• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.111-115
• /
• 2002

The objective of this work is to develop improved slip factor model and correction method to predict flow through impeller in forward-curved centrifugal fan by investigating the validity of various slip factor models. Both steady and unsteady three-dimensional CFD analyses were performed with a commercial code tn validate the slip factor model and the correction method. The results show that the improved slip factor model presented in this paper could provide more accurate predictions for forward-curved centrifugal impeller than the other slip factor models since the presented model takes into account the effect of blade curvature. The comparison with CFD results also shows that the improved slip factor model coupled with the present correction method provides accurate predictions for mass-averaged absolute circumferential velocity at the exit of impeller near and above the flow rate of peaktotal pressure coefficient.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.3
• /
• pp.219-230
• /
• 2004

Most of the low-level liquid radioactive wastes generated from PWR plants are classified into high or low total suspended solid(HTDS or LTDS), and into radiochemical and radioactive laundry waste. Although the evaporation process has a high decontami- nation ability, it has several problems such as corrosion, foam, and congestion. A new liquid waste disposal process using the ion-exchange demineralizer(IED), instead of the current evaporation process, has been introduced into the Yonggwang NPP #5 and 6. These two methods have been compared to understand the differences in this study. Aspects compared here were the released radioactivity amount of the liquid radioactive wastes, the dose of off-site residents, the decontamination factor, and the amount of the solid radioactive wastes. The IED system is designed to discharge higher radioactivity about 20% than the evaporating system, and the actual radioactivity released from the evaporating and IED system were 0.473mCi and 1.098mCi, respectively. The radioactivity released from the IED was 2.32 times higher than that of the evaporating system. The dose of off-site residents was $2.97{\times}10^{-6}$mSv for the evaporating system, and $6.47{\times}10^{-6}$mSv for IED. The decontamination factor(DF) of the evaporator is, in most cases, far lower than the lower limits of detection(LLD) with the Ge-Li detector. Due to the low concentration of the liquid wastes collected from the liquid waste system, the decontamination factor of IED is very low. Since there is not enough data on the amount of solid radioactive wastes generated by the evaporation system, the comparison on these two systems has been conducted on the basis of the design, and the comparison result was that the evaporating system generated more wastes about 40% than IED.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.290-293
• /
• 2000

In this paper the algorithm which controls output voltage and power factor independently and the algorithm which controls output voltage with fixed unity power factor are compared and analyzed. These algorithms are applied to single-phase AC/DC parallel are applied to single-phase AC/DC parallel converters for a high speed train system. The control characteristic of the algorithms are compared and analyzed with respect to the output voltage and input power factor when system parameters vary.

• Journal of Industrial Technology
• /
• v.18
• /
• pp.165-172
• /
• 1998

In recent years, various power factor correction(PFC) circuits for the electronic ballast have been proposed. And these circuits have difference characteristics each other. We have researched several PFC circuits of them. And operational principles and characteristics of PFC circuits are compared by the cost and the electrical performance. Finally, we established the reference for the evaluation of PFC circuits with performance and the price.

• Journal of the Korean Society of Safety
• /
• v.35 no.3
• /
• pp.49-57
• /
• 2020

In comparison with the existing static reliability analysis methods, the dynamic reliability analysis(DyRA) method is more suitable for estimating the failure probability of a structure subjected to earthquake excitations because it can take into account the frequency characteristics and damping capacity of the structure. However, the DyRA is known to have an issue of numerical stability due to the uncertainty in random sampling of the earthquake excitations. In order to solve this numerical stability issue in the DyRA approach, this study proposed two earthquake-scale factors. The first factor is defined as the ratio of the first earthquake excitation over the maximum value of the remaining excitations, and the second factor is defined as the condition number of the matrix consisting of the earthquake excitations. Then, we have performed parametric studies of two factors on numerical stability of the DyRA method. In illustrative example, it was clearly confirmed that the two factors can be used to verify the numerical stability of the proposed DyRA method. However, there exists a difference between the two factors. The first factor showed some overlapping region between the stable results and the unstable results so that it requires some additional reliability analysis to guarantee the stability of the DyRA method. On the contrary, the second factor clearly distinguished the stable and unstable results of the DyRA method without any overlapping region. Therefore, the second factor can be said to be better than the first factor as the criterion to determine whether or not the proposed DyRA method guarantees its numerical stability. In addition, the accuracy of the numerical analysis results of the proposed DyRA has been verified in comparison with those of the existing first-order reliability method(FORM), Monte Carlo simulation(MCS) method and subset simulation method(SSM). The comparative results confirmed that the proposed DyRA method can provide accurate and reliable estimation of the structural failure probability while maintaining the superior numerical efficiency over the existing methods.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.23 no.4
• /
• pp.1-17
• /
• 2021

