• 한국가구학회지
• /
• 제11권1호
• /
• pp.85-89
• /
• 2000

This study investigated the effect of steaming on fixation of compression set and the effect of these treatments on mechanical properties of heat-compressed wood specimens. To determine the effect of steaming after compression set, wood specimens were compressed for 100min at 180f and then steamed for 20-100min at $120^{\circ}C$. Swelling tests were used to evaluate recovery of compression set. Bending, compression, and Brinell hardness tests were carried out for evaluating mechanical properties. Compressed wood steamed for 100 min at $120^{\circ}C$ showed 1.9% recovery of set, increases in bending and compressive properties, and no hardness change. We concluded that almost complete fixation of compression set in wood can be achieved by steaming compressed wood.

• Elastomers and Composites
• /
• 제44권1호
• /
• pp.41-46
• /
• 2009

천연고무의 일정하중 영구압축률에 온도와 가교시스템이 미치는 영향을 고찰하였다. 다양한 가교시스템과 가교밀도의 고무시편을 만들기 위해 여러 가지 함량의 황과 dicumyl peroxide(DCP)를 사용하여 배합하였으며, 가교된 천연고무의 일정변위 조건에서 측정된 영구압축률과 일정하중에서 측정된 영구압축률의 차이를 비교하였다. 일정하중 영구압축률은 일정변위 영구압축률에 비해 가교밀도의 변화에 따라 상대적으로 큰 차이를 보였으며, 이는 영구압축률 측정 시 공급된 변형에너지가 다르기 때문이다. 또한 일정하중 영구압축률 측정에서 황으로 가교시킨 시편의 경우 하중과 온도증가에 따라 영구압축률이 크게 증가하였고, 이에 반해 DCP로 가교시킨 시편의 경우 하중과 온도증가에 큰 영향을 받지 않았다.

• Journal of the Korean Wood Science and Technology
• /
• 제39권4호
• /
• pp.311-317
• /
• 2011

라디에타 소나무(Pinus radiata D.Don)를 압체온도 $180^{\circ}C$, 압체시간 60분 조건으로 열압밀화 목재를 제작하여 압축세트량에 따른 종압축강도, 휨강도, 경도, 못뽑기저항을 조사하였다. 압축세트량 60%인 열압밀화 목재의 비중은 1.01로 나타났으며, 대조군의 비중 0.48에 비해 현저히 증가한 값을 나타내었다. 압축세트량의 증가와 함께 모든 역학적 특성도 향상되었다. 그리고 라디에타 소나무의 최대 압축세트량은 약 65%로 확인되었으며, 이는 비중 0.48인 라디에타 소나무의 공극율 68%와 거의 일치하는 결과이다.

• 한국가구학회지
• /
• 제23권4호
• /
• pp.460-466
• /
• 2012

This study was conducted to investigate the surface hardness of thermally-compressed larch wood by compression set and temperature. The surface hardness of thermally-compressed larch wood increased with increasing compression set and temperature. For compression set 60%, the specific gravity was increased as 0.93. However, the surface hardness was lower value as 31.1 N/$mm^2$ compared with a similar specific gravity of the tropical timber. For density profile, less than compression set 40%, compression was observed mainly surface area. On the other hand, more than 50%, density profile variation was reduced by compression of central part. Results of this study indicate that thermally-compressed larch wood can be replace some imported hardwoods such as oak or cherry. However, thermally-compressed larch wood was difficult to replace the tropical timber being imported in terms of surface hardness.

• Elastomers and Composites
• /
• 제53권4호
• /
• pp.220-225
• /
• 2018

Resilient pads play a major role in reducing the impact of loads on a rail in a rail-fastening system, which is essentially used for a concrete track. Although a compression set test is commonly used to measure the durability of a resilient pad, the static spring constant is often observed to be different from the fatigue test. In this study, a modified compression set test method was proposed to monitor the variations in the compression set and static spring constant of a resilient pad with respect to temperature and time. In addition, the life of the resilient pad was predicted by performing an acceleration test based on the Arrhenius equation.

