• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2105-2107
• /
• 2004

In this study, Spiral inductors on the $SiO_2$/Si(100) substrate were fabricated by the magnetron sputtering method. Cu thin film with the thickness of 2 ${\mu}m$ was deposited on the substrate. Also we fabricated square inductors through the wet chemical etching technique. The inductors are completely specified by the turn width and the spacing between spirals. Both the width and spacing between spirals were varied from 10 to 60 ${\mu}m$ and from 20 to 70 ${\mu}m$, respectively. Inductance and Q factor dependent on the RF frequency were investigated to analyze performance of inductor arrays. Also, We recommend that the reasonable Q-factors, spec's turns and thickness of the coil for inductors cab be set to be ideal condition.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.5
• /
• pp.1187-1191
• /
• 2010

$^1H-^{15}N$ heteronuclear dipolar coupling solid-state NMR experiments on lipid bilayer or bicelle samples are very useful for the structural studies of membrane proteins. However, to study these biological samples using solid-state NMR, a specific probe with high efficiency and high capability is required. In this paper, we describe the optimized design, construction, and efficiency of a 400 MHz wide-bore $^1H-^{15}N$ solid-state NMR probe with 5-mm solenoidal rf coil for high power, multi-pulse sequence experiments, such as 2D PISEMA or 2D SAMMY.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.38-40
• /
• 2001

Fiber-optic current sensor was developed using the Faraday effect to measure the electrical current on high-voltage lines. A twisted single-mode optical fiber was used as a sensor coil to suppress birefringence effect, enhancing performance against environmental perturbations. In this paper, we report the basic design considerations and the preliminary experimental results carried out in the 1000 A input current range.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1642-1646
• /
• 2011

One of the rolling stocks, low floor tram is recognized as the important alternative to improve traffic and environmental problems. There are many advantages of tram transportation system. It has, especially, low construction costs and easy accessibility. Trams operate with vehicles on roadways. The bogie configuration including traction motor of tramcar is different from that of conventional electric trains because tram has lower floor than train. In these reasons, the traction motors of tramcar are exposed to dusts, water and so on. Therefore, motors are designed by totally enclosed type. In this paper, we explain the design and test of totally enclosed traction motor for tramcar. Characteristic tests and temperature-rising tests were carried out in order to predict the performance of motor and the maximum temperature of coil.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.693-696
• /
• 2011

The SRM (Switched Reluctance Motor) is composed of silicon steel plates where the rotor structure is simple and laminated without coil winding or permanent magnet, making it mechanically robust and its maintenance and repair excellent. Applying SRM as traction motor for railway vehicle is given consideration because of its ruggedness capability in severe loading condition and its compact structure. Optimal design of SRM is needed to reduce torque ripple to apply SRM for railway traction drive because SRM has high torque ripple. In this paper, switched reluctance motor with three different stator pole shapes is taken for magnetic analysis using 3d finite element method to apply SRM as traction drive for railway vehicle. It is observed that the model 3 added Tooth Tang Depth and Slot Round to stator shape gives the improved inductance and torque characteristic.

• Transactions of Materials Processing
• /
• v.23 no.2
• /
• pp.75-81
• /
• 2014

Progressive dies are used for metal stamping during which multiple operations are performed in a sequence. Material is fed automatically from a coil into the press and advances from one die station to the next with each press stroke. Transfer dies are used in high-volume manufacturing for round, deep-drawn, and medium-to-large parts. Several different operations may be incorporated within a transfer die such as blanking, bending, piercing, trimming, and deep drawing. The main challenge in the current study is how to deform a seat cushion panel meeting the design specifications without any defects. A complex automation die manufacturing technology for the automotive seat cushion panel, mixing both semi-progressive die and transfer die for continuous production, was developed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.431-431
• /
• 2012

A compact tokamak reactor concept as a 14 MeV neutron source is desirable from an economic viewpoint for a fusion-driven transmutation reactor. LAR (Low Aspect Ratio) tokamak allows a potential of high "see full txt" operation with high bootstrap current fractions and can be used for a compact fusion neutron source. For the optimal design of a reactor, a radial build of reactor components has to be determined by considering the plasma physics and engineering constraints which inter-relate various reactor components and are constrained to use ITER physics and technology. In a transmutation reactor, the blanket should produce enough tritium for tritium self-sufficiency and the neutron multiplication factor, keff should be less than 0.95 to maintain sub-criticality. The shield should provide sufficient protection for the superconducting toroidal field (TF) coil against radiation damage and heating effects of the fusion neutrons, fission neutrons, and secondary gammas. In this work, characteristics of transmutation reactor based on LAR tokamak is investigated by using the coupled system analysis.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.457-460
• /
• 2005

When a hearing aid' s user is listening through telephone or cellular phone, he/she usually suffers from severe electrical magnetic interference noise. It is because hearing aids amplify voice signal as well as background noise. A telecoil, an induction coil, is a possible solution for the problem. Because a telecoil has the characteristic of high pass filter, it has some problem of resulting increased high frequency noise. For solving this problem, we can use a capacitor connected with the telecoil in parallel. According to capacitance, receiving signal quality may change. In this paper, proper capacitor values for the best sound quality are investigated by experimental work.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.741-743
• /
• 2004

In this paper, we describe a Control Element Drive Mechanism(CEDM) operation test using a Power Controller. By testing, we can catch the mechanical and electrical characteristics of CEDM and obtain the information about the improvement of CEDM and the design of CEDM power cabinet. The power controller for CEDM introduced in this paper can input firing angles directly into gate drive circuits of thyristors so that this method can be used to derive the maximum and minimum values of firing angles within available limits for a 3-phase half-wave rectifier. Angle inputs help us understand each coil's response characteristics. Since this power controller generates a serial sequence for CEDM insertion and withdrawal operations, we may judge whether CEDM works correctly as expected or not in each phase of a step movement.

• 전기의세계
• /
• v.21 no.3
• /
• pp.41-47
• /
• 1972

The requirements of a successful design for single phase induction motors with a high efficiency have, in recent years, led to the use of non-quadrature stator windings motors in which a high starting torque is a prime requisite. The capacitor motor is one of above machines in which various possible forms of asymmetry can be occur. These forms of asymmetry in the stator phase windings, encountered in machine designs, are 1) an asymmetrical disposition in space of their magnetic axes, 2) a difference in their effective number of turns, 3) a difference in the distribution of their coil groups per pole and 4) amounts of capacitance of an auxiary winding. In order to apply the effective performance prediction of these form to motors, mading of lower quality-domestic magnetic materials, the analysis and the experimental investigations of its sample motors are described in this paper. The utility of such a motor is demonstrated and it is shown that the effects- a good efficiency, good power factor and high starting torque-of the motor mechanism with non-quadrature stator phase windings can development disadvantages by using the lower quality-domestis magnetic materials.