• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.3
• /
• pp.26-34
• /
• 1999

A new silicon-based IC interconnect transmission line parameter extraction methodology is presented and experimentally examined. Unlike the PCB or MCM interconnects, a dominant energy propagation mode in the silicon-based IC interconnects is not quasi-TEM but slow wave mode(SWM). The transmission line parameters are extracted taking the silicon substrate effect (i.e., slow wave mode) into account. The capacitances are calculated considering silicon substrate surface as a ground. Whereas the inductances are calculated by using an effective dielectric constant. In order to verify the proposed method, test patterns were designed. Experimental data have agreement within 10%. Further, crosstalk noise simulation shows excellent agreements with the measurements which are performed with high-speed time domain measurement ( i.e., TDR/TDT measurements) for test pattern, while RC model or RLC model without silicon substrate effect show about 20~25% underestimation error.

• Journal of Welding and Joining
• /
• v.20 no.4
• /
• pp.525-534
• /
• 2002

During laser spot welding of the braun tube electron gun, phenomena such as serious spattering and oxidative reaction, etc. were occurred. The spatter occurred from weld pool affects the braun tube, namely it blocks up a very small hole on the shadow mask and causes short circuit between two roles of the electron gun. We guessed that high power density and oxidative reaction are main sources of these problems. So, we studied to prevent and to reduce spatter occurring in spot welding of the braun tube electron gun using pulsed Nd:YAG laser. The characteristics of laser output power was estimated, and the loss of laser energy by optical parameter and spatter was measured by powermeter. The effects of welding parameters, laser defocused distance and incident angle, were investigated on the shape and penetration depth of the laser welded bead in flare and flange joints. From these results, the laser peak power was a major factor to control penetration depth and to occur spatter. It was found that the losses of laser energy by optic parameter and sticked spatter affect seriously laser weldability of thin sheets. The deepest penetration depth is gotten on focal position, and a "bead transition" occurred with a slight displacement of focal position relative to the workpiece surface and the absorption rate of the laser energy is affected by the shape factor of the workpiece. When we changed the incident angle of laser beam, the penetration depth was decreased a little with increasing of the incident angle, and the bead width was increased. The spattering was prevented by considering laser beam energy and incident angle.ent angle.

• Journal of Broadcast Engineering
• /
• v.4 no.2
• /
• pp.164-175
• /
• 1999

Based on the performance analyses for transmission channel and signal characteristics in digital satellite broadcasting system. the optimal design parameter values for system using QPSK modulation technique were proposed in this paper. The proper performance degradation were of 2.0dB for channel characteristics. O.4dB for transmission signal characteristics and 0.2dB for receiver characteristics. respectively. In this case. the design objectives for system parameters were within ${\pm}\;0.5dB$ for gain flatness in 27MHz bandwidth. and O.1nsec/MHz and $0.2sec/MHz^2$ for linear and parabolic group delay. respectively. Also. the optimal parameter values that provide the maximum availability were of OdB OBO for satellite transponder TWTA. and the optimal bandwidth for PLL circuit was of 40kHz with 0.707 damping factor. These analyses and design values can be available for high data rate transmission system via satellite.

• Journal of the Institute of Convergence Signal Processing
• /
• v.11 no.3
• /
• pp.197-202
• /
• 2010

In this paper, multi-channel vital signal monitoring system was implemented for home healthcare. The system able to measure vital signal for example ECG, PPG and temperature simultaneously at patients’ home. The vital signal is an essential parameter for healthcare application and can be easily extracted from patients. The implemented system consist of sensor parts for signal extraction, signal amplifier and filter for analog circuit, analog signal to digital conversion for controlling devices and lastly the monitoring program. The system able to transmit vital signals using Bluetooth wireless communications to personal computer or home server. And the tele-monitoring system able to display real-time signals using web monitoring program. In medical application, the vital signal parameter able to stored and saved in the web server for further medical analysis. This system opens up the possibilities of ubiquitous healthcare where further implementation can be easily done.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.1
• /
• pp.34-40
• /
• 2010

