• 한국지반공학회논문집
• /
• 제29권5호
• /
• pp.29-38
• /
• 2013

G-class 시멘트는 지열발전소 가동 시에 지열정에서 고온의 지열수나 증기를 심부에서 지표면까지 이동시키는 케이싱을 보호하는 시멘팅 재료로서 이용된다. 지열정을 통한 원활한 지열발전을 위해서는 시멘팅 재료의 물리적 특성들이 만족되어야 한다. 본 연구에서는 G-class 시멘트를 지열정 시멘팅 재료로서의 중요한 물리적 특성인 유동성, 일축압축강도, 열전도도, free fluid 함유율(Free fluid content) 등을 평가하기 위해, 다양한 물/시멘트 비 조건에서 실내실험을 수행하였다. G-class 시멘트에 대한 물리적 특성 평가를 통해 다음과 같은 결론을 도출하였다. (1) G-class 시멘트의 유동성은 소량의 응고지연제(retarder)를 첨가하여 증가 시킬 수 있다. (2) 유동성 확보를 위해 물/시멘트 비를 높일 경우, 일축압축강도가 감소하여 지열정의 구조적 문제를 야기할 수 있다. (3) G-class 시멘트의 열전도도는 지열정 가동 시에 지열정에서 외부 지반으로의 열손실이 거의 없을 정도로 낮게 평가되었다. (4) G-class 시멘트를 시멘팅 재료로 이용할 경우, 블리딩(bleeding) 가능성은 매우 낮은 것으로 판단된다. (5) 페놀프탈레인 지시약은 지열정 시공시 지표면에서 시추용 이수와 G-class 시멘트를 구분하기 위해 적합할 것으로 판단된다.

• 한국지열·수열에너지학회논문집
• /
• 제8권2호
• /
• pp.1-8
• /
• 2012

The G-class cement is usually used for geothermal well grouting to protect a steel casing which is equipped in a geothermal well to transfer geothermal water from deep subsurface to ground surface. In geothermal grouting process, obtaining appropriate fluidity is extremely important in order to fill cement grout flawlessly. In this paper, a series of the V-funnel and Slump Flow test was performed on both of the Portland cement and the G-class cement in order to compare fluidity and filling ability of those kind of cements. In the result of V-funnel test, the fluidity of G-class cement was evaluated much better than the Portland cement at the water/cement ratio of 0.8. In the case of Slump Flow test, the fluidity of G- class cement was estimated slightly better than the Portland cement at both the water/cement ratio of 0.55 and 0.8. Even though the initial fluidity and filling ability of G-class cement were relatively higher than the Portland cement, the results could be considerably changed with time. The results show that the fluidity and filling ability for geothermal well cementation can be properly controlled with water content and additives for adverse geothermal well environment.

• 지질공학
• /
• 제26권1호
• /
• pp.101-115
• /
• 2016

관정의 시멘팅 재료로 사용될 수 있는 두 시멘트 물질(KS-1 보통 포틀랜드, Class G)의 물/고체(고체=시멘트) 중량비와 첨가제인 비산재의 부피함량 변화에 따른 이들 물질들의 물리역학적 물성 변화를 파악하기 위해 실내물리역학실험을 실시하였다. KS-1 보통 포틀랜드 시멘트의 경우 물/고체(고체=시멘트) 중량비를 변화시키며, Class G 시멘트의 경우 물/고체(고체=비산재+시멘트)을 고정한 채 비산재:시멘트의 부피비를 변화시키며 시료를 제작하였다. KS-1 보통 포틀랜드 시멘트의 경우 물/고체 중량비가 증가할수록, Class G 시멘트의 경우 비산재의 함량이 증가할수록, 공극률 증가, 밀도감소, 음파속도(P, S파) 감소. 탄성상수(영율, 포아송비) 감소, 압축 및 인장강도 저하, 열전도도 감소, 비열 증가의 경향을 보였다. 또한 구속압(σ₃)의 증가와 비산재 함량의 증가는 재료의 소성파괴거동을 초래하였다. 이 실내실험결과를 이용하여, 여러 주입공 페라미터(케이싱, 시멘트층의 두께, 주입압, 주입공 경사방향 및 경사각, 주입공 심도)등을 변화 시키면서, 시멘트층의 안정성 분석을 실시하였다. 분석결과 낮은 주입압과 경사정 혹은 수평정에서는 시멘트층이 안정하였으나, 다른 조건에서는 시멘트층에서 주로 인장파괴가 관찰 되었다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제21권2호
• /
• pp.29-37
• /
• 2016

