• Journal of the Korea Safety Management & Science
• /
• v.20 no.2
• /
• pp.1-8
• /
• 2018

This study aims to provide a real-time information to the driver by effectively operating the advanced safety device attached to the freight vehicle, thereby minimizing insecure behavior of the driver such as speeding, rapid acceleration, sudden braking, And improve driving habits to prevent accidents and save energy. Advanced safety equipment is a device that warns the driver that the vehicle leaves the driving lane regardless of the intention of the driver and reduces the risk of traffic accidents by mitigating or avoiding collision by detecting a frontal collision during driving.The main contents of this report are as follows: In case of installing a warning device on a lane departing vehicle (excluding a light vehicle) and a lorry or special vehicle with a total weight exceeding 3.5 tonnes, the driver must continue to operate unless the driver releases the function.In addition, when the automatic emergency braking system is installed, the structure should be such that the braking device is operated automatically after warning the driver when the risk of collision with the running or stopped vehicle in the same direction is detected in front of the driving lane.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.609-612
• /
• 1996

This paper describes a design and implementation of the practical SMPS(Switched Mode Power Supply) with multi-output independent regulation scheme. The designed SMPS is applied to the PSU(Power Supply Unit) of high power GTO drivers for a inverter system. In order to accomplish precise voltage regulations for both turn-on and turn-off bias voltages of the GTO driver, the conventional forward type PWM converter scheme is adopted with the Post Regulator using a Saturable Reactor. Analytic design criteria and control schemes are described for practical applications. Finally, the precise regulation of multi-output voltages is proved by experimental results.

• Journal of Convergence Society for SMB
• /
• v.3 no.1
• /
• pp.31-41
• /
• 2013

There have been various recent methods proposed in detecting driver drowsiness (DD) to avert fatal accidents. This work proposes a hardware/software (HW/SW) co-design approach in implementation of a DD detection system adapted from an AdaBoost-based object detection algorithm with Haar-like features [1] to monitor driver's eye closure rate. In this work, critical functions of the DD detection algorithm is accelerated through custom hardware components in order to speed up processing, while the software component implements the overall control and logical operations to achieve the complete functionality required of the DD detection algorithm. The HW/SW architecture was implemented on an Altera DE2 board with a video daughter board. Performance of the proposed implementation was evaluated and benchmarked against some recent works.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.205-207
• /
• 2008

The new process for hybrid silicon thin film transistor (TFT) using DPSS laser has been developed for realizing both low-temperature poly-Si (LTPS) TFT and a-Si:H TFT on the same substrate as a backplane of active matrix liquid crystal display. LTPS TFTs are integrated on the peripheral area of the panel for gate driver integrated circuit and a-Si:H TFTs are used as a switching device for pixel in the active area. The technology has been developed based on the current a-Si:H TFT fabrication process without introducing ion-doping and activation process and the field effect mobility of $4{\sim}5\;cm^2/V{\cdot}s$ and $0.5\;cm^2/V{\cdot}s$ for each TFT was obtained. The low power consumption, high reliability, and low photosensitivity are realized compared with amorphous silicon gate driver circuit and are demonstrated on the 14.1 inch WXGA+ ($1440{\times}900$) LCD Panel.

• Journal of Information Display
• /
• v.10 no.1
• /
• pp.33-36
• /
• 2009

A new hybrid silicon thin-film transistor (TFT) fabrication process using the DPSS laser crystallization technique was developed in this study to realize low-temperature poly-Si (LTPS) and a-Si:H TFTs on the same substrate as a backplane of the active-matrix liquid crystal flat-panel display (AMLCD). LTPS TFTs were integrated into the peripheral area of the activematrix LCD panel for the gate driver circuit, and a-Si:H TFTs were used as a switching device of the pixel electrode in the active area. The technology was developed based on the current a-Si:H TFT fabrication process in the bottom-gate, back-channel etch-type configuration. The ion-doping and activation processes, which are required in the conventional LTPS technology, were thus not introduced, and the field effect mobility values of $4\sim5cm^2/V{\cdot}s$ and $0.5cm^2/V{\cdot}s$ for the LTPS and a-Si:H TFTs, respectively, were obtained. The application of this technology was demonstrated on the 14.1" WXGA+(1440$\times$900) AMLCD panel, and a smaller area, lower power consumption, higher reliability, and lower photosensitivity were realized in the gate driver circuit that was fabricated in this process compared with the a-Si:H TFT gate driver integration circuit

