• 한국안전학회지
• /
• 제21권4호
• /
• pp.49-54
• /
• 2006

The evaluation of elastic-plastic fracture characteristic was investigated in ferrite steel SA 516- Gr70 used for reactor coolant piping elbow and support skirt of pressure vessels. This paper describes the effect of temperature on J-R curve characteristic of this material. The elastic-plastic fracture mechanics parameter J is obtained with unloading compliance method. The test method were analyzed according to ASTM E 813-89 and E 1152-89. Unloading compliance $J_{IC}$ tests were performed on 1 CT specimens at varied temperatures from $25^{\circ}C$ to about $400^{\circ}C$ using a high temperature extensometer. At all temperature, valid $J_{IC}$ measurements could be made and $J_{IC}$ decreased with increasing temperature. SEM fractography schematically illustrates microvoid initiation, growth and coalescence at the tip of a preexisting crack.

• International Journal of Fluid Machinery and Systems
• /
• 제10권3호
• /
• pp.197-208
• /
• 2017

When Francis turbines operate at partial load, residual swirl in the draft tube causes low-frequency pulsation of pressure and power output. Scale effects and system response may bias the prediction of prototype behavior based on laboratory tests, but could be overcome by means of a 1D analytical model. This paper deals with the two most important features of such a model, the compliance and the source of excitation. In a distributed-parameter version, compliance should be represented as an exponential function of local pressure. Lack of similarity due to different Froude number can thus be compensated. The normally unknown gas content in the vortex cavity has significant influence on the pulsation, and should therefore be measured and considered as a test parameter.

• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.441-446
• /
• 2001

In this paper the effect of bump compliance, load, and the number of pad on the lift-off speed is studied. When the load is greater and bump compliance lower, the shaft is lifted off at higher rotating speed. And when the load is applied near the center of pad, lift-off speed is lower. When the number of pad increases, the lift-off speed is higher. The lift-off characteristics can be used to lengthen the lift time of the coating and design the rotating machinery supported by bump bearings.

• Journal of Welding and Joining
• /
• 제11권1호
• /
• pp.42-51
• /
• 1993

In this study, investigations were conducted in calculating parameters of elastic-plastic fracture mechanics using single specimen. The validity of these testing methods was judged by the confirmation of multiple specimen method of stop block test. The results were as follows: In order to measure a fracture toughness using the instrumented impact test, two general requirement must be considered; One, setting up proper impact velocity considered the effect of loading and the other, the necessity of low blow test for obtaining true energy by the compliance correction. It was possible to detect a crack initiation point by calculating the compliance changing rate from a load-defection curve. Criterion of a stable crack growth, $T_{mat}$ could be estimated by using key-curve method for a base metal. and combining Kaiser's rebound compliance with Paris-Hutchison's $T_{appl}$ equation for the brittled zone of welding heat affected.at affected.d.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.204-213
• /
• 2001

This paper develops the compliance approach to the problem of load sharing between a cracked plate and a cover plate used to bridge the crack. The theory is validated by using calculated stress intensity factors for the covered and uncovered cases and by using stop hole method to reduce experimentally observed growth rates to a common base. Calculations are then made on the effect of cover plate width on fatigue crack retardation in order to demonstrate the predictive capability of the technique.

• 한국해양공학회지
• /
• 제10권2호
• /
• pp.98-105
• /
• 1996

A method is proposed to evaluate the elastic-plastic fracture resistance curve only with load displacement records without the crack length measurement in CT specimen. This method is based on the idea that the effect of plastic deformation and the crack growth can be measured only by using a load-displacement record. If we know the reference-load curve representing the hardening of specimen, then the crack extension can be calculated by the elastic compliance determined from the load ratio. The results of this proposed method were compared to those of the elastic-plastic fracture resistance curve for the ASTM standard unloading compliance method. The experimental results for two kinds of ductile materials showed that the proposed method well simulates the material J-R curves. This method is currently applied for CT specimens. but it can be extended to the other specimen geometries.

• 대한수의학회지
• /
• 제61권3호
• /
• pp.20.1-20.9
• /
• 2021

This study is to develop a new scoring system for rating Hazard analysis and critical control points prerequisite evaluation items for meat shops to provide a more objective and accurate evaluation of food safety compliance. The importance of each item was measured by looking at the hazard severity level and the rate of non-compliance associated with it. It was found that the new scoring system is more stringent and gives a clearer picture of compliance with the most critical safety standards, and therefore is expected to have a positive effect on the hygiene and safety of livestock products.

• The Journal of Asian Finance, Economics and Business
• /
• 제7권12호
• /
• pp.1175-1184
• /
• 2020

This research examines the personal (i.e., Machiavellianism) and situational factors (i.e., tax climate) that are believed to be psychologically salient aspects in tax compliance. To the best of our knowledge, no research has been carried out to investigate the interaction effect of the two factors. This study uses a paper-and-pencil laboratory experiment 2x2 between-subject factorial design that involved 158 participants. The results indicate that a taxpayer who has a low Machiavellianism score or who is in a high synergistic tax climate reports a higher level of income. In the high synergistic tax climate, where tax norms apply, personal ethics do not play a significant role in tax compliance decisions. Where the synergistic relationship between taxpayer and authorities is low, personal ethics play an important role, i.e., low Machiavellians report a higher reported income than high Machiavellians do. This research contributes to the literature that deviates from the traditional model of tax compliance. Taxpayers are not always rational, but they might pay tax for reasons other than financial motives (Alm, 1991, 2018), that is, personal ethics in this study. This research implies the need for policymakers to consider other approaches rather than only relying on audits and fines.

• 임상간호연구
• /
• 제22권3호
• /
• pp.257-264
• /
• 2016

Purpose: The purpose of this study was to explore the effect of individualized diet education program on dietary knowledge and self-care compliance among hemodialysis patients. Methods: The design of the study was quasi-experimental nonequivalent control group pre-post test design. Fifty patients were assigned to an experimental group and fifty patients were assigned to a control group. Individualized diet education program was applied to the experimental group once every two weeks for twelve weeks. Results: Dietary knowledge increased significantly in the experimental group when compared to the control group. Dietary self-care compliance improved significantly in the post-test of the experimental group, however, the difference was not significant. Conclusion: The individualized dietary education program was effective in improving dietary knowledge. The individualized diet education program needs to be incorporated as an important nursing intervention. Nurses should provide individualized diet education program for hemodialysis patients.

• Journal of Welding and Joining
• /
• 제5권2호
• /
• pp.44-52
• /
• 1987

The fracture toughness, $J_{IC}$ of high frequency electric resistance welded steel pipe for smooth and side-grooved CT specimen was evaluated by unloading compliance method. The crack growth, .${\delta}a$ was obtained from the equation of Donald and Saxena & Hudak, and $J_{IC}$ was determined from the curve of J-${\delta}a$ relations. The crack growth on the experiment using unloading compliance method is underestimated as compared with ${\delta}a$ measured directly by the SEM, so the reliability of $J_{IC}$ from saxena & Hudak equation is large than that from Donald. The $J_{IC}$ value of side-grooved CT Specimen is estimated less than that of smooth, and this is the effect of the side-groove, the shear-lip of crack tip and the reduction of crack tunnelling phenomena.