• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1591-1593
• /
• 1997

The purpose of this study is to research and develop $Li_xV_3O_8$ composite cathode for lithium polymer battery. We investigated electrochemical, interfacial properties and charge/discharge cycling of $Li_xV_3O_8$/SPE/Li cell. The radius of semicircle associated with the interfacial resistance of $Li_xV_3O_8$/SPE/Li cell increased very slowly during discharge process from 100% SOC to 90% SOC. And then the cell resistance was increased at discharge process from 10% SOC to 0% SOC. The discharge capacity based on $Li_xV_3O_8$ was 212mAh/g at 15th cycle. The $Li_xV_3O_8$/SPE/Li cell has a good properties.

• 한국수소및신에너지학회논문집
• /
• 제25권3호
• /
