• Journal of the Korean Society of Safety
• /
• v.28 no.2
• /
• pp.37-41
• /
• 2013

In this work, we report the effect on the volatole organic compounds(VOCs) sensing properties of Copper phthalocyanine(CoPc) and Dilithium phthalocyanine(DiLiPc) thin films onto alumina substrates. Use evaporation method and the spin-coated method for sensing device. The materials of metallophthalocyanine macrocyclic compound solutions blended with N,N'-diphenyl-N,N'-bis(1-naphthyl)-1,1'-biphenyl-4,4"-diamine and/or Poly[2-methoxy-5-(2'-ethylhexyloxy)-1,4-phenylenevinylene] solutions. The influence of the blended in with metallophthalocyanine macrocyclic compounds on the resistance have been measured and analyzed in five different volatole organic compounds. The following results were obtained: The AFM 3D image of thin films deposited on metallophthalocyanine macrocyclic compound shows that the surfaces roughness were about CuPc 4.1~14.3 nm(7.5~8.1%), DiLiPc 10.3~22.2 nm(7.9~11.5%). The resistances decreases upon increasing the concentration of vapor organic compounds to CuPc and DiLiPc thin films. That thin films blended Copper phthalocyanine(CoPc) and Dilithium phthalocyanine(DiLiPc) with N,N'-diphenyl-N,N'-bis(1-naphthyl)-1,1'-biphenyl-4,4"-diamine and/or Poly[2-methoxy--5-(2'-ethylhexyloxy)-1,4-phenylenevinylene]. The resistances of blended thin films with N,N'-diphenyl-N,N'-bis(1-naphthyl)-1,1'-biphenyl-4,4"-diamine and/or Poly[2-methoxy--5-(2'-ethylhexyloxy)-1,4-phenylenevinylene] decreases upon increasing the concentration of volatole organic compounds(VOCs) on DiLiPc than CuPc compound thin films.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.210-216
• /
• 1999

The objective of this paper is to investigate corrosion behaviors of CoCrTa/CrNi thin film and post heat-treatment effect. An electron beam evaporator was used for films deposition. After evaporation, post heat-treatment was carried out under $5.0{\times}10^3$ Torr vacuum condition. Annealing temperature and time were 400 $^{\circ}C$ and 30 min, respectively. To understand the effect of annealing on corrosion behavior of CoCrTa/CrNi, potentiodynamic polarization technique and accelerated corrosion chamber test were undertaken. Corrosion potential is higher for the annealed samples (CoCrTa 400$\AA$/CrNi 1000$\AA$) than for as-deposited one. This is attributed to an enrichment of Cr in the surface layer of the thinfilm resulting in a more corrosion resistant material.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1349_1350
• /
• 2009

Thin films of pp(ST-Co-VA) were fabricated by plasma deposition polymerization (PVDPM) technique. Properties of the plasma polymerized pp(ST-Co-VA) thin films were investigated for application to semiconductor device as insulator. Thickness, dielectric property, composition of the pp(ST-Co-VA) thin films were investigated considering the relationship with preparation condition such as gas pressure and deposition time. In order to verify the possibility of application to organic thin film transistor, a pentacene thin film was deposited on the pp(ST-Co-VA) insulator by vacuum thermal evaporation technique. Crystalline property of the pentacene thin film was investigated by XRD and SEM, FT-IR. Surface properties at the pp(ST-Co-VA)/pentacene interface was investigated by contact angle measurement. The pp(ST-Co-VA) thin film showed a high-k (k=4.6) and good interface characteristic with pentacene semiconducting layer, which indicates that it would be a promising material for organic thin film transistor (OTFT) application.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1993-1997
• /
• 2012

