• Journal of Convergence Society for SMB
• /
• v.6 no.4
• /
• pp.25-30
• /
• 2016

This paper presents on the development of a compact anti-lost device requested recently. The proposed device consists of the master and slave modules based on Bluetooth4.1 technology. To implement a low-power characteristic, an algorithm has been also developed. The transmitting and receiving circuits are designed by using BoT CLE110 module supporting Bluetooth 4.1. The ATmega 328P-AU was used for the control and LP3874EMP was used as a linear regulator. Power consumption of the fabricated product in operating mode is only 10mAh and 35mAh for MCU operating state. Alarm operation distance is $10m{\pm}30%$, the effective radiated power is less than 10mW, the frequency band is designed to operate in the Bluetooth band with 26MHz bandwidth. And algorithms have been developed to extend the battery life. The size of the product was obtained as $45{\times}45{\times}15mm$ for master and $35{\times}35{\times}10mm$ fr slave. After the optimization process, it is expected to be commercialized as a wristwatch for anti-lost device.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1619-1619
• /
• 2001

Ourwork aims to assess the content of dry matter, protein, cell wall parameters and water soluble carbohydrates in forages without having to handle samples, transport them to a laboratory, dry, grind and chemically analyze them. for this purpose, the concept of fresh forage analysis under field conditions by means of compact integrated NIRS InGaAs-diode array instruments on small plot harvesters is being evaluated for plant breeding trials. This work was performed with the world first commercial experimental forage plot harvester equipped with a NIRS module for the collection, compression, and scanning of forage samples (including automatic referencing and dark current measure ments). It was used for harvesting and analyzing a number of typical forage grass and forage legume plot trials. After NIRS measurements in the field each sample was again analyzed in the laboratory by means of a conventional grating spectrometer equipped with Si-and PbS-detectors. Conventional laboratory analysis of the samples was restricted to dry matter (DM) content by means of oven drying at 105. Routine chemometric procedures were then employed to assess the comparative accuracy and precision of the DM assessments in the spectral range between 950 and 1650nm by the NIRS diode array as well as by the conventional NIRS scanning instrument. The results of this study confirmed that the type of NIRS diode array instrument employed here functioned well even in rugged field operations. further refinements proved to be necessary for optimizing the automatic filling of the sample compartment to adjust for the wide variation in forage material under conditions of extremely low or high harvest yields. The error achieved in calibrating the apparatus for forages of typical DM content proved to be satisfactory (SECV < 1.0). Possibly as a consequence of higher sampling errors, its performance in atypical forages with elevated DM contents was less satisfactory. The error level obtained on the conventional grating NIR spectrometer was similar to that of the diode array instrument for both types of forage.

• Journal of Broadcast Engineering
• /
• v.18 no.1
• /
• pp.88-97
• /
• 2013

Collaborative filtering(CF) for the personalized recommendation is a successful and popular method in recommender systems. But the mainly researched and implemented cases focus on dealing with independent items with explicit feedback by users. For the domain of TV program recommendation in VOD service platform, we need to consider the unique characteristic and constraints of the domain. In this paper, we studied on the way to convert the viewing history of each TV program episodes to the TV program preference by considering the series structure of TV program. The former is implicit for personalized preference, but the latter tells quite explicitly about the persistent preference. Collaborative filtering is done by the unit of series while data gathering and final recommendation is done by the unit of episodes. As a result, we modified CF to make it more suitable for the domain of TV program VOD recommendation. Our experimental study shows that it is more precise in performance, yet more compact in calculation compared to the plain CF approaches. It can be combined with other existing CF techniques as an algorithm module.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.4
• /
• pp.707-714
• /
• 2016

Active driving safety systems for vehicle, such as the front collision avoidance, lane departure warning, and lane change assistance, have been popular to be adopted to the compact car. For improving performance and competitive cost, FMCW radar has been researched to adopt a phased array or a multi-beam antenna, and to integrate the front and the side radar. In this paper we propose several efficient methods to implement the signal processing module of FMCW radar system using low cost DSP. The pulse width modulation (PWM) based analog conversion, the approximation of time-eating functions, and the adoption of vector-based computation, etc, are proposed and implemented. The implemented signal processing board shows the real-time performance of 1.4ms pulse repetition interval (PRI) with 1024pt-FFT. In real road we verify the radar performance under real-time constraints of 10Hz update time.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.74-78
• /
• 2004

