changing. In addition, it is also a difficult to predict the interactive behavior of the ground due to the construction of the second phase island adjacent to it. In order to solve this problem, a two-dimensional finite element analysis considering elasto-viscoplastic was performed to evaluate the long-term deformation, including the interactive behavior of the alternating Pleistocene foundation due to the construction of two adjacent reclaimed islands. In general, two-dimensional analysis can be used when a section can represent the entire sections. However, Kansai Airport is an artificial reclaimed island so two-dimensional analysis cannot solve the problem such as the stress deformation in the corners of the island. Additionally, the structure of the actual sub-ground through physical exploration is non-homogeneity and its thickness is also not constant. Therefore, there are limitations for the two-dimensional analysis to explain the phenomena. That is, three-dimensional analysis is strongly required. Due to these demands, the author extended the existing two-dimensional program capable of elasto-viscoplastic analysis to three-dimensional and completed the verification of the three-dimensional program developed through one-dimensional consolidation analysis. In order to demonstrate the validity of the developed 3D program that has been verified, an analysis is performed under the same analysis conditions as the existing research using a two-dimensional program. The effectiveness of the developed 3D numerical analysis program was demonstrated by comparing the analysis results with the 2D results and actual measurement data.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.864-867
• /
• 2003

GPS (Global Positioning System) made by the Department of Defense in U.S.A is positioning system to use satellite and initially it has been used only for the military forces but open to civilian in about 1987. This system has widely been used for not only surveying land, but also car navigation on the street and means to build up the data of the GIS. With GPS, recently our country is accelerating to make imbeded system and also the study on imbeded system is well under way. For example, Car navigation and the construction of the Seokang bridge between Willson Arch at Han river by using DGPS were evaluated as successful model to lead accurate location with the precision of the cm. The examples of the project performance with GPS has gradually been extended to the each department organization of the local and central government. for the example, It is true that BIS(Bus Information System) is widely spreading out. In addition, the study on the Distribution Maintenance System is expected to be well in progress to take advantage of GPS based on the data base of the NGIS(National Geography Institute System) of the NGI(National Geography Institute). This paper shows that we embodied not only the large imbeded system for car and finding the location in Korean Land Corporation but also the protype of the kinematics Wrist Held which is easily portable to pedestrian, climber and marathon runner.

• Spatial Information Research
• /
• v.23 no.5
• /
• pp.41-52
• /
• 2015

MOLIT (Minister of Land, Infrastructure and Transport) authorized Indoor Spatial Information as Basic spatial information in 2013. It became a legal evidence for constructing and managing Indoor Spatial Information. Although it has a little advantage to utilize as service level that Indoor Spatial Information by laser scan or measurement, it has a lot of problems such as consuming many resources, requiring additional progresses for inputting Object Information. In conclusion, it is inefficient to utilize for the maintenance and domestic AEC/FM field. The purposes of this study is to output Indoor Spatial Information by operating IFC model which based on open BIM and to improve availability of Indoor Spatial Information with data visualization. The open-sources of IFC Exporter, a inner program of Revit (Autodesk Inc), is used to output Indoor Spatial Information. Directs 3D Library is also operated to visualize Indoor Spatial Information. It is possible to inter-operate between XML format and the objects of Indoor Spatial Information. It can be utilized in various field as well. For example COBie linkage in facility management, construction of geo-database using air-photogrammetry of UAV (Unmaned Areal Vehicle), the simulation of large-scale military operations and the simulation of large-scale evacuation. The method that is purposed in this study has outstanding advantages such as conformance with national spatial information policy, high level of interoperability as indoor spatial information objects based on IFC, convenience of editing information, light level of data and simplifying progress of producing information.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.699-711
• /
• 2011

This study is to perform several major analyses to find any differences in the leverage between the pre- and post-period of the currency crisis. Moreover, another aspect is to investigate a financial aspect which has received relatively little attention to the firms and/or industries in the emerging capital markets in comparison to those in the advanced markets. The purpose of this empirical study is to confirm whether or not, it is myth or reality that Korean business conglomerate, chaebol, firms with subsidized financing from government-owned domestic financial institutions in the pre-financial turmoil, may still maintain their higher leverage, even after the crisis. It was found that firms belonging to the chaebol in Korea maintained higher average book-value and market-value based debt ratios, relative to their counterparts not belonging to the chaebol across all of the tested models. There were positive relationships of IND3(=the chemical industry) and Ind5(=the construction industry) to the book-value leverage. This study identified that there were no differences in the explanatory variables included, between the tested models (that is, without and with including the present value of an operating lease) related to each debt ratio. Since the Korean government continue to improve the corporate governance of the domestic firms in terms of accounting transparency and corporate ownership, it would be more efficient, if utilizing this "new" ratio considering an operating lease as an effective measurement of the level of leverage. In terms of the capital structure, it may also be possible for foreign firms to utilize and benefit from the results obtained in this study when operating their new businesses in Korea, given the economic circumstances such as the ongoing progress of the Korea-America FTA or the Korea-China FTA.