• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3252-3258
• /
• 2010

In this study, the effects of the various parameters of spinning and drawing processes on the properties of polyester full drawn yarn (FDY) prepared by steam processing during high-speed spinning were investigated using several techniques. The wet shrinkage ratio of the FDY was able to be manipulated by controlling the temperature and draw ratio. The FDY made using the steam high speed spinning technique exhibited identical properties (such as tenacity, elongation, and wet shrinkage ratio) to that of regular FDY, made using the spin-draw process. FDY prepared using the steam process during high-speed spinning showed excellent dyeability. The dye pick-up of the polyester yarn spun at high-speed spinning was found to be improved when dyed under an atmospheric pressure of $100^{\circ}C$. This result was the same as regular FDY dyed under a high pressure of $130^{\circ}C$.

• Journal of the Korean Chemical Society
• /
• v.55 no.5
• /
• pp.824-829
• /
• 2011

In Fischer-Tropsch Synthesis, because of few reactants ($H_2$, CO), scarce operating parameters affected on efficiency especially the selectivity of products. In this research, effect of operating parameters on the selectivity of Co-Mn-$TiO_2$ Fischer-Tropsch synthesis catalyst were studied by design of experimental procedure and Taguchi method. According to this research, interactions between operating factors have a crucial effect on light products selectivity. Among these interactions, (temperature${\times}$feed ratio) has the main influence on light hydrocarbons selectivity. It was concluded that temperature and feed ratio ($H_2$/CO) were the most integral operating parameters for much greater selectivity of light hydrocarbons.

• Korean Journal of Materials Research
• /
• v.11 no.12
• /
• pp.1028-1034
• /
• 2001

The 2.5 vol% TiNi/6061Al composites were fabricated by permanent mold casting. The microstructures and tensile test for the cold rolled composites with maximum 50% reduction ratio were investigated. In the case of TiNi fiber with 2mm interval in preform, the interface bonding of fabricated composites were good, interface diffusion layer of this composites was made by the mutual diffusion. Transverse section of TiNi fiber was decreased with increasing reduction ratio and longitudinal section of TiNi fiber showed multiple wave phenomenon. And the tensile strength of composites at 38% reduction ratio was the most high. In the case of over 38% reduction ratio, the decrease of the tensile strength was due to TiNi fiber rupture by excess working. The fracture mode was appeared brittle fracture with increasing reduction ratio.

• Korean Chemical Engineering Research
• /
• v.53 no.1
• /
• pp.116-120
• /
• 2015

Synthesis of butenes through dehydration of 2-butanol was investigated over HY zeolite catalysts. 2-Butanol dehydration reaction was carried out in a fixed bed catalytic reactor. 2-Butanol conversion was increased with increase of $Si/Al_2$ ratio of HY zeolite catalysts, which can be ascribed to increase of acid strength with increase of $Si/Al_2$ ratio. Selectivities to 1-butene, trans-2-butene, and cis-2-butene were not greatly influenced by the change of the $Si/Al_2$ ratio of HY zeolite. As a result, it was advantageous to use a HY zeolite catalyst with 60 $Si/Al_2$ ratio for maximizing the yield of 1-butene in the dehydration of 2-butanol. The optimal reaction temperature for maximizing the yield of 1-butene was $250^{\circ}C$ over HY (60) catalyst.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.677-684
• /
• 2013

A mixed refrigerant cycle (MRC) has been widely used in liquefaction of natural gas because it is simple and easily operable with reasonable equipment costs. One of the important techniques in MRC is selection of a refrigerant mixture and decision of its optimum mixing ratio. In this work, it is examined whether mixture components (refrigerants) and their mixing ratio influence performance of general MRC processes. In doing this, mixture design and response surface method, which are well-known statistical techniques, are used to find optimal mixture refrigerants and their optimal mixing ratio that minimize total energy consumption of the entire liquefaction process. A MRC process using several refrigerants and various mixing ratios is simulated by Aspen HYSYS and mixture design and response surface method are implemented using Minitab. According to the results, methane ($C_1$), ethane ($C_2$), propane ($C_3$) and nitrogen ($N_2$) are selected as best mixture refrigerants and the determined mixture ratio (mole ration) can reduce total energy consumption by up to 50%.

• Elastomers and Composites
• /
• v.50 no.2
• /
• pp.103-109
• /
• 2015

In this study, epoxy/anhydride mixing ratio for the highly silica filled compounds with chromium (III) octoate catalyst was investigated at a low curing temperature ($71^{\circ}C$ for 40 hr) by evaluating the compressive strength with the weight ratio ranges from 0.3/1.0 to 1.0/1.0 of epoxy part (Part A)/anhydride part (Part B). In case of epoxy/anhydride compounds used surface unmodified silica by coupling agent, these compounds need excess anhydride unlike the weight ratio in the conventional epoxy/anhydride compounds. In curing behavior, the epoxy/anhydride compounds containing chromium (III) octoate showed high conversions at $71^{\circ}C$ for 40 hr, even if a dipropylene glycol (DPG) was not used as a polymerization initiator. Also, DPG leads to a poor epoxy network structure. In conclusion, the appropriate weight ratio of Part A/Part B of highly silica filled epoxy/anhydride compounds with chromium (III) octoate catalyst is 0.5/1.0 and the maximum amounts of silica is 1470 phr of epoxy resin.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.2A
• /
• pp.105-113
• /
• 2011