We propose a servo control method using a dome-type glass in shift-multiplexed holographic data storage. We frist store live 2-D data by shift-multiplexing in a holographic disk with 5％ variation in their. diffraction efficiencies. During read-out of the stored data, the servo control using the dome glass correctly compensates mechanical errors of the disk; the error of $\pm$0.2$^{\circ}$and run-out error of $\pm$50 ${\mu}{\textrm}{m}$. Use of the dome-type glass in servo control makes a pickup module more compact in size and easier to control than the previous method using parallel glass plate ［Sungphil Kim, et al., Hankook Kwanghak Hoeji, Vol. 14, No. 1, pp.58-64, 2003］.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.6
• /
• pp.161-167
• /
• 2017

Recently, small radar has been reduced in size and power consumption to cope with various operating environments. It also requires the development of a small millimeter wave radar with high range resolution to disable the system of target with a single strike. In this paper, we design and implement a signal processor that can be used in small millimeter wave radar. The signal processor for the small millmeter wave radar is designed with a digital IF(Intermediate Frequency) receiver and DFT(Discrete Fourier Transform) module capable of real time FFT operation for miniaturization and low power consumption. Also it was to leverage the FPGA(Field Programmable Gate Array) and DAC(Digital Analog Converter) as a means for correcting the distortion of signals that can occur in the receive path of the small millimeter wave radar to create a RF signal that is used by the system. Finally, we verified the signal processor presented through performance test

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.136-139
• /
• 2011

The conventional semiconductor equipment has adopted SRAM module as the test pattern memory, which has a simple design and does not require refreshing. However, SRAM has its disadvantages as it takes up more space as its capacity becomes larger, making it difficult to meet the requirements of large memories and compact size. if DRAM is adopted as the semiconductor inspection equipment, it takes up less space and costs less than SRAM. However, DRAM is also disadvantageous because it requires the memory cell refresh, which is not suitable for the semiconductor examination equipments that require correct timing. Therefore, In this paper, we will proposed an algorithm for punctuality guarantee of memory-free inspection equipment using DDR2 SDRAM. And we will produced memory controller using punctuality guarantee algorithm.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.2
• /
• pp.124-133
• /
• 1998

This paper describes a research work of developing a computer-aided design of blanking and piercing for irregular-shaped sheet metal products. An approach to the development of compact and practical CAB system is based on the knowledge-based rules. Knowledge for the CAD system is formulated from plasticity theories, experimental results and the empirical knowledge of field experts. The system has been written in AutoLISP on the AutoCAD with a personal computer. Based on knowledge-based rules, the system, STRT-DES, is designed by considering several factors, such as complexities of blank geometry and punch profile, availability of press equipment and standard parts, utilization ratio which minimizes the scrap in a single or a pairwise operation, bridge width, grain orientation and design requirements which maximize the strength of the part when subsequent bending is involved. This system checks a forming feasibility with both internal and external features, a dimension of blanked hole, and a corner and a fillet radius for irregualrly shaped sheet metal products. Therefore this system can carry out a die design for each process which is obtained from results of an automated blank layout drawing with a best utilization ratio for irregular shape of product that was successful in production feasibility check module and those of an automated strip layout drawing and generate part drawings and the assembly drawing of die set in graphic forms.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.11
• /
• pp.34-39
• /
• 2002

In this paper, we proposed novel photonic bandgap(PBG) structure using EGP(Elevated Ground Plane) and via in ceramic substrate of microstrip line. From analysis result, the proposed PBG structure is reduced 52.5% at size and increased 45 % at bandwidth compared to typical planar PBG structure. It is also reduced 32 % at size and improved more than 8 dB at power loss compared to typical multilayer DGS(Defected Ground Structure). The proposed PBG structure also can be used bandstop and lowpass filter and it will be useful for small microwave integrated circuit and module development.

• Journal of Intelligence and Information Systems
• /
• v.14 no.4
• /
• pp.89-101
• /
• 2008

The most used tool for quality control is control chart in manufacturing industry. But it has limitations at current situation where most of manufacturing facilities are automated and several manufacturing processes have interdependent relationship such as CCM assembly line. To Solve problems, we propose quality management system based on data mining that are consisted of monitoring system where it monitors flows of processes at single window and feature extraction system where it predicts the yield of final product and identifies which processes have impact on the quality of final product. The quality management system uses decision tree, neural network, self-organizing map for data mining. We hope that the proposed system can help manufacturing process to produce stable quality of products and provides engineers useful information such as the predicted yield for current status, identification of causal processes for lots of abnormality.