Mg-doped ZnO one-dimensional (1D) nanostrutures were synthesized by using a thermal evaporation technique. The morphology, crystal structure, and sensing properties of the Mg-doped ZnO nanostructures functionalized with Pt to CO gas at $100^{\circ}C$ were examined. The diameters of the 1D nanostructures ranged from 80 to 120 nm and that the lengths were up to a few tens of micrometers. The gas sensors fabricated from multiple networked Mg-doped ZnO nanowires functionalized with Pt showed enhanced electrical response to CO gas. The responses of the nanowires were improved by approximately 70, 69, 111, and 81 times at CO concentrations of 10, 25, 50, and 100 ppm, respectively. Both the response and recovery times of the nanowire sensor for CO gas sensing were not nearly changed by Pt functionalization. It also appeared that the Mg doping concentration did not influence the sensing properties of ZnO nanowires as strongly as Pt-functionalization. In addition, the mechanism for the enhancement in the CO gas sensing properties of Mg-doped ZnO nanowires by Pt functionalization is discussed.

• Journal of the Korean Ceramic Society
• /
• v.34 no.12
• /
• pp.1221-1226
• /
• 1997

The effects of sintering atmosphere and dopant addition on the behavior of densification and grain growth of SnO2 ceramics were investigated with consideration of defect chemistry. CoO and Nb2O5 were chosen as dopants, and oxygen and nitrogen were used for controlling of sintering atmospheres. With the decrease of oxygen partial pressure, densification was depressed due to evaporation of SnO2 ceramics. In the case of SnO2 sintering, the addition of CoO, which produced oxygen vacancy in SnO2 ceramics, led to acceleration of densification and grain growth. On the contrary, when Nb2O5 as a dopant producing Sn vacancy was added to SnO2 ceramics, densification and grain growth were simultaneously retarded. As results, it was conformed that diffusion of oxygen ions was rate determinant in densification and grain growth of SnO2 ceramics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.10a
• /
• pp.59-63
• /
• 2000

BSCCO thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra-low growth rate, and sticking coefficients of the respective elements are evaluated. The sticking coefficient of Bi element exhibits a characteristic temperature dependence : almost a constant value of 0.49 below $730^{\circ}C$ and decreases linearly with temperature over $730^{\circ}C$ This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the Bi(2212) phase formation in the co-deposition process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.94-97
• /
• 2005

Bismuth high Tc superconducting thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra low growth rate, and sticking processing of the respective elements are evaluated. The sticking processing of bismuth element in bismuth high Tc superconducting thin film formation was observed to show a unique temperature dependence; it was almost a constant value of 0.49 below about $730^{\circ}C$ and decreased linearly over about $730^{\circ}C$. This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the bismuth phase formation in the co-deposition process.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.07a
• /
• pp.87-89
• /
• 2003

Thermoplastic polyurethane(PU)-based blend membranes were prepared by the solvent evaporation process. The gas sorption, diffusion, and permeation properties of PU-based blend membranes have been studied. The morphology of PU-based blend membranes was investigated by SEM. The result showed that phase separation occurred with increasing blend ratio. $CO_2$ permeation behaviors of blend membranes were affect by blend composition. Thermoplastic polyurethane(PU)-based membranes showed high $CO_2$ permeation and $CO_2$/$N_2$ selectivity of the blend membrane was improved with increasing the blend ratio.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.213-216
• /
• 1999

BSCCO thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra-low growth rate, and sticking coefficients of the respective elements are evaluated. The sticking coefficient of Bi element exhibits a characteristics temperature dependence : almost a constant value of 0.49 below 730$^{\circ}C$ and decreases linearly with temperature over 730$^{\circ}C$. This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, Bi$_2$O$_3$ from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the Bi(2212) phase formation in the co-deposition process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.193-197
• /
• 2000

BSCCO thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra-low growth rate, and sticking coefficients of the respective elements are evaluated. The sticking coefficient of Bi element exhibits a characteristic temperature dependence : almost a constant value of 0.49 below 73$0^{\circ}C$ and decreases linearly with temperature over 73$0^{\circ}C$. This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, Bi$_2$O$_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the Bi(2212) phase formation in the co-deposition process.