• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.139-142
• /
• 2009

As important mechanical elements, gears have been used widely in power transferring systems such as automobile transmission and there have been several researches trying to make gear parts with cold or warm forging in order to reduce cost and time required to gear manufacturing process. Although forging processes of spur and bevel gears have been developed as practical level owing to active previous researches in Korea, the manufacturing of helical gear has been still depended on traditional gear cutting processes such as hobbing, deburring and shaving. In order to manufacture helical gears with cold forging process, a research project supported by government has been conducted by Daegu university, KIMS and TAK and this paper deals with effects of back pressure forming technique to cold forging of helical gear as a fundamental research.

• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.157-163
• /
• 1993

Hot pressing after cold cyclic compaction of Al2O3 powder mixtures containing SiC whiskers or Al2O3 short fibers is studied with emphasis on the effects of cold cyclic compaction. The green density of the mixtures increases as the cycle number increases and the cyclic pressure becomes higher. The higher green density is also obtained by cold cyclic compaction with the lower pressrue than a single stroke cold compaction. To achieve a higher densification during hot pressing, cold cyclic compaction before hot pressing is more efficient compared to the conventional hot pressing process (without cold cyclic compaction). Moreover, a low cyclic pressure did not affect on toughening mechanism by whisker reinforcement.

• 동의생리병리학회지
• /
• 제33권4호
• /
• pp.226-232
• /
• 2019

This study was aimed to reveal that the usual cold or heat state was associated with hypertension and could be a risk. We emailed educational personnel in D university to join this study and 182 subjects participated in from March to December in 2016. The usual cold or heat diagnosis was conducted by two experts who had over 10 years expertise. The blood pressure was measured from the subjected after 10 minute rest with Jawon medical device. The hypertension was diagnosed by the guide of the Seventh Report of the Joint National Committee on Prevention, Detection, Evaluation, and Treatment of High Blood Pressure. The frequency analysis was used in general characteristics, Pearson's Correlation Coefficient analysis was conducted in among continuous variables, and chi-square test was also used between hypertension and cold or heat group. Logistic regression was analyzed to generate the odds ratios (ORs) and 95% confidence interval (CI) for hypertension. The cold score was suggested to have negative association with Body mass Index (BMI, -.374, p<.001), systolic blood pressure (-.333, p<.001), and diastolic pressure (-.261, p<.001). The heat score was analyzed to have positive association with Body mass Index (.413, p<.001), systolic blood pressure (.249, p<.001), and diastolic pressure (.156, p<.001). The distribution of the cold group (35.1%) and non-cold group (64.9%) in hypertension was significantly different (p=0.18). The distribution of the heat group (62.2%) and non-heat group (37.8%) was significantly different (p=0.27). The usual cold was associated with decreased ORs (ORs 0.405, 95% CI=0.191-0.857), and usual heat was associated with increased ORs (ORs 2.327, 95% CI=1.108-4.888). However, after adjusting body mass index, sex, and smoking, the association was not significantly different. It is possible that usual cold or heat associate with hypertension. Further study is needed to show that usual heat may be a independent risk factor for hypertension through follow up design.

• Journal of Welding and Joining
• /
• 제5권3호
• /
• pp.19-27
• /
• 1987

This paper presents the weldability for cold pressure but welding method in junction of dissimilar metals each other. Although the weldability between the same aluminium metal plate welding has been studied, the study of itthe rod of aluminium and coper has not fully been investigated. The purpose is to suggest the optimal conditions on the rod of those under above method. To obtain the optimal conditions, associated experiments were performed in a various welding parameters. Consequently, it was proved that the mechanical properties such as tensile strength, hardness and bending strength could be obtained excellent particularly under the welding conditions; pressure is $(32~39) {\times} 10^3/kg/cm^2$, time is beyond 70 seconds, stage is higher than fifth stage.

• 대한치과보철학회지
• /
• 제31권3호
• /
• pp.385-393
• /
• 1993

Injection processing of denture base resin was introduced by Pryer in 1942, in an attempt to reduce processing shrinkage. More recently a continuous-pressure injection type technique has been developed (SR-Ivocap, Ivoclar AG, Schaan, Liechtenstein.), and it reduced processing error and increased resin density. The purpose of this study was to compare tensile bond strength of heat-cured, cold-cured, and light-cured denture base resin bonded to continuous-pressure injection type resin. To know it, 60 cylindrical resin specimens were fabricated, and tensile bond strength were measured. The results were as follows : 1. The mean tensile bond strength bonded to continuous-pressure injection type resin was lower than bonded to conventional heat cured resin. But tensile bond strength of conventional heat cured resin bonding with light cured resin was lower than continuous-pressure injection type resin. 2. Of the tensile bond strength bonded to continuous-pressure injection type resin, tensile bond strength bonding with continuous-pressure injection type resin was the greatest(but not significantly different from bonding with conventional heat cured resin), followed by cold-cured, light-cured resin. 3. Of the tensile bond strength bonded to conventional heat cured resin, tensile bond strength bonding with conventional heat cured resin was the greatest and followed by continuous-pressure injection type resin, cold-cured resin, light-cured resin. According to these results, bonding of continuous-pressure injection type resin with conventional heat cured resin or continuous-pressure injection type resin is acceptable, but bonding with light-cured resin is questionable.

