• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.26 no.2
• /
• pp.83-90
• /
• 2018

This paper describes a case study on the design factor analysis of vertical wind tunnel for skydiver's training or experiencing of paradropping exercise in the air. The case study of vertical wind tunnel design is to provide the knowledges on effects of parameter's variation when it is applied to overall or partial duct of tunnel circuit. The analysis of design parameters based on pressure loss are produced one by one through the tunnel components from the flight chamber because the wind tunnel must satisfy the requirement of flight chamber such as flow speed, quality and quantity. Results shows the various effects of parameter variation with pressure loss in the wind tunnel circuit. Pressure loss should be based on the determination of fan and power system which can be selected from market or new design.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.139-142
• /
• 2001

As microeletronics technology continues to progress, there is also a continuous demand on highly integration and miniaturization of systems. For example, it is desirable to package several integrated circuits together in multilayer structure, such as multichip modules, to achieve higher levels of compactness and higher performance. Passive components (i.e., capacitors, resistors, and inductors) are very important for many MCM applications. In addition, the low-temperature co-fired ceramic (LTCC) process has considerable potential for embedding passive components in a small area at a low cost. In this paper, we investigate a method of statistically modeling integrated passive devices from just a small number of test structures. A set of LTCC inductors is fabricated and their scattering parameters (5-parameters) are measured for a range of frequencies from 50MHz to 5GHz. An accurate model for each test structure is obtained by using a building block based modeling methodology and circuit parameter optimization using the HSPICE circuit simulator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.678-681
• /
• 2002

In this paper, Characterization for several 3-D embedded passive elements with different structures was performed. The equivalent circuit optimization for embedded inductor was performed by HSPICE simulation software. After extracting each parameter values, the difference of parameter from each structure was examined. From this work, effective characterization of passive devices with similar structure will be possible.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.54 no.6
• /
• pp.267-273
• /
• 2005

This paper proposes a line-to-ground fault location algorithm for underground cable system. A feature of the proposed method is a new algorithm based on the analytic research which has not been tried until now. The proposed method firstly makes voltage and current equations using analysis of distributed parameter circuit for each of cores and sheathes respectively, and then establishes an equation of the fault distance according to the analysis of the fault conditions. Finally the solution of this equation is calculated by Newton-Raphson iteration method. The effectiveness of this proposed algorithm has been proven through PSCAD/EMTDC(Ver. 4.1) simulations.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2389-2391
• /
• 2000

To design high quality products at low cost is one of very important tasks for engineers. Design optimization for performances can be one solution in this task. There is the robust design which has been proved effectively in many fields of engineering design. In this paper, the concept of robust design is introduced and combined to the fuzzy optimization method and the fuzzy logic system method with non-singleton. These methods are applied for data analysis to get optimum parameters and to reduce experiments. The optimum parameter set points are obtained by the proposed methods. These methods are applied to a filter circuit, a part of the audio circuit of mobile radio transceiver. The simulation results are compared each other. The new methods reduce and predict the effect of parameter variation sources

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.3
• /
• pp.6-11
• /
• 1977

The noise behavior of the Schottky Barrier Gate FET has been investigated by the use of noise equivalent circuit. It has been found that an additional noise source has to be taken into account in the GaAs SBGFET's biased in the pinch-off region; the intervalley scattering noise and the hot electron noise. In this paper, a noise equivalent circuit has been used to determine the noise parameter which was taken into account influence of the saturation velocity of carrier and parasitic resistance.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.1
• /
• pp.11-19
• /
• 2010

Register transfer level power macromodeling is well known as a promising technique for accurate and efficient power estimation. This paper proposes effective approaches based on the tablebased method for the RTL power macro-modeling. The new parameter SD, which characterizes the distribution of switching activities for each gate in the circuit, is one of the contributions. The new parameter SD has strong correlation with power consumption. We also propose an accurate table reference method considering the circuit characteristics. The table reference method is applicable for every table-based method and outputs more accurate power value. The experimental results show that the combination of the proposed methods reduces max error 30.36% in the best case, comparing conventional methods. The RMS error is also improved 1.70% in the best case.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.8
• /
• pp.517-524
• /
• 2004

In this paper, a novel zero-voltage-switching(ZVS) resonant DC-DC converter is proposed. It is composed of two symmetrical active-clamped circuits, the converter can be achieve ZVS in each switches. Also, active clamp capacitor ratios($\alpha$) of proposed circuit can be reduce a peak stress of switching voltage for each main switch. Simulation results using Pspice 9.2 ver and $C^{++}$ characteristic analysis show a provement for the validity of theoretical analysis. The analysis of the proposed Current-Fed Push Pull type DC-DC converter is generally described by using normalized parameter, and achieved an evaluated characteristic values which is needed to design a circuit. We confirm a rightfulness theoretical analysis by comparing a theoretical values and experimental values obtained from experiment using MOSFET as switching devices.

• Proceedings of the KIEE Conference
• /
• 2003.11a
• /
• pp.171-173
• /
• 2003

This paper presents a new fault location algorithm for 3 phase underground cable based on distributed parameter circuit analysis, by which we establish the basic equations for each of core and sheath currents and voltages considering cross-bonding sheaths. The proposed algorithm need simulate by EMTP, and then the EMTP data need be compared with the calculation result in Matlab.

• Proceedings of the KIEE Conference
• /
• 2004.11b
• /
• pp.24-27
• /
• 2004

This paper proposes a new algorithm of underground cable fault location based on the analysis of distributed parameter circuit. The proposed method firstly makes voltage and current equations for each of cores and sheathes respectively, and then establishes an equation of the fault distance according to the analysis of the fault conditions. Finally the solution of this equation is calculated by Newton-Raphson iteration method. The effectiveness of this proposed algorithm has been proven through PSCAD/EMTDC simulations.