• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.985-991
• /
• 2008

This paper presents a novel balanced mixer receiver front-end design based on a metamaterial structure applicable to differential-/common-mode excitation. This metamaterial structure functions as a leaky-wave antenna and provides in-trinsic common-mode suppression. Low LO leakage and high RF to LO isolation are achieved without additional filters for LO and RF paths. The metamaterial is based on a unit-cell which under a differential-mode excitation behaves like a composite right/left-handed(CRLH) metamaterial. In contrast, the metamaterial unit-cell is below cut-off under a common-mode excitation. Experimental results are used to verify the proposed metamaterial's differential-/common-mode characteristics. The metamaterial is integrated with a balanced mixer design resulting in an operation frequency range of $1.96{\sim}2.40$ GHz with an optimum mixer conversion loss of 21.1 dB at 2,4 GHz.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.4
• /
• pp.511-517
• /
• 1999

Determining the simultaneous flow rate in any particular section of piping is the important step in order to determine the size of water supply piping. Now we are using the diversity curve of common water closet in order to determine the simultaneous flow rate of water supply piping, but there is a difference between a determined flow rate of general water closet and that of water closet for water saving. This study aims to find out the fixture unit of a flush valve type water closet for water saving in office building, and to determine the correlation between the fixture units and peak flow rates on the basis of the probability theory. A flush valve type water closet for water saving that have a 7.5 second duration of flush operation with an average design flow rate 72 $\ell$/fin was considered. Simulation results indicate that the number 5 is shown to be reasonable to the fixture unit of water closet for water saving. And the design can be undersized considerably with the revised diversity curves using modified fixture unit.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.2
• /
• pp.279-288
• /
• 2017

The Material Transportation Capability Analysis Method in North Korea includes adversary's activities such as destruction of bridge which is one kind of choke points in the road network and surprise attack against resupply march unit. Also, the amount of damage on choke points in the road network and repair time depending on repair unit commitment must be reflected. In this study, a scenario encompassing plausible resupply transportation circumstances while counterattacking into NK will be established. Then, based on such scenario, a simulation model will be established and the result of simulation will be compared to the results of numeric example which has been used in the ROK Army. We demonstrate, through a certain Corps operation area, that the Scenario-based Simulation Model results predict the performance of resupply operation very well. Therefore, it makes sustainment planners and commanders do activities which is suitable for battlefield and should be used in the real situation. It is also a stochastic model.

• The Transactions of the Korea Information Processing Society
• /
• v.2 no.3
• /
• pp.397-405
• /
• 1995

In order to operate the automatic devices of manufacturing process more efficiently and to solve the needs of the resource sharing,network technology is applied to the unit control devices located in common manufacturing zone and operated by connecting them.In this paper,functional standard of the network operation layer is set as MAP standard application layer of MMS(manufacturing message standard)for the cell or group,which is suggested by CIM (computer integrated manufacturing) standardization as common manufacturing zone.MMS is composed of abstract message which is not consider specific devices.Then,specific message standard must be defined to operate MMS.It is designed as VMD (virtual manufacturing device)objects which are abstract objects to perform group management based on the companion standard.Also they are operated in the group management model system.Group management operation takes multicast communication method which is the communication from single source to the multiple sinks, and the group management system and unit control devices are performed as VMD and real device mapping.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.55-58
• /
• 2000

This paper describes a single transistor type ferroelectric field effect transistor (1T FeFET) memory celt scheme which can select one unit memory cell and program/read it. To solve the selection problem of 1T FeEET memory cell array, the row direction common well is electrically isolated from different adjacent row direction column. So, we can control voltage of common well line. By applying bias voltage to Gate and Well, respectively, we can implant IT FeEET memory cell scheme which no interface problem and can bit operation. The results of HSPICE simulations showed the successful operations of the proposed cell scheme.

• Journal of Mechanical Science and Technology
• /
• v.15 no.12
• /
• pp.1728-1738
• /
• 2001

Measurements have been made in an automotive HVAC b1ower for two different centrifugal fans. This work is directed at improving the performance of a conventional forward-curved centrifugal fan for a given small blower casing. Mean velocities and pressure have been measured using a miniature five-hole probe and a pressure scanning unit connected to an online data acquisition system. First, we obtained the fan performance versus flow rates showing a significant attenuation of unstable nature achieved with the new fan rotor in the surging operation range. Second, aerodynamic characterizations were carried out by investigating the velocity and pressure fields in the casing flow passage for different fan operating conditions. The measurements stowed that performance coefficients are strongly influenced by flow characteristics at the throat region. The main flow features ware common in both fans, but improved performance is achieved with tole new fan rotor, particularly in lower flow rate legions. Based on the measured results, design improvements were carried out in an acceptable operation range, which gave considerable insight into what features of flow behavior ware most important.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.838-848
• /
• 2018