• 농업과학연구
• /
• 제45권1호
• /
• pp.94-104
• /
• 2018

Nitrite is an essential additive for cured meat product. Plasma is ionized gas and reactive nitrogen species in plasma can be infused into meat batter and subsequently generate nitrites by reaction with water molecules after plasma treatment. However, the increase of nitrite in meat batter is limited with direct treatment of atmospheric pressure cold plasma because of the increase of meat batter temperature. Therefore, this study investigated the influence of indirect treatment of atmospheric pressure cold plasma on the physicochemical properties of meat batter. Meat batter was indirectly treated with plasma at 1.5 kW for 60 min. The pH of meat batter decreased while the temperature increased with plasma treatment time. The total aerobic bacterial count of meat batter was not affected by plasma treatment. The nitrite content of meat batter was increased to 377.68 mg/kg after 60 min of plasma treatment. The residual nitrite content of cooked meat batter also increased with plasma treatment time. The CIE $a^*$-value of cooked meat batter increased. As plasma treatment time increased, lipid oxidation tended to increase and protein oxidation significantly increased. According to these results, the indirect treatment of atmospheric pressure cold plasma can be used as a new curing method for replacing synthetic nitrite salts.

• 설비공학논문집
• /
• 제7권1호
• /
• pp.120-131
• /
• 1995

Thermodynamic analysis of extraction process from the constant pressure LNG(Liquefied Natural Gas) vessel was performed in this study. LNG was assumed as a binary mixture of 90% methane and 10% ethane by mole fraction. The thermodynamic properties such as temperature, composition, specific volume and the amount of cold energy were predicted during extraction process. Pressure as a parameter ranges from 101.3kPa to 2000kPa. The result shows the peculiar phenomena for the LNG as a mixture. Both vapor and liquid extraction processes were investigated by a computer model. The property changes are negligible in the liquid extraction process. For the vapor extraction process, the temperature in the vessel increases rapidly and the extracted composition of methane decreases rapidly near the end of extracting process. Specific volume of vapor has the maximum and that of liquid has the minimum during the process. When pressure is increased, specific volume of vapor decreases and that of liquid increases. It was found that specific volume of vapor phase had a major effect on the heat absorption at constant pressure during vapor extraction process. If the pressure of the vessel increases, the total cold energy which can be utilized from LNG decreased.

• 대기
• /
• 제28권4호
• /
• pp.383-392
• /
• 2018

This study investigates synoptic characteristics of cold surges over South Korea during winter season (December-February). A total of 63 cold events are selected by quantile regression analysis using daily mean temperature observations from 11 KMA stations for 38 years (1979/80-2016/17). Large-scale pressure pattern during the cold surges is well characterized by high over Siberia and low over Aleutian regions, which elucidates cold advection over the Korean peninsula. However, the large-scale pattern cannot successfully explain the observed sudden decrease of temperature during the cold surges. Composite analyses reveal that a synoptic-scale cyclone developing over the northern Japan is a key feature that significantly contribute to the enhancement of cold advection by increasing pressure gradient over the Korean peninsula. Enhanced sensible and latent heat fluxes are observed over the southern ocean of Korea and Japan during the cold surges due to temperature and humidity differences between the near surface and the lower atmosphere over the ocean. The evaporated water vapor transported toward the center of the surface cyclone and condenses in the lower-to-middle troposphere. The released energy likely promotes the development of the surface cyclone by inducing positive PV near the surface of the heating region.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권8호
• /
• pp.1116-1122
• /
• 2009

냉동냉장창고 내 열부하 감소를 위한 유압 구동식 냉각기의 특성을 실험적으로 평가한 결과 고내 온도강하에 있어서 초기에는 급격하게 이루어지고, 설정온도가 낮아질수록 온도 강하율은 적게 나타났다. 기존 전기 구동식과 비교한 결과 유압식이 더 빠른 온도 강하율과 냉동기 운전시간이 짧게 나타나 실제냉동창고의 경우, 입고 물품의 품질저하 방지 및 전력 절감에 기여할 수 있을 것으로 판단되었다. 그리고 고내 설정온도가 낮을수록 소비동력은 급격히 증가하였고, 유압식이 더 적은 동력을 소비하는 것으로 나타났으며, 두 방식 모두 설정온도에 도달함에 따라 성능계수는 지속적으로 저하하였고, 유압식이 최대 25%정도 높게 나타났다. 고내 온도유지에 있어서는 설정온도가 낮을수록 냉동기의 운전 횟수가 적고, 운전시간이 길어 소비동력이 많아지는 것으로 나타났으며, 유압식이 약 21~25%정도 적게 나타났다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.97-101
• /
• 2001

Fine metal (Au, Ag, Cu) wire was extruded with hydrostatic extrusion process in cold condition. A vertical type 900kN hydrostatic extruder has been developed. The extruder was facilitated with high pressure container which are available for hot and cold forming. The container endured 1400MPa internal pressure and extrusion ratio To was achieved in cold forming for Au fine wire which had $600{\mu}m$ diameter. In contrast to the conventional macroscopic-sized-billet fine-wire requires higher extrusion pressure and effect of friction is much more significant.