• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.962-964
• /
• 2001

In this paper, the RC filter for mitigating the output overvoltage of the 3-level 3300V 4MW inverter is described. The descriptions on power circuit and overvoltage phenomena are presented. The output transformer which may be used to obtain the higher output voltage, makes the filter design difficult because the parameter measurements are not easy and the accuracy may be poor. So, this paper presents several preliminary results on the output overvoltage with or without transformer to investigate the overall system characteristics. Some experimental results are also provided when the designed filter is applied.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.849-851
• /
• 2001

This paper presents experimental method of parameter measurement and starting characteristics of 3 phase induction motor. Equivalent circuit parameters measured by DC test, the blocked rotor test, and no load test were used as the input data for computer simulation. Starting characteristics, such as starting current and torque were analyzed through computer simulation by Matlab, and the simulation results were compared with experiment using strain gauge attached on motor shaft. We conform that experimental results are very similar to that of simulation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.593-596
• /
• 2002

In this paper, the effect of device model parameter variation on three-dimensional embedded passive devices was investigated using statistical analysis. The optimized equivalent circuit models for several different structures were obtained from HSPICE simulation. The mean and the standard deviation of model parameters were extracted and the sensitivity analysis for each component was performed. From the analysis, the performance and parametric yield of the devices can be analyzed.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.330-335
• /
• 2002

Resistance spot welding is one of the most widely used processes in sheet metal fabrication. Quality assurance of welding has been important to increase the productivity. In this study, weld quality estimation using primary circuit dynamic resistance applied to the in-process real-time systems. For quality estimation, factors relating to quality were extracted from the dynamic resistance, measured in the timer. The relationship between these factors and weld quality was determined through a artificial neural network model. This method has the advantage over the conventional one, such as obtaining the quality information without the use of extra devices.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.8
• /
• pp.849-853
• /
• 2014

In micro-scale electromechanical systems, the power to perform accurate position sensing often greatly exceeds the power needed to generate motion. This paper explores the implications of sampling rate and amplifier noise density selection on the performance of a system identification algorithm using a capacitive sensing circuit. Specific performance objectives are to minimize or limit convergence rate and power consumption to identify the dynamics of a rotary micro-stage. A rearrangement of the conventional recursive least-squares identification algorithm is performed to make operating cost an explicit function of sensor design parameters. It is observed that there is a strong dependence of convergence rate and error on the sampling rate, while energy dependence is driven by error that may be tolerated in the final identified parameters.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.61-67
• /
• 2006

We developed a constant current source which is insensitive to threshold voltage variation caused by irregular grain boundary distribution in polycrystalline silicon. The proposed current source has superior saturation characteristics over wide range of input voltages as well as small current error compared to the previously reported Vth compensated sources. We measured the circuit performance and error in current due to parameter variation by using HSPICE.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.4
• /
• pp.543-551
• /
• 2017

SOL (Short, Open and Load) calibration based on iterative error sensitivity is proposed in this paper. With advanced SOL calibration, unknown parasitic parameters at on-chip terminations are accurately estimated up to 20 GHz. Artificial terminations are designed on printed circuit board (PCB) to experiment the proposed method. On-chip SHORT, OPEN and LOAD fabricated inside silicon shows the accuracy of proposed calibration method through the comparison with known fixture S-parameter after de-embedding.

• Journal of IKEEE
• /
• v.20 no.4
• /
• pp.416-419
• /
• 2016

When the integration density and operating frequency increase in the electronic circuits, it is important to improve the signal transmission characteristics. In this paper, the signal transmission characteristics of the printed circuit boards are analyzed with the curvature of the pads. From the simulation results, signal transmission characteristics are improved when pad curvature increases. Pad curvature more effects on signal transmission characteristics when the thickness of the transmission line and the length of the transmission decrease.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.4
• /
• pp.585-590
• /
• 1993

A wide passband filter consisting of 3-stage ssymmetrical coupler can be realized, where the admittance inverter parameters in equivalent circuit of asymmetrical coupled microstrip lines are given as a function of a fundamental design parameter of a bandpass filter. An experimental filter was designed over 22 percend bandwidth centered at 9GHz and optimized using Super-Compact. Measured forward transmission and forward reflection closely matched design data but measured insertion loss was slightly higher (0.7dB) than the designed value.

• 연구논문집
• /
• s.27
• /
• pp.141-151
• /
• 1997

Recently, the importance of electro-multifunction control valve which is digital control valve is increasing day after day. This is due to the demand of that the current industrial world wants the valve having simpler control circuit and higher operation reliability. It is the PWM controlled high speed electronic valve that satisfies the damands of current industrial world. But, the PWM controlled high speed electronic valve has some non-linearity characteristics like as the delay time of switching and the pressure oscillation phenomenon. These characteristics are an obstacle for the control of high speed & high efficiency in control system. Therefore, in this study, we set the studying purpose on analysis of parameter characteristics in solenoid, and on establishment of optimum design technique in high speed solenoid.