This study was examined whether the experiential marketing factors proposed by Bernd Schmitt were applicable to the consumer behavior of active seniors. The study was analyzed the influence of SEMs have on value perception of brand and attitude formation as well as the behavioral intentions of active senior consumers and whether this effect differed between the level of commitment. For empirical analysis, frequency analysis, EFA, reliability, CFA, SEM, and multiple-group comparison analysis were performed. The results showed that sense and feel factor did not have a significant influence on the value perception of brand, while think factor had a positive effect on the value perception of brand. Act factor did not affect the value perception of brand; on the other hand, relate factor had a significant effect on the value perception of brand. The result of structural equation modeling also revealed that the value perception of brand had a positive influence on attitude formation and behavioral intentions. The result of multiple-group comparison analysis confirmed that the influence of act factor on value perception of brand differed according to the level of commitment, but the positive influence of act factor on value perception of brand was limited to the high-level of commitment group. As a result of the influence relate factor had on the value perception of brand, differences existed between the two groups, and the low-level of commitment group had a greater influence than the high-level of commitment group. So it will be effective for active senior consumers to form fashion communities and let them participate in to enhance positive consumer behavior toward fashion brands.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.568-571
• /
• 1997

The overall aim of this paper is to determine coupling loss factor using loss factor and structural loss factor. For this purpose, two kinds of loss factor were adopted. One is loss factor of each sub structure, another is structural loss factor based on the complex welded or assembled structure. Using these two parameters, it is possible to derive the coupling loss factor which represent characteristic condition of SEA theory. Coupling loss factor of conjunction in complex structure was expressed as power balance equation. The derived equation for a coupling loss factor has been simplified on the assumption of one directional power flow between two sub structures. Using these conditions, it is possible to find the coupling loss factor equation. The comparison between theory of power transmission on conjunction and above equation, show a good agreement in simple beam structure. To check the effectiveness of above equation, it was adopted rotary compressor. Rotary compressor has three main conjunctions between shell and internal vibration part. This equation was applied to find out the optimum welding point with respect to reduce the noise propagation. It shows the effective tool to evaluate the coupling loss factor in complex structure.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.302-312
• /
• 2004

This work developed improved slip factor model and correction method to predict flow through impeller in forward-curved centrifugal fan. Both steady and unsteady three-dimensional CFD analyses were performed to validate the slip factor model and the correction method. The results show that the improved slip factor model presented in this paper could provide more accurate predictions for forward-curved centrifugal impeller than the other slip factor models since the present model takes into account the effect of blade curvature. The correction method is provided to predict mass-averaged absolute circumferential velocity at the exit of impeller by taking account of blockage effects induced by the large-scale backflow near the front plate and flow separation within blade passage. The comparison with CFD results also shows that the improved slip factor model coupled with the present correction method provides accurate predictions for mass-averaged absolute circumferential velocity at the exit of impeller near and above the flow rate of peak total pressure coefficient.

• The Korean Journal of Community Living Science
• /
• v.16 no.3
• /
• pp.57-64
• /
• 2005

The purpose of this study was to compare clothing attitudes and the criteria for clothing selection between Korean and Korean-Chinese college female students in the Yanbian region of China. The subjects were selected as follows: 404 Korean female college students in the Choongchung area and 242 Korean-Chinese female college students in the Yanbian region of China. Questionnaires were used to collect the data and the data was analyzed by frequency, factor analysis, and t-test. The major results of this study were as follows: The clothing attitudes of the total respondents were classified into 5 factors: the fashion involving factor, the modesty involving factor, the economy conscious factor, the brand-name oriented factor, and the practical user factor. The modesty involving factor, the economy conscious factor, the brand-name oriented factor, and the practical user factor were significantly different between Korean and Korean-Chinese college female students. Korean consumers thought highly of the economy conscious factor and the practical user factor compared with Korean-Chinese college female students. However, Korean-Chinese college female students thought highly of the brand-name oriented factor and the modesty factor compared with Korean consumers.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.15 no.3
• /
• pp.1-17
• /
• 2013

The purpose of this study was to identify the relationships among self-esteem, physical appearance comparison, media concern, sociocultural attitude toward appearance, body attitudes, and life satisfaction. Data were collected from a convenience sample of 232 female undergraduate students. Data were analyzed using factor analysis, correlation, and multiple regression. The result showed that there was a correlation between physical appearance comparison and media concern. Self-esteem, physical appearance comparison, and media concern had an indirect influence on body attitudes through sociocultural attitude toward appearance. Self-esteem and physical appearance comparison had a direct effect on body attitude. All variables did not have an influence on life satisfaction, except self-esteem.