This study evaluated the effects of fibers on the mechanical properties and chemical solution resistance of porous concrete with fiber type (jute, pulp, PVA and nylon fiber) and fiber volume fraction (0.0%, 0.1%, 0.2%, 0.3%). The tests that were carried out to analysis the properties of porous concrete included compressive strength, void ratio, pH value, and chemical solution exposure with varying type and volume fraction of fiber were conducted. The type and volume fraction of fiber also affected the void ratio, compressive strength, flexural strength and chemical solution exposure. Increased volume fractions of fiber resulted in improved properties of the compressive strength, flexural strength and void ratio. However, the difference between the measured pH value and chemical resistance of porous concrete with fiber type and volume fraction was not significant.

• Carbon letters
• /
• v.28
• /
• pp.72-80
• /
• 2018

In this study, an empirical relationship between the energy band gap of multi-walled carbon nanotubes (MWCNTs) and synthesis parameters in a chemical vapor deposition (CVD) reactor using factorial design of experiment was established. A bimetallic (Fe-Ni) catalyst supported on $CaCO_3$ was synthesized via wet impregnation technique and used for MWCNT growth. The effects of synthesis parameters such as temperature, time, acetylene flow rate, and argon carrier gas flow rate on the MWCNTs energy gap, yield, and aspect ratio were investigated. The as-prepared supported bimetallic catalyst and the MWCNTs were characterized for their morphologies, microstructures, elemental composition, thermal profiles and surface areas by high-resolution scanning electron microscope, high resolution transmission electron microscope, energy dispersive X-ray spectroscopy, thermal gravimetry analysis and Brunauer-Emmett-Teller. A regression model was developed to establish the relationship between band gap energy, MWCNTs yield and aspect ratio. The results revealed that the optimum conditions to obtain high yield and quality MWCNTs of 159.9% were: temperature ($700^{\circ}C$), time (55 min), argon flow rate ($230.37mL\;min^{-1}$) and acetylene flow rate ($150mL\;min^{-1}$) respectively. The developed regression models demonstrated that the estimated values for the three response variables; energy gap, yield and aspect ratio, were 0.246 eV, 557.64 and 0.82. The regression models showed that the energy band gap, yield, and aspect ratio of the MWCNTs were largely influenced by the synthesis parameters and can be controlled in a CVD reactor.

• Macromolecular Research
• /
• v.10 no.5
• /
• pp.253-258
• /
• 2002

The multi-wall carbon nanotubes (MWNTs) with graphite crystal structure were synthesized by the catalytic decomposition of a ferrocene-xylene mixture in a quartz tube reactor to use as the conductive filler in the binary polymer matrix composed of poly(vinylidene fluoride) (PVdF) and poly(vinyl pyrrolidone) (PVP) for the EMI (electromagnetic interference) shielding applications. The yield of MWNTS was significantly dependent on the reaction temperature and the mole ratio of ferrocene to xylene, approaching to the maximum at 800 $^{\circ}C$ and 0.065 mole ratio. The electrical conductivity of the MWNTs-filled PVdF/PVP composite proportionally depended on the mass ratio of MWNTs to the binary polymer matrix, enhancing significantly from 0.56 to 26.7 S/cm with the raise of the mass ratio of MWNTs from 0.1 to 0.4. Based on the higher electrical conductivity and better EMI shielding effectiveness than the carbon nanofibers (CNFs)-filled coating materials, the MWNTs-filled binary polymer matrix showed a prospective possibility to apply to the EMI shielding materials. Moreover, the good adhesive strength confirmed that the binary polymer matrix could be used for improving the plastic properties of the EMI shielding materials.

• Conservation and Restoration of Cultural Heritage
• /
• v.1 no.1
• /
• pp.3-8
• /
• 2012

Chemical compositions and lead isotope ratios for four glass bead samples of Seokga-tap were analyzed and the results were organized. Among 4 glass beads found in the Seokga-tap, 3 pieces were lead glass. Manufacturing method was to firstly grind pebbles finely and mix lead ore to be melt at $740{\sim}760^{\circ}C$. The mixed ratio of silica and lead was 3:7. Moreover, The evaluation on the lead isotope ratio indicated that two lead glass pieces used lead ore from northern Korea. One piece has the direction of southern Korea lead ore, but it requires a further review. One glass bead of Seokga-tap was brown and it was potash lead glass ($K_2O-PbO-SiO_2$) System. The mixed ratio was approximately 50:10:40 for silica, natural saltpeter, and lead, respectively. Lead isotope ratio data fell within the lead ore from northern China. Therefore, it was concluded that potash lead glass found in the Seokga-tap was produced in northern area of China at the end of $10^{th}$ century and transferred to the Seokga-tap.