• 한국군사과학기술학회지
• /
• 제23권5호
• /
• pp.475-484
• /
• 2020

Individual curing process of each layer in two resin composites can be caused the separation between two layers. In this study, co-curing process for two resin composites is suggested to improve the inter-layer bonding. Glass fiber reinforced composites with phenolic and epoxy resins were manufactured by co-curing process, and several types of glass/phenolic composites were considered to confirm the application on two resin composites. Experiments for smoke resistance, scratch resistance and flexural strength were carried out to verify requirements corresponding to thermal and mechanical environments. It was validated that two resin composites with phenolic resin impregnated prepreg exhibits good thermal and mechanical characteristics, and it can serve as highly effective composite structures in aerospace and many industry areas.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.83-87
• /
• 2004

In this work, the cure cycle of co-cured metal/composite structure was investigated to decrease fabricating thermal residual stresses between the metal and the composite material. DSC (Differential scanning calorimetry) experiment and static lap shear test of co-cured aluminum/composite double lap joint as well as the curvature experiment of co-cured steel/composite strip were performed to investigate the effect of curing cycle on the thermal residual stress of co-cured hybrid structures. From the experiments, it was found that post curing method after abrupt cooling of co-cured aluminum/composite hybrid structure at certain point of degree of cure during curing process could eliminate fabricating the thermal residual stresses.

• 한국군사과학기술학회지
• /
• 제20권5호
• /
• pp.620-632
• /
• 2017

A chemical vapor curing method(CVC) was developed to cure polycarbosilane(PCS) fibers by using cyclohexene vapour as a non-oxygen active reactant, instead of air in oder to prepare the silicon carbide(SiC) fiber with low oxygen content. A cross-linked PCS fibers by cyclohexene vapor showed a completely different variation in IR spectra in comparison to the air-cured PCS fiber. CVC method resulted in less than 3 wt% in oxygen content. In this experiment conditions, The average tensile strength and modulus of SiC fiber obtained by CVC had 1995 MPa and 183 GPa respectively, which is higher than that of SiC fiber prepared by air-curing process.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.172-175
• /
• 2001

The co-cured Joining method, which is regarded as an adhesively bonded Joining method, is an efficient joining technique because both curing and bonding processes for the composite structures can be achieved simultaneously. It requires neither surface treatment onto the composite adherend nor an additional adhesive joining process because the excess resin, which is extracted from composite materials during consolidation, accomplishes the co-cured Joining process. Since the adhesive of the co-cured joint is the same material as the resin of the composite adherend, the analysis and design of the co-cured joint for composite structures are simpler than those of an adhesively bonded joint, which uses an additional adhesive. In this paper, effects of the manufacturing parameters, namely surface roughness, stacking sequence of the composite adherend, and manufacturing pressure in the autoclave during curing process, on the tensile load bearing capacity of the co-cured single lap joint will be experimentally investigated.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.969-972
• /
• 1992

It is shown that the ac breakdown strength, treeing phenomena, oxidation level, and crystallinity of unaged and aged distribution CV cables vary with XLPE insulations (characterizing anti-oxidation) and curing process. The maximum size of bow-tie tree in insulation influenced on the decrease of ac breakdown strength and the increase of oxidation level and crystallinity of XLPE according to aging time lead to increase the size and density of bow-tie trees.