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.1
• /
• pp.98-106
• /
• 2009

This work proposes a 1280-RGB $\times$ 800-Dot 70.78mW 0.l3um CMOS LCD driver IC (LDI) for high-performance 16M-color low temperature poly silicon (LTPS) thin film transistor liquid crystal display (TFT-LCD) systems such as ultra mobile PC (UMPC) and mobile applications simultaneously requiring high resolution, low power, and small size at high speed. The proposed LDI optimizes power consumption and chip area at high resolution based on a resistor-string based architecture. The single column driver employing a 1:12 MUX architecture drives 12 channels simultaneously to minimize chip area. The implemented class-AB amplifier achieves a rail-to-rail operation with high gain and low power while minimizing the effect of offset and output deviations for high definition. The supply- and temperature-insensitive current reference is implemented on chip with a small number of MOS transistors. A slew enhancement technique applicable to next-generation source drivers, not implemented on this prototype chip, is proposed to reduce power consumption further. The prototype LDI implemented in a 0.13um CMOS technology demonstrates a measured settling time of source driver amplifiers within 1.016us and 1.072us during high-to-low and low-to-high transitions, respectively. The output voltage of source drivers shows a maximum deviation of 11mV. The LDI with an active die area of $12,203um{\times}1500um$ consumes 70.78mW at 1.5V/5.5V.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3078-3080
• /
• 2000

In this paper. we designed a high precision Linear DC Motor(LDM) Driver with $120^{\circ}$ commutation method. It was composed of three parts which were divided into Power and Inverter Circuit. Analog Circuit with PWM Generation and Fault Protections. and Logic Circuit. We selected PMAC Controller by Delta Tau Co. for testifying a high accuracy of a designed driver. A high precision driver enhanced a response to changes of velocity and acceleration in motion and improved the accuracy.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.322-324
• /
• 1994

The 2nd prototype LPM is designed as single side stator structure for improving the thrust force and acceleration time. Experimental results are shown that the static and dynamic characteristics are improved compared with the 1 st prototype. By the computer simulation, the permanent magnet design method is also clarified to desired thrust force. And microstep driver is adopted to the position controller to the designed LPM. The driver suppressed position errors within 1/10 pitch.

• Journal of Power Electronics
• /
• v.2 no.3
• /
• pp.189-198
• /
• 2002

New concept of energy recovery for plasma display panel (PDP) Is proposed. Different from conventional LC resonant sustaining drivers, the current built up before inverting the polarity of the panel electrodes is utilized to change the panel Polarity together with energy Previously charged in Panel capacitance. This operation Provides zero -voltage-switching of switches and reduction of EMI by rejecting the surge current when the sustain switches are turned on. The build-up current helps to reduce transition time of panel polarity and may produce more stable light waveforms. This method shows a desirable characteristic that the circuit loss is similar to that of series resonant type energy recovery circuit which is very effective method.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.311-312
• /
• 2012

Blade pitch control system monitors and adjusts angle of the blades and controls rotation speed of blades. This paper shows 2MW pitch system hardware and electric part. Blade pitch system consists of pitch drive, gear box, motor and energy storage. Fieldbus is base on CANopen protocol. Fail-Safe system moves the blades to a safety position in case of any fault condition. The super capacitor energy storage provides emergency back up to the Pitch servo driver during feathering the blades. This paper studied Blade pitch servo driver and a bi-directional DC-DC converter for fail-safe system.