CO₂ injection well sealant is vulnerable to supercritical CO₂ (scCO₂) exposure. To develop an alternative to the conventional sealant system (class G cement/class F fly ash), the performance of slag cement (SPC) systems containing class F fly ash (FFA) or class C fly ash (CFA) was evaluated and compared with the conventional sealant under scCO₂ conditions. All sealant systems showed an immediate increase in compressive strength upon scCO₂ exposure and, at 37.6 MPa, SPC/CFA showed the highest compressive strength after 14 days, which was much higher than the 29.8 MPa of the conventional sealant system. Substantial decreases in porosity were observed in all sealant systems, which were partly responsible for the increase in strength. Carbonation reactions led to pH decreases in the tested sealants from 12.5 to 10~11.6. In particular, the greatest decrease in pH in slag cement/class C fly ash probably supported relatively sustainable alkali activation reactions and the integrity of cement hydrates in this system. XRD revealed the presence of CaCO₃ and a decrease in the content of cement hydrates in the tested sealants upon scCO₂ exposure. TGA demonstrated a greater increase of CaCO₃ and calcium-silicate-hydrate phases in SPC/CFA than in the conventional sealant upon scCO₂ exposure.

• Computers and Concrete
• /
• 제11권6호
• /
• pp.587-602
• /
• 2013

In the current study, a method for concrete compressive strength prediction (based on cement strength class), incorporated in a software package developed by the authors for the estimation of concrete service life under harmful environments, is presented and validated. Prediction of concrete compressive strength, prior to real experimentation, can be a very useful tool for a first mix screening. Given the fact that lower limitations in strength have been set in standards, to attain a minimum of service life, a strength approach is a necessity. Furthermore, considering the number of theoretical attempts on strength predictions so far, it can be seen that although they lack widespread accepted validity, certain empirical expressions are still widely used. The method elaborated in this study, it offers a simple and accurate, compressive strength estimation, in very good agreement with experimental results. A modified version of the Feret's formula is used, since it contains only one adjustable parameter, predicted by knowing the cement strength class. The approach presented in this study can be applied on any cement type, including active additions (fly ash, silica fume) and age.

• Restorative Dentistry and Endodontics
• /
• 제18권1호
• /
• pp.103-113
• /
• 1993

The purpose of this study was to evaluate the tensile bond strength of composite resin inlays according to the their internal surface treatment and types of luting cement and compared them with the conventional direct resin filling thchnique. Class II cavities were prepared in 50 extracted human molar teeth, and then equally divided into five groups. Group 1 : Cavities of control group were directly filled with P-50. Group 2 : Cavities of resin inlay group were luted with resin cement. Group 3 : Cavities of resin inlay group were luted with luting G-I cement. Group 4 : Cavities of resin inlay group were luted with resin cement after sandblasting. Group 5 : Cavities of resin inlay group were luted with luting G-I cement after sandblasting. All specimens were polished with same method and stored in normal saline for 24 hours before testing. An Universal Testing machine(Model No. AGS-100A, Shimadzu, Japan) was used to apply tensile loads in the vertical direction, and the force required for separation was recorded with a cross-head speed of 5mm/min and 100kg in full scale. The results were as follows : 1. The mean tensile bond strength was lowest in group luted with luting G-I cement, with measurements of $14.45{\pm}0.78(kg/cm^2)$ and highest in group luted with resin cement after sandblasting, with measurements of $49.6{\pm}2.74(kg/cm^2)$. 2. The tensile bond strength was greater in resin inlay groups luted with resin cement than in control group and resin inlay groups luted with luting G-I cement(P<0.05). 3. The tensile bond strength was lower in resin inlay groups luted with luting G-I cement than in control group(P<0.05). 4. The tensile bond strength was greater in resin inlay groups luted with resin cement or luting G-I cement after sandblasting than without that(P<0.05).

• 지질공학
• /
• 제26권1호
• /
• pp.117-128
• /
• 2016

시멘트(KS-1 보통 포틀랜드와, Class G)을 이용하여, 시멘트-초임계CO₂ 반응실험과 반응 전/후 시료의 절대투수율 및 강도를 측정하였다. 시멘트 시료는 W/S (Water/Solid)와 fly ash 첨가량을 조절하여 제작하였다. 반응 전 시료의 투수율은 0.009~0.025 mD, 초임계CO₂와 100일간 반응 한 시료의 투수율은 0.11~0.29 mD의 범위로 각각 측정되었다. 반응 후 시료의 투수율이 높게 측정된 이유는, 반응 시료들이 겪은 응력해방으로 인해 균열이 발생하였기 때문이다. 그러나 측정된 투수율은 대부분의 시료에서 API가 추천하는 최대허용 투수율(=0.2 mD)보다 낮다. 초임CO₂에 의한 시멘트 변질은 시료 전체가 아닌 시료의 가장자리에서 일정 두께로 시료의 내부로 발생하였다. 반응영역의 비커스 경도 값이 비반응영역의 것보다 훨씬 높게 측정되었다. 또한 대부분의 시료에서 반응영역 내에서 경도값이 증가한 후 감소하는 현상이 관찰 되었다. 경도값의 증가는 탄산화로 인한 밀도증가, 공극률 감소, 그리고 경도값 감소는 낮은 강도를 갖는 비정질 규산염수화물의 생성이 원인이다.

