• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.335-335
• /
• 2008

Phosphate glass samples with various $Cr_2O_3$ and $Er_2O_3$ contents based upon $55P_2O_5\cdot24BaO\cdot10K_2O\cdot4Al_2O_3\cdot6Yb_2O_3$ were prepared. The prepared glass compositions are dehydrated using gas bubble flow method in open system and investigated the effects of the eliminating of OH groups from the glass melts with bubbling time. It was found that the probability of $Er^{+3}$ fluorescence quenching by OH groups oscillations linear depends upon the OH groups absorption coefficients in the maximum of the stretch vibrations band at $3500cm^{-1}$ while $Er^{+3}$ concentration range is between $1.6\times10^{19}$ and $21.2\times10^{19}$ ion/$cm^3$.

• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.231-238
• /
• 2020

The composition of martensite transformation in NiAl alloy is determined using pure nickel and aluminum powder by vacuum hot press powder metallurgy, which is a composition of martensitic transformation, and the characteristics of martensitic transformation and microstructure of sintered NiAl alloys are investigated. The produced sintered alloys are presintered and hot pressed in vacuum; after homogenizing heat treatment at 1,273 K for 86.4 ks, they are water-cooled to produce NiAl sintered alloys having relative density of 99 % or more. As a result of observations of the microstructure of the sintered NiAl alloy specimens quenched in ice water after homogenization treatment at 1,273 K, it is found that specimens of all compositions consisted of two phases and voids. In addition, it is found that martensite transformation did not occur because surface fluctuation shapes did not appear inside the crystal grains with quenching at 1,273 K. As a result of examining the relationship between the density and composition after martensitic transformation of the sintered alloys, the density after transformation is found to have increased by about 1 % compared to before the transformation. As a result of examining the relationship between the hardness (Hv) at room temperature and the composition of the matrix phase and the martensite phase, the hardness of the martensite phase is found to be smaller than that of the matrix phase. As a result of examining the relationship between the temperature at which the shape recovery is completed by heating and the composition, the shape recovery temperature is found to decrease almost linearly as the Al concentration increases, and the gradient is about -160 K/at% Al. After quenching the sintered NiAl alloys of the 37 at%Al into martensite, specimens fractured by three-point bending at room temperature are observed by SEM and, as a result, some grain boundary fractures are observed on the fracture surface, and mainly intergranular cleavage fractures.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.4
• /
• pp.223-229
• /
• 2004

The effects of the cooling and annealing conditions on the microstructures and corrosion properties were investigated for the Cu-contained Zr-Nb alloy (Zr-1.1Nb-0.07Cu). After annealing at $1050^{\circ}C$ for 15 min, the specimens were cooled by three methods of water quenching, air cooling, and furnace cooling. Widmanstatten structures were developed in both air- and furnace-cooled specimens, and the Widmanstatten plate width of the furnace-cooled specimens was wider than that of the air-cooled ones. The weight gain in the furnace-cooling case was higher than that in the air-cooling case. This could be the reason why the diffusion time was more enough during the furnace cooling than the air cooling. The oxide of the furnace-cooled specimen was nonunformly formed just beneath the Widmanstatten plate boundaries, where ${\beta}_{Zr}$ phases were exised concentrately. Compared with the $640^{\circ}C$ annealing after the water quenching, the $570^{\circ}C$ annealing could make the ${\beta}_{Nb}$ phases and a concomitant reduction of the Nb in the matrix, and then it could improve the corrosion resistance with the increase of the annealing time. It would be concluded that the corrosion resistance of the Zr-1.1Nb-0.07Cu was good when the Nb concentration in the matrix was reached at an equilibrium level and then the ${\beta}_{Nb}$ phase was formed.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.5
• /
• pp.288-296
• /
• 2005

The corrosion behaviors of Zr-based alloys were very sensitive to their microstructures which were determined by manufacturing process. The specimens of Zr-based alloy named as HANA-4 for nuclear fuel cladding were investigated in order to get the optimized manufacturing process such as the intermediate annealing temperature and cold working steps after the ${\beta}$ quenching. From the microstructural analysis, cold worked microstructure of the samples was changed to the recrystallized microstructure by performed process. The corrosion behaviors of HANA-4 alloy were affected by the different manufacturing process. The ${\beta}$-Zr phase was formed in the matrix and the Nb concentration in the ${\beta}$-Zr phase was increased as progressing the manufacturing process. So, it was found that the corrosion rate of HANA-4 alloy was affected by the Nb concentration in the matrix.

• Journal of the Korean Ceramic Society
• /
• v.55 no.5
• /
• pp.461-472
• /
• 2018

$Gd_2O_3:Eu/Bi$ nanoparticles were synthesized via spray pyrolysis and applied for the preparation of a luminescent pearl pigment as an anti-counterfeiting material. The luminescence properties were optimized by changing the $Eu^{3+}$ and $Bi^{3+}$ concentration. Ethylene glycol was used as an organic additive to prepare the $Gd_2O_3:Eu/Bi$ nanoparticles. The highest emission intensity was achieved when the total dopant content was 10.0 at.% and the mole fraction of Bi was 0.1. The concentration quenching was mainly due to dipole-dipole interactions between the same activators, and the critical distances were 9.0 and $19.6{\AA}$ for $Eu^{3+}$ and $Bi^{3+}$, respectively. The prepared $Gd_2O_3:Eu/Bi$ powder exhibited an average size of approximately 82.5 nm and a narrow size distribution. Finally, the $Gd_2O_3:Eu/Bi$ nanophosphor coated on the surface of the pearl pigment was confirmed to have good red emission under irradiation from a portable ultraviolet light-emitting diode lamp (365 nm).