As internet spread widely, various service which use the internet have been provided. One of the service is a internet phone. Its usage is increasing by the advantage of cost. But it has a falling off in quality of speech. because it use packet switching method while existing telephone use circuit switching method. Although vocoder use PLC (Packet Loss Concealment) algorithm, it has a weakness of continuous packet loss. In this paper, we propose methods to improve a lowering in quality of speech under continuous loss of packet by using PLC algorithm used in advanced G.729 and G.711. The proposed methods are LP (Linear Prediction) parameter interpolation, excitation signal reconstruction and excitation signal gain reconstruction. As a result, the proposed method shows superior performance about 11%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.482-487
• /
• 2005

In this paper, we propose the control method of output impedance of each cascode unit cell of distributed amplifier by connecting varactors in the gate-terminal of common gate. Compared to common source unit cell, cascode unit cell has many advantages such as high gain and high output impedance as well as negative resistance loading. But if the transistor model which is used in design is inaccurate and process parameter is changed, oscillation sometimes can occur at band edge in which the gain start to drop. Therefore, we need control circuit which can prevent oscillation, although the circuit has already fabricated, and varactor connected to gate-terminal of common gate of cascode gain cell can play that part. Measured result of fabricated distributed amplifier shows the capability of contol of gain characteristic by adjusting of value of varactors, this can guarantee the stability of the circuit. The gain is $8.92\pm0.82dB$ over 49 GHz, the group delay is $\pm9.3 psec$ over 41 GHz. All transistor which has $0.15{\mu}m$ gate length is GaAs based p-HEMT, and distributed amplifier is put together with 4 stages.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.5
• /
• pp.496-501
• /
• 2009

The thruster head unit of a 300 W cylindrical Hall thruster was developed for the propulsion system of small satellites. The magnetic topology in the thruster channel is a key parameter to achieve high performances. Two types of magnetic circuit structures were designed and manufactured to compare the thrust levels and efficiencies. Also the endurance test was conducted to measure the stable operation duration of the thruster head and to find degree of erosion after extended operation.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1832-1837
• /
• 2011

This paper presents the optimal permanent magnet shape on the rotor of an interior permanent magnet motor to reduce the core losses and improve the performance. As permanent magnet has conductivity inherently, it causes huge amount of eddy current losses by the slot harmonics with concentrated winding. This loss is roughly 100 times larger than that of distributed winding in high speed operation and it cannot be ignored, especially on traction motors. Each eddy current loss on permanent magnet has been investigated in detail by using FEM(Finite Element Method) instead of EMCNM(Equivalent Magnetic Circuit Network Method) in order to consider saturation and non-linear magnetic property. Simulation-based DOE(Design Of Experiment) is also applied to avoid large number of analyses according to each design parameter and consider expected interactions among parameters. Consequently, the optimal design to reduce the core loss on the permanent magnet while maintaining or improving motor performance is proposed by an optimization algorithm using regression equation derived and lastly, the core loss reduction on the proposed shape of the permanent magnet is verified by FEM.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.1
• /
• pp.75-80
• /
• 2010

Noise handing is very important in voice recognition of vehicle environment. that has been studying about to hardware and software approach. hardware method that is noise filter circuit design, basically using Low-pass filter. it was shown a good result. and the side of software that has been developing about to algorithm for Noise canceler, NN(neural network), etc. in this paper we have analysis about to classified parameter pattern matting level for voice recognition on car noise environment that use of DTW(Dynamic Time Warping) which is applicable time series pattern recognition algorithm.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.30-40
• /
• 2015

For a shunt power quality controller (SPQC) the DC side voltage value which is closely related to the compensation performance is a significant parameter. Buy so far, very little discussion has been conducted on this in a quantitative manner by previous publications. In this paper, a method to design the DC side voltage of SPQC is presented according to the compensation performance in the single-phase system and the three-phase system respectively. First, for the reactive current and the harmonic current compensation, a required minimal value of the DC side voltage with a zero total harmonic distortion (THD) of the source current and a unit power factor is obtained for a typical load, through the equivalent circuit analysis and the Fourier Transform analytical expressions. Second, when the DC side voltage of SPQC is lower than the above-obtained minimal value, the quantitative relationship between the DC side voltage and the THD after compensation is also elaborated using the curve diagram. Hardware experimental results verify the design method.