• 대한치과보철학회지
• /
• 제25권1호
• /
• pp.227-242
• /
• 1987

This study was designed to investigate the pulpal effects of the glass ionomer cement. (Lining cement, G-C Co. Japan) For this purpose, 10 cats were selected, and Class V cavities were prepared on canines of the cats. One experimental group was filled with glass ionomer cement and the other group was filled with zinc phosphate cement . (G-C Co, Japan) The animals of the experimental and control group were sacrificed at 1,2,3,4,6, weeks after the experiment. For comparison of reparative dentin formation pattern in direction of the pulpal and fractured lateral surface, each of them was observed with scanning electron microscope. The findings led to the following conclusions; 1. Reparative dentin of the glass ionomer cement and zinc phosphate cement filling groups were formed on the internal surface of dentin as the shape of hemispherical and spherical with a rough surface. 2. Some of reparative dentin of the glass ionomer cement filling group was started to form at 1 week after experiment, and at 6 weeks after experiment, it had been increased gradually in number and size. 3. Reparative dentin of zinc phosphate cement filling group was formed vigorously, however, gradually was decreased in number and size, and disappeared at 6 weeks after experiment. 4. During the formation of reparative dentin, peritubular dentins were indistinguishable. 5. The diameter of dentinal tubules of reparative dentin has been decreased, during the reparative dentin formed, and it became very irregularly at 6 weeks after experiment.

• 대한조선학회지
• /
• 제7권1호
• /
• pp.57-78
• /
• 1970

The Korea inshore fishing boats are the size up to 30G.T., and their construction commonly employs the traditional wide wooden planking. Nevertheless, the hull forms have been developed with chine-type straight-framed sections which give developable surface party, but not on the whole: especially not on the whole portion of the hull are preferable for them. Considering many merits in the boat construction, the author, excluding cases of the FRP construction by hand lay-up or spray-up method and of the ferro-cement construction, finds out no reasons to depart from the chine-type hull forms of a developable surface in future development of their hull forms, too. In this report, the author proposed new designs of the developable hull surface for four typical boats forming the main structure of Korean inshore fishing fleets; 5G.T.-class multi-purpose boat, 10G.T.-class angling and longlining boat, 20G.T.-class drift and gill netters, and 27G.T.-class stow netters, and presented the tank test results on their propulsion resistance. The tank test had two purposes; one is to present the powering schedule of the new designs and the other to investigate the resistance characteristics of this kinds of boat in comparision with those of equivalent round-type boats at operational speed ranges. Between the both types of the boat no material differences in powering are expected. Hence, the author is confident of that saving in the construction cost of the developable hull over that of the round-type boat may result in considerable contribution to the over-all boat economy.

• Restorative Dentistry and Endodontics
• /
• 제13권1호
• /
• pp.69-78
• /
• 1988

The study was designed to establish a more nearly quantitative method for assessing the marginal leakage of dental restorations. 27 Class V cavities with $45^{\circ}$ bevel joint were prepared and classified into 2 groups. One group was filled with Scotchbond and silux. The other group was filled with glass ionomer cement, Scotchbond and silux. After finishing, all specimens were subjected manually to 100 thermal cycles at $0^{\circ}C$ and $100^{\circ}C$ water-bath. They were soaked in a samarium nitrate solution for 3 hours, irradiated with flux of $6{\times}10^{12}$ neutrons/$cm^2$/sec for 11 hours, cooled for 200 hours, counted with the HPGE detector and the tracer uptake was determined by comparison with a standard of samarium (10 ${\mu}g$). The following results were obtained. 1. Both of the two groups showed a considerable amounts of marginal leakage. 2. The group filled without glass ionomer cement base showed more marginal leakage than the group filled with glass ionomer cement base. 3. Neutron Activation Analysis produced a good quantitative method to measure the marginal leakage and samarium was appropriate to measure the marginal leakage of resin restorations using neutron activation analysis.