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.41-41
• /
• 2011

The aims of this study were to examine the efficacy of phytochemicals of Rumex crispus as anti-oxidant and anti-browning agent. The bioactive properties of Rumex crispus as natural colorants were studied by total phenolic contents, DPPH radical scavenging, ABTS radical scavenging,lipid peroxidation, cell viability, singlet oxygen quenching and photoprotection effect. Among all of the results ($IC_{50}$: the concentration of various extracts required to exert 50% reducing effect), the higher activity of the extract was found in the ethyl acetate and butanol extracts. Anti-browning activity was evaluated by monitoring the change $L^*$, $a^*$, $b^*$ values and total color differences(${\Delta}E$). It was found that ethyl acetate and butanol extracts effectively inhibited browning in apple juice at a concentration below 0.3 mg/ml. Rumex crispus extracts used natural colorants could be of good resources as anti-oxidant and anti-browning agents. The results suggest that our study may contribute to the development of natural and functional materials with potential application to reduce oxidative damage.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1031-1037
• /
• 1998

To investigate the effect of cooling rate and annealing temperature on the corrosion of Zircaloy-4 and Zr-2. 5Nb alloys, autoclave corrosion tests were performed at $500^{\circ}C$ for the specimens prepared by various heat treatments. The specimens were heat-treated at $1050^{\circ}C$ for 30 minutes and cooled by ice-brine quenching, water quenching, oil quenching, air cooling, and furnace cooling. To investigate the effect of annealing temperature, the specimens were annealed at $\alpha$, ($\alpha$+$\beta$)-, and $\beta$-temperatures. It was observed from the $500^{\circ}C$ corrosion test that nodular corrosion occurred on the Zircaloy-4 alloy but did not occur on the Zr-2.5Nb alloy. The corrosion resistance of Zircaloy-4 increased with increasing the cooling rate. On the other hand, the corrosion resistance of Zr-2.5Nb decreased with increasing the cooling rate and the annealing temperature. It is suggested that corrosion resistance of Zircaloy-4 would be controlled by the distribution of Fe and Cr element in the matrix and precipitates, while that of Zr-2.5Nb alloy the niobium concentration and $\beta_{-Nb}$ phase.

• Applied Biological Chemistry
• /
• v.45 no.2
• /
• pp.53-58
• /
• 2002

Quinacrine, a pH-sensitive fluorescence probe, which exists either as an unprotonated fluorescence form or a protonated noufluorescence form, can be used to measure the proton transport activity of $H^+-ATPase$. Quinacrine was used to determine the optimal conditions for measuring the activity of microsomal $H^+-ATPase$ prepared from the roots of tomato plants. The amount of quinacrine fluorescence quenching obtained at $0.43{\mu}g/{\mu}l$ of microsomal protein concentration was 25-26%, which shows that the enzyme activity of 100 nmol/min decreases 10% of quinacrine fluorescence. Maximal fluorescence quenching was obtained at pH 7.0-7.2 and 2 mM $Mg^{2+}$ Because the activity of microsomal $H^+-ATPase$ is also maximal at these conditions, the quinacrine fluorescence well represents the activity of $H^+-ATPase$. Vanadate and $NO_3-$, specific inhibitors of plasma and vacuolar $H^+-ATPases$, respectively, were successfully applied to inhibit the quinacrine fluorescence quenching mediated by the corresponding $H^+-ATPases$. These results imply that quinacrine is a useful tool for measuring the proton transport activities of microsomes obtained from the root tissue of tomato plants.

• Journal of the Korean Ceramic Society
• /
• v.49 no.4
• /
• pp.325-327
• /
• 2012

Europium-doped $LaSi_3N_5$ phosphor was synthesized from LaSi/Si/$Si_3N_4/Eu_2O_3$ mixture by nitridation at $1390^{\circ}C$ and additional annealing at $1650^{\circ}C$ for 4 h. The phosphor shows emissions in the green light region with a maximum at 560 nm. With increasing europium content in the general formula $La_{1-z}Eu_zSi_3N_{5-z}O_{1.5z}$ from z = 0.01 to 0.06 there was a maximum emission for z = 0.04 followed by concentration quenching for the highest europium content (z = 0.06).

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.166-166
• /
• 2006

The photoluminescence (PL) efficiency of $Ir(ppy)_{3}$:PVK is lower than $Ir(ppy)_{3}$:CBP for the whole range of doping concentration and this low PL efficiency can be a reason of the lower efficiency of PhPLED than PhOLED. The lower efficiency is originated from the large bi-excitonic quenching such as the triplet-triplet annihilation. The PhPLEDs showed very short lifetime. The short lifetime was found to be originated from the instability of the doubly reduced $Ir(ppy)_{3^{-2}}$. The double reduction takes place because of the low electron mobility of PVK and large energy difference of LUMO level between PVK and $Ir(ppy)_{3}$.