• Membrane Journal
• /
• v.29 no.6
• /
• pp.323-328
• /
• 2019

It is a highly important problem for mankind to supply sufficient energy, which has been connected to production and supply of electricity. In terms of the problems, this study fabricated a new sort of solid polymer electrolyte membrane for supercapacitors. The fabricated electrolyte employed grafting poly(oxyethylene methacrylate) (POEM) side chain on poly(vinyl alcohol) (PVA) main chain by free-radical polymerization. It is the first time to utilize PVA-g-POEM graft copolymer as an electrolyte membrane for supercapacitor. The chain behavior of PVA was transformed by grafting POEM side chains, which was analyzed by FT-IR spectra. Also, the capacitance performances of fabricated supercapacitors were explored by cyclic voltammetry (CV), galvanostatic charge/discharge (GCD), and ragone plot. We suggest a new point, the grafting of the electrolyte of supercapacitor in this study.

• The Journal of Advanced Prosthodontics
• /
• v.5 no.2
• /
• pp.84-91
• /
• 2013

PURPOSE. The aim of this study was to evaluate the stability of arginine-glycine-aspartic acid (RGD) peptide coatings on implants by measuring the amount of peptide remaining after installation. MATERIALS AND METHODS. Fluorescent isothiocyanate (FITC)-fixed RGD peptide was coated onto anodized titanium implants (width 4 mm, length 10 mm) using a physical adsorption method (P) or a chemical grafting method (C). Solid Rigid Polyurethane Foam (SRPF) was classified as either hard bone (H) or soft bone (S) according to its density. Two pieces of artificial bone were fixed in a customized jig, and coated implants were installed at the center of the boundary between two pieces of artificial bone. The test groups were classified as: P-H, P-S, C-H, or C-S. After each installation, implants were removed from the SRPF, and the residual amounts and rates of RGD peptide in implants were measured by fluorescence spectrometry. The Kruskal-Wallis test was used for the statistical analysis (${\alpha}$=0.05). RESULTS. Peptide-coating was identified by fluorescence microscopy and XPS. Total coating amount was higher for physical adsorption than chemical grafting. The residual rate of peptide was significantly larger in the P-S group than in the other three groups (P<.05). CONCLUSION. The result of this study suggests that coating doses depend on coating method. Residual amounts of RGD peptide were greater for the physical adsorption method than the chemical grafting method.

• Membrane and Water Treatment
• /
• v.8 no.5
• /
• pp.463-481
• /
• 2017

Bacteria have been considered as a major foulant that initiates the formation of biofilm on the polymeric membrane surface. Some polymeric membranes are naturally antibacterial and have low fouling properties, however, numerous efforts have been devoted to improve their antibacterial performance. These modifications are mostly carried out through blending the membrane with an antibacterial agent or introducing the antibacterial agent on the membrane surface by chemical grafting. Currently, a significant number of researches have reported nanocomposite membrane as a new approach to fabricate an excellent antibacterial membrane. The antibacterial nanoparticles are dispersed homogenously in membrane structure by blending method or coating onto the membrane surface. Aim of the modifications is to prevent the initial attachment of bacteria to membrane surface and kill bacteria when attached on the membrane surface. In this paper, several studies on antibacterial modified membranes, particularly for water treatment, will be reviewed comprehensively. Special attention will be given on polymeric membrane modifications by introducing antibacterial agents through different methods, such as blending, grafting, and coating.

• Elastomers and Composites
• /
• v.49 no.3
• /
• pp.181-190
• /
• 2014

Melt grafting of itaconic acid (IA) onto an ethylene-propylene-diene terpolymer (EPDM) with various organic peroxide initiators was performed. Finding the optimum mixing conditions and concentration of ingredients is critical for effective grafting and optimum properties of grafted materials. This study focused on the effects of mixing conditions (temperature and time), initiator type/concentration and monomer concentration on the grafting degree and efficiency, melt flow index, and gel content of EPDM-g-IA. The initiator, 2,5-dimethyl-2,5-di(tert-butyl peroxy)-hexane (T-101), appeared to meet for the best grafting degree (1.91%). The grafting degree increased markedly by increasing the amounts of monomer IA and initiator T-101. The grafting degree also increased by increasing mixing temperature and time. The optimum monomer and initiator concentrations and reaction temperature and time were found to be about 5wt%/0.05wt% and $160^{\circ}C$/15min, respectively. It was found that the physical properties of EPDM-g-IA were higher than those of the pristine EPDM.