• 한국응급구조학회지
• /
• 제14권3호
• /
• pp.71-81
• /
• 2010

Purpose: To minimize an interruption in chest compression, reduce the hands-off time, the American Heart Association has recommended the ratio of chest compression to ventilation ratio to 30:2 from 2005 CPR guideline to 2010 CPR guideline. However, current studies have shown that the hands-off time was > 10 seconds with that method. For this reason, we devised new CPR method that a ventilation to chest compression ratio of 2:30 to reduce pt assessment time and skipped the assessment step of carotid artery pulse would be a more effective way to reduce the hands-off time & the time to set the CPR. According to the more detailed purpose are listed below. 1) We would like to confirm efficiency of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 to reduce the hands-off time & the time to set the CPR. 2) We would like to evaluate possibility of increasing for chest compression accuracy of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 3) We would like to evaluate possibility of increasing for ventilation accuracy of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 Methods: According to 2005 American Heart Association Guidelines, 60 paramedic students(20 students X freshmen, sophomore, junior) performed 5 cycles of 3~ chest compressions : 2 ventilations after A, B, C evaluation with Laerdal Resusci R Anne SkillReporters. After 5 minutes rest, the 60 students performed 5 cycles of 2 ventilations : 30 chest compressions after A, B evaluation with the manikins between 13 and 17 September 2010. The short reports including speed & accuracy of chest compression, respiratory, CPR cycle were gained from the manikins. Hands-off times were measured by assistants. Results: Recently, the importance of high quality CPR was emphasized in order to perform the CPR faster and more accurate. To find out improving the conventional CPR method, we switch the procedure of the compression and the ventilation. By switching the procedure back and forth, we are able to compare the effectiveness of CPR between two type of CPR method which are 2:30 and 30:2 methods. 2:30 is that the breaths is delivered twice, first and perform 30 compressions while 30:2 perform 30 compressions first and give 2 breaths followed by the ABC method. Also, we verify the effectiveness of the hands off time, compression accuracy of the compression through the comparison of the two procedure as mentioned earlier. Consequently research verified that 2:30 is the efficient by providing faster set up delivering more accurate chest compression. Conclusion: 2:30 can minimize a time delay from cardiac standstill until starting the chest compression. In addition, hands-off time which is an interruption in chest compression can be shortened by 2:30 method, which result to effective oxygenation of coronary artery & maintenance of the bloodstream. Once again, performing the 2:30 method provide lessen hands off time and increase the accuracy of the chest compression.

• Elastomers and Composites
• /
• 제35권2호
• /
• pp.106-114
• /
• 2000

상온에서의 충격 흡수특성과 compression set 특성을 향상시키기 위하여 ethylene vinyl acetate copolymer (EVA)와 styrene vinyl isoprene styrene triblock copolymer (SVIS)를 블렌드하여 발포체를 제조하였다. 발포제 및 EVA/SVIS 블렌드비가 발포배율 및 기계적 물성에 미치는 영향을 조사하였다. SVIS 함량이 증가함에 따라 블렌드의 점도는 증가하였고 가교 속도는 감소하였으며, 발포배율은 감소하여 비중은 증가하였다. 발포제 함량 증가, 즉 발포배율 증가에 따른 반발탄성은 변화가 없는 반면에, SVIS 함량 증가에 따라 발포체의 상온에서의 tan ${\delta}$ 값은 증가하였으며 따라서 반발 탄성은 감소함을 알 수 있었다. EVA/SVIS 블렌드 발포체에서 SVIS 함량 증가에 따라 가교밀도와 비중이 증가하므로 compression set 값도 낮은 값을 나타내었다.

• 대한수학회지
• /
• 제38권3호
• /
• pp.669-681
• /
• 2001

This paper introduces the notions of essential and inessential map for countably $textsc{k}$-set contractive maps. These ideas enable us to establish a Krasnoselskii-Petryshyn compression and expansion theorem in a cone for countably $textsc{k}$-set contractive maps.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.918-927
• /
• 2018

Based on the actual operating environment of transformer, the aging tests of nitrile butadiene rubber (NBR) were conducted systematically under four conditions: in air, in transform oil, under compression in air and under compression in transform oil to studythe effect of high temperature, transform oil and compression stress simultaneously on the thermal aging behaviors of nitrile butadiene rubber and predict the lifetime. The effects of liquid media and compression stress simultaneously on the thermal aging behaviors of nitrile butadiene rubber were studied by using characterization methods such as IR spectrosc-opy, thermogravimetric measurements, Differential Scanning Calorimetry (DSC) measurements and mechanical property measurements. The changes in physical properties during the aging process were analyzed and compared. Different aging conditions yielded materials with different properties. Aging at $70^{\circ}C$ under compression stress in oil, the change in elongation at break was lower than that aging in oil, but larger than that aging under compression in air. The compression set or elongation at break as evaluation indexes, 50% as critical value, the lifetime of NBR at $25^{\circ}C$ was predicted and compared. When aging under compression in oil, the prediction lifetime was lower than in air and under compression in air, and in oil. It was clear that when predicting the service lifetime of NBR in oil sealing application, compression and media liquid should be involved simultaneously. Under compression in oil, compression set as the evaluation index, the prediction lifetime of NBR was shorter than that of elongation at break as the evaluation index. For the life prediction of NBR, we should take into account of the performance trends of NBR under actual operating conditions to select the appropriate evaluation index.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.444-449
• /
• 2001

The purpose of the work is to improve comfort of a car seat, especially dynamic comfort which affects driver's discomfort during the long time driving. Definition of dynamic comfort was made before the investigation of which parameter affects seat comfort. In order to optimize design parameters so as to maximize seat comfort as well as to know the cause of discomfort, benchmarking on a target vehicle and competitive vehicles was performed, which showed both the vibration transmission characteristics and the compression set due to dynamic loading should be reduced. As a solution ball rebounds was increased by about 10％ of the original foam, which showed reduction of S.E.A.T. value by 10％ and of compression set by 60％.