• 자원리싸이클링
• /
• 제23권4호
• /
• pp.37-46
• /
• 2014

건설 분야 중 건설 재료와 건자재 산업에서 발생하는 $CO_2$는 약 6,700만톤으로 건설 분야에서 발생하는 $CO_2$의 약 30 %를 점유하고 있다. 건설 분야에서 $CO_2$ 저감은 건자재 산업에서 $CO_2$를 발생시키는 2차, 3차 양생을 줄여 소비되는 화석연료 사용과 배출가스 저감의 조절이 필수적이다. 따라서 본 연구는 시멘트 결합재를 기초로 하여 결합재를 40 % 까지 대체하여 모르타르를 제조한 후 양생방법을 달리하여 응결 및 강도 특성을 분석하였다. 결합재 치환율에 따른 강도 특성 결과 증기양생 후 고로슬래그와 CSA 15%, CAMC 5%를 치환한 시험체의 강도 증진이 활발하였다. 특히 고로슬래그 50%, CSA 15%, CAMC 5%를 치환한 시험체가 가장 높게 강도가 증진되었다. 하지만 CAMC 10%의 경우 열팽창에 의한 균열과 온도차에 의한 건조수축, 과도하게 생성된 에트린가이트에 의해 강도가 저하되는 결과를 가져왔다.

• Elastomers and Composites
• /
• 제52권4호
• /
• pp.266-271
• /
• 2017

This study describes the influence of the amount of curing agent and curing temperature on the kinetics of polyurethane elastomers. The urethane prepolymer series was prepared by reacting toluene diisocyanate with polytetramethylene ether glycol at $80^{\circ}C$ for 1 h, and 4,4'-methylene bis(2-chloroaniline) was used as the curing agent. The ratio of the amine group of the curing agent to the isocyanate group of the urethane prepolymer was controlled from 0.85 to 1.05 at curing temperatures ranging from 80 to $120^{\circ}C$. The curing rate of the urethane prepolymer was monitored by observing the change in heat flow during the curing process using differential scanning calorimetry (DSC). As either the content of curing agent or the curing temperature was higher, the conversion rate to the polyurethane elastomer was high. The DSC results were compared with those obtained from using real-time FT-IR.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 추계 학술논문 발표대회
• /
• pp.83-84
• /
• 2018

As the concentration of greenhouse gases in the atmosphere increases, the reduction of CO2 is gaining worldwide attention. In the construction industry, cement replacement materials such as fly ash and blast furnace slag were investigated to reduce CO2 emissions in cement production process. Precast concrete is used in the field after manufacturing in the factory in the form of pipes and bricks because of shortening construction period and cutting construction cost. According to the results of previous research, it is known that early CO2 curing in concrete using OPC or fly ash has an initial strength enhancement effect and can be used for precast concrete production. Therefore, the purpose of this study is to evaluate the strength improvement effect by confirming the initial strength improvement effect when blast furnace slag is mixed.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.194-195
• /
• 2013

Recently, it is the tendency that the CO₂ gas generated in the manufacturing process is increased every year in case of the portland cement used in the most of constructions and civil engineering field. The method that uses the mineral admixtures as the cement substitute material in order to be more serious and as much as it occupies 7% of the global CO₂ gas outlet amount such as 1 ton produces the cement and it ejects the CO₂ gas of 0.4~1.0 ton, etc conclude this problem is examined. Therefore, PVA fiber was mixed into the inorganic binder recycling the blast furnace slag, which is the industrial byproduct with the purpose studying the Geo polymer which doesn't use the cement at all silica fume, red mud, and etc. In addition, the water curing temperature was differentiated and the strength characteristic of the curing body tried to be examined.

• 한국응용과학기술학회지
• /
• 제29권1호
• /
• pp.159-173
• /
• 2012

UV 경화기술은 라디칼 경화와 양이온 경화로서 크게 2 종류로 분류할 수 있다. 이 기술은 플라스틱과 금속간의 여러 기재에 대한 기능성을 개선하기 위해서 표면처리기술에 주로 초점이 맞추어져 왔다. 반면에, Electron beam 기술은 새로운 기능성 재료들을 창출하기 위해 중합공정뿐만 아니라 가교반응들을 다루었다. 이들 두 기술들은 종래의 열경화성 코팅과 비교할 때, 에너지이용 효율과 환경 친화적이어서, 건조와 경화 공정으로 부터 배출되는 탄산가스와 휘발성 유기물을 대폭 감소시킨다. 이 논문에서는 UV 경화 코팅에서 흔히 사용되는 라디칼 경화기술과, 최근의 있는 양이온 경화와 관련된 기술을 다룬 리뷰 논문이다.