• Journal of Periodontal and Implant Science
• /
• v.47 no.6
• /
• pp.388-401
• /
• 2017

Purpose: The physicochemical properties of a xenograft are very important because they strongly influence the bone regeneration capabilities of the graft material. Even though porcine xenografts have many advantages, only a few porcine xenografts are commercially available, and most of their physicochemical characteristics have yet to be reported. Thus, in this work we aimed to investigate the physicochemical characteristics of a porcine bone grafting material and compare them with those of 2 commercially available bovine xenografts to assess the potential of xenogenic porcine bone graft materials for dental applications. Methods: We used various characterization techniques, such as scanning electron microscopy, the Brunauer-Emmett-Teller adsorption method, atomic force microscopy, Fourier-transform infrared spectroscopy, X-ray diffraction, and others, to compare the physicochemical properties of xenografts of different origins. Results: The porcine bone grafting material had relatively high porosity (78.4%) and a large average specific surface area (SSA; $69.9m^2/g$), with high surface roughness (10-point average roughness, $4.47{\mu}m$) and sub-100-nm hydroxyapatite crystals on the surface. Moreover, this material presented a significant fraction of sub-100-nm pores, with negligible amounts of residual organic substances. Apart from some minor differences, the overall characteristics of the porcine bone grafting material were very similar to those of one of the bovine bone grafting material. However, many of these morphostructural properties were significantly different from the other bovine bone grafting material, which exhibited relatively smooth surface morphology with a porosity of 62.0% and an average SSA of $0.5m^2/g$. Conclusions: Considering that both bovine bone grafting materials have been successfully used in oral surgery applications in the last few decades, this work shows that the porcinederived grafting material possesses most of the key physiochemical characteristics required for its application as a highly efficient xenograft material for bone replacement.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.137-144
• /
• 2012

The surface of polyethylene (PE) was modified through Ar atmospheric pressure plasma treatment and subsequent grafting of glycidyl methacrylate (GMA). Optimum plasma treatment conditions were determined through analyzing the surface free energies calculated from the contact angles between PE samples and three probe liquids, which were RF-power of 200 W, plasma treatment time of 600 sec, Ar flow rate of 5 LPM, and sample-holder moving speed of 20 mm/sec. To introduce the maximum amount of GMA on PE surface treated under the conditions, graft copolymerization conditions such as GMA concentration, temperature, and time were carefully controlled. Grafting degree (GD) was obtained through weight difference analysis of PE film before and after graft copolymerization. A maximum GD was achieved at the GMA concentration of 20 vol%, the temperature of $80^{\circ}C$, and the treatment time of 4 hr.

• Nuclear Engineering and Technology
• /
• v.41 no.8
• /
• pp.1101-1108
• /
• 2009

The ocean contains around eighty elements of the periodic table and uranium is also one among them, with a uniform concentration of 3.3 ppb and a relative abundance factor of 23. With a large coastline, India has a large stake in exploiting the 4 billion tonnes of uranium locked in seawater. The development of radiation grafting techniques, which are useful in incorporating the required functional groups, has led to more efficient adsorbent preparations in various geometrical configurations. Separation based on a polymeric adsorbent is becoming an increasingly popular technique for the extraction of trace heavy metals from seawater. Radiation grafting has provided definite advantages over chemical grafting. Studies related to thermally bonded non woven porous polypropylene fiber sheet substrate characterization and parameters to incorporate specific groups such as acrylonitrile (AN) into polymer back bones have been investigated. The grafted polyacrylonitrile chains were chemically modified to convert acrylonitrile group into an amidoxime group, a chelating group responsible for heavy metal uptake from seawater/brine. The present work has been undertaken to concentrate heavy metal ions from lean solutions from constant potential sources only. A scheme was designed and developed for investigation of the recovery of heavy metal ions such as uranium and vanadium from seawater.

• Applied Chemistry for Engineering
• /
• v.3 no.3
• /
• pp.491-498
• /
• 1992

Graft polymerization of 2-hydroxyethyl methacrylate(HEMA) and styrene, from both their binary and unitary systems, onto polytetrafluoroethylene(PTFE) film was investigated by means of the simultaneous ${\gamma}-ray$ induced method. The effect of various parameters such as monomer concentration, dose rate, absorbed dose, HEMA/styrene feed ratios and the type of diluent on the extent of grafting in unitary and binary systems was studied. It was observed that when unitary HEMA was used for grafting, the grafting extent was very slight, whereas when comonomers were used, a good grafting yield could be obtained. Inclusion of sulfuric acid in the monomer solution resulted in enhanced grafting yields.

• Macromolecular Research
• /
• v.17 no.11
• /
• pp.825-828
• /
• 2009

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.303-309
• /
• 2006

In this study, functional anion-exchange membranes have been prepared and characterized to improve the permeation fluxes of the anion and urea for peritoneum dialysis. They were prepared by UV and radiation graft polymerization methods. The separation-membrane prepared by UV graft polymerization showed the highest grafting degree when HEMA and VBTAC were mixed by 1:2 ratio. However, the grafting degree decreased slightly at compositions above the 1:2 ratio because of the disruption of UV penetration caused by build-up of homopolymer. In the case of photo-initiator, the grafting degree increased up to 0.2 wt%, above which it decreased to a small extent. For the two membranes prepared by radiation graft polymerization, the VBTAC/HEMA membrane showed 96% grafting degree for 6 h reaction time and the GMA membrane showed over 100% grafting degree for 2 h reaction time. Anion-exchange membranes were prepared with 113% grafting degree and with DEA and TEA exchange groups. The DEA membrane showed the conversion degree of 70% in 4 h reaction time while the TEA membrane showed 30% in 2 h reaction time. The prepared anion-exchange membranes were permeable to only anions and urea, but not cations.