• 한국표면공학회지
• /
• 제39권1호
• /
• pp.1-8
• /
• 2006

In this study, effect of sputtering after plasma nitriding and before PVD coating on the microstucture, microhardness, surface roughness and the adhesion strength of CrN thin films were investigated. Experimental results showed that this sputtering process not only removed surface compound layer which formed during a plasma nitriding process but also induced an alteration of the surface of plasma nitrided substrate in terms of microhardness distribution and surface roughness, which in turn affected the adhesion strength of PVD coatings. After sputtering, microhardness distribution showed general decrease and the surface roughness became increased slightly. The critical shear stress measured from the scratch test on the CrN coatings showed an approximately twice increase in the binding strength through the sputtering prior to the coating and this could be attributed to a complete removal of compound layer from the plasma nitrided surface and to an increase in the surface roughness after sputtering.

• 소성∙가공
• /
• 제14권3호
• /
• pp.263-268
• /
• 2005

Heating channel layout design and evaluation technology for SMC molding system was investigated in this work. Traditional rules of cooling channel design in injection molding were applied to the present work. Finite element thermal analysis with $ANSYS^{TM}$ was performed to evaluate the temperature distribution of SHC mold surface. SMC mold was manufactured to evaluate the effect of a proposed heating channel layout system on the temperature distribution of SMC mold surface and infrared camera was applied to a measurement of temperature distribution. It was shown that infrared camera application was possible in a measurement of temperature distribution on SHC mold surface.

• 한국주조공학회지
• /
• 제10권5호
• /
• pp.392-398
• /
• 1990

To improve free-cutting property, fine Pb, Bi particles is necessary to be distributed evenly in Al-Cu alloy. The control of added element size and distribution are very difficult because of the physical properties of Pb, Bi. The effect of master alloy compositions on microstructure and particle distribution was investigated. The ribbon shape of Pb-50wt% Bi master alloy showed the best results. And Ti addition improved even distribution of Pb, Bi particles. Particles grown from $L_2$ phase were considered to be the Pb, Bi compound.

• Journal of Forest and Environmental Science
• /
• 제40권2호
• /
• pp.123-140
• /
• 2024

More than half of the global distribution of the Rhododendron genus is found in China, with over 74% being endemic species. However, there is still insufficient data to chemically classify the Rhododendron genus native to China. Therefore, in this study, a chemotaxonomic study was conducted to determine the presence of taxifolin-3-O-arabinopyranoside, a flavonoid compound, in the Rhododendron genus native to China. Forty-three species of Rhododendron native to China-20 from across China, 8 from Beijing, 6 from Yanbian, and 9 from Yunnan-were utilized in the experiment. Through HPLC analysis, the retention time was compared with that of taxifolin-3-O-arabinopyranoside, a standard compound, and quantitative analysis was conducted. As a result, taxifolin-3-O-arabinopyranoside was detected in 22 out of 43 the Chinese Rhododendron species. Afterwards, LC-MS/MS analysis was performed on the 22 species in which taxifolin-3-O-arabinopyranoside was detected to determine whether the molecular weight was consistent with the standard compound. Under negative conditions, it was confirmed that all samples exhibited the same molecular weight as taxifolin-3-O-arabinopyranoside, 435-436 m/z. The same compound was detected in more than half of the Rhododendron species used in the experiment, and taxifolin-3-O-arabinopyranoside was determined to be an indicator compound for Rhododendron species native to China. In addition, the possibility of using the above results as basic data for chemical classification of Chinese Rhododendron genus was confirmed.

• 복식
• /
• 제59권6호
• /
• pp.118-125
• /
• 2009

Goryeong Jeesandong tombs No.73 from the 5th century located in Gyeongsangbookdo is the most representative remains of the Daegaya. They were excavated and examined by the Daedong Research Center for Cultural Properties. In this study, the textiles in the Goryeong Jeesandong tomb No.73 is identified and their features are examined through scientific analysis. Due to the fact that the remains were not treated for preservation, we were able to observe many samples under the microscope. Within the hemp textiles both hemp and ramie were made using s-twist threads and the thread count distribution is calculated to be 8.0${\sim}$20.0/$cm^2$. Among the silk, the taffeta was categorized into five types. First, there was plain woven silk which the thickness of the warp and the weft is the same and their rate of threadcount was the same. The second type was thin tabby which is spacious between threads. The third kind was woven by warp and weft which had very different thickness. The fourth type used two threads for each warp. The fifth kind used two threads for the warp threads and used thick threads for the weft for a modified plain weave, and it is the first of its kind to be found. Also, there was a compound weave with warp-faced compound weave among silk.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.534-538
• /
• 2002

Dissimilar friction stir welding of aluminum (AI) alloy 1050 and magnesium (Mg) alloy AZ31 was successfully done in the limited welding parameters. The dissimilar weld showed good quality and facility compared to conventional fusion weld. Transverse cross section perpendicular to the welding direction had no defects. The weld was divided into base material of Al alloy, an irregular shaped stir zone and base material of Mg alloy. The irregular shaped stir zone was roughly located around the initial weld center. The weld interface near plate surface shifted from initial weld centerline to the advancing side. Hardness profile of the weld was heterogeneous, and the hardness value of the stir zone was raised to about 150 Hv to 250 Hv. The mixed phase was identified to intermetallic compound $Mg_{17}$Al$_{12}$ using x-ray diffraction method, energy dispersive x-ray spectroscopy (EDX) and electron probe micro analysis (EPMA). The formation of intermetallic compound $Mg_{17}$Al$_{12}$ during FSW causes the remarkable increase in hardness value in the stir zone.one.

• Mass Spectrometry Letters
• /
• 제9권2호
• /
• pp.61-65
• /
• 2018

KPLA-012, a benzopyranyl 1,2,3-triazole compound, is considered a potent $HIF-1{\alpha}$ inhibitor based on the chemical library screening, and is known to exhibit anti-angiogenetic and anti-tumor progressive effects. The aim of this study was to investigate the pharmacokinetic properties of KPLA-012 in ICR mice and to investigate in vitro characteristics including the intestinal absorption, distribution, metabolism, and excretion of KPLA-012. The oral bioavailability of KPLA-012 was 33.3% in mice. The pharmacokinetics of KPLA-012 changed in a metabolism-dependent manner, which was evident by the low recovery of parent KPLA-012 from urine and feces and metabolic instability in the liver microsomes. However, KPLA-012 exhibited moderate permeability in Caco-2 cells ($3.1{\times}10^{-6}cm/s$) and the metabolic stability increased in humans compared to that in mice (% remaining after 1 h; 47.4% in humans vs 14.8% in mice). Overall, the results suggest that KPLA-012 might have more effective pharmacokinetic properties in humans than in mice although further studies on its metabolism are necessary.

• Journal of the Optical Society of Korea
• /
• 제11권2호
• /
• pp.76-81
• /
• 2007

The compound refractive X-ray lens (CRL) for focusing hard X-rays is investigated to determine the parameters such as the focal length, the focal spot size, and spatial distribution at the focal spot using a simple theoretical calculations and CRLs fabricated by the self-assembly method. The number of individual compound lenses are defined for the given focal length of 1 m. The X-ray energy of 1 to 40 keV is used in the calculations. The CRL for focusing hard X-rays which generated from the X-ray tube is fabricated by nanoparticle-polymer composite in the form of circular concaves. The self-assembly method is applied to form the nanoaluminum-poly (methly meth-acrylate) composite and carbon-polymer composite CRL lenses. Aluminum nanoparticles of 100 nm and carbon microparticles are diffused in the polymer solution then the high gravity up to 6000G is applied in it to form the concave lens shape. X-ray energy at 8 keV is used for characterization of the composite CRLs. The FWHM of intensity for the fabricated nanoaluminium composite CRL system, N=10 is measured as 1.8 mm, which would give about $70{\mu}m$ in FWHM at 1 m of the focal length.

• Journal of the Korean Statistical Society
• /
• 제36권2호
• /
• pp.237-256
• /
• 2007

This paper studies the problem of option pricing in an incomplete market. The market incompleteness comes from the discontinuity of the underlying asset price process which is, in particular, assumed to be a compound Poisson process. To find a reasonable price for a European contingent claim, we first find the unique minimal martingale measure and get a price by taking an expectation of the payoff under this measure. To get a closed-form price, we use an asymptotic expansion. In case where the minimal martingale measure is a signed measure, we use a sequence of martingale measures (probability measures) that converges to the equivalent martingale measure in the limit to compute the price. Again, we get a closed form of asymptotic option price. It is the Black-Scholes price and a correction term, when the distribution of the return process has nonzero skewness up to the first order.

• 환경위생공학
• /
• 제10권3호
• /
• pp.78-84
• /
• 1995

Cationic surfactants can be used to modify surface of solids to promote adsorption of hydrophobic organic compounds. This behavior is due to the surfactant forming aggregate structure on the solid surface. Partition coefficients are commonly used to quantify the distribution of organic pollutants between the aqueous and particulate phases of aquatic system Partitioning of hydrophobic compounds to cetyltrimethylammonium bromide ( CTAB ) coated silicate has been investigated as a function of surfactant surface coverage at I=0 and 0.1 ionic strength. Toluene, Xylene, TCI sorption experiments demonstrated that the CTAB coated silicate was able to remove these hydrophobic organic compounds from solution The hydrophobic organic compound with the higher Kow had higher removals than lowest Kow hydrophobic organic compound.