This paper proposes a single-phase buck-boost AC-AC converter. It consists of three legs with six switching units (each unit is composed of an active switch and a diode) and its input and output ports share a common ground. It can provide buck-boost voltage operation and immune from shoot-through problem. Since only two switching units are involved in the current paths, the conduction losses are low, which improves the system efficiency. The operation principle of the proposed circuit is firstly presented, and then, various operation conditions are introduced to achieve different output voltages with step-changed frequencies. Additionally, the parameters design and comparative analysis of the power losses are also given. Finally, experimental results verify the correctness of the proposed converter.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.7 no.1
• /
• pp.85-92
• /
• 1969

The goal for the improvement of rice culture in our country is to increase the rice yield per unit area, and that thoroughly, to equalize the rice yield per unit are highly by adaptation of high technique, while on the side of the efficiency, to increase the productivity of the labour through the cooperative work. And then, the theory for execution of the cooperative rice culture which is the productive system embodying the goal above and the expected effects as well as the future prospect for the development of the cooperative rice culture must be studied and defined. The results studied up to now are summarized as follows: 1. The cooperative rice culture is one of the most effective ways to execute highly efficient farm management and to supply the technical details on the cultivation for equalized high yield per unit area in the rice cultivating districts. 2. For the most effective accomplishment of the cooperative rice culture, the water control, and soil and variety of rice must be investigated in advance an then the basic technical details for the rice culture must be defined. 3. The rice cultivation calender is drawn up with the main technical details of rice culture by the mutual agreement of all farmers belong to the cooperative farm. All technical details for the rice cultivation in the cooperative farm are standardized by the rice cultivation calendar and the main technical operations should be worked together and the other operations executed individually. 4. The technique for rice cultivation, which was difficult to be introduced in the individual farm management, could be introduced easily to the cooperative rice culture, and the rice yield of the cooperative farm was increased 23.3% compared to that of common farm in 1968. 5. At present, the type of the cooperative rice culture is a primary type of the agreement for farm management, rarely including the associated operation type and the contracted operation type for a part of operation, However, for stabilized high yield through the mechanization of the cultivation system, the cooperative farm must be developed for a course promoting the associated operation type including the technique trust type and the contracted operation type according to the condition of location.

• Convergence Security Journal
• /
• v.19 no.4
• /
• pp.13-22
• /
• 2019

The purpose of this study is to suggest the educational system and direction of cyber operations officers of non-cyber operations forces who do not specialize in cyber operations. In order to carry out cyber operations as a joint operation, non-Cyber Operations officers must also know about cyber operations, but there is no education system for them at present, Since there is almost no previous research on this, research in the relevant field is necessary. Therefore, the education system was developed based on the prior literature review, that is, the education system, that is, the necessity of education, the object of education, the goals and contents of the education, and the curriculum. In addition, the relevant experts confirmed the validity of each item with Delphi method, and as a result, some improvement was needed, but it was shown to be suitable as a whole. In addition, detailed educational program development can be developed based on this in the future.

• Journal of Korean Critical Care Nursing
• /
• v.2 no.1
• /
• pp.58-68
• /
• 2009

Purpose: The treatment effects and operation status of continuous renal replacement therapy (CRRT) for acute renal failure patients have been investigated. Method: Two expert nurses reviewed the records of 731 patients undergoing CRRT in an intensive care unit of a general hospital from Jan. 2002 to Dec. 2006 with the CRRT assessment sheet and situation sheet developed for this study. Results: The number of patients received CRRT increased from 90 in 2002 to 194 in 2006. The most common indication for CRRT was azotemia (40.0%). Before CRRT treatment, patients were 78.6 ($\pm55.5$) of BUN value and 5.0 ($\pm3.2$) of Cr. value. The standard values of BUN and Cr. were lowered. Compared the survival group with the death group, there were significant differences among the medical departments and the main diagnosis group. Their BUN and creatinine value, APACHE II score, mean blood pressure, and oliguria were significantly different (p<0.05). Conclusion: This survey demonstrates a trend that patients receiving CRRT has been increased. We suggest further studies are needed in some hospitals in order to generalize the results and to find how CRRT treatment affects patient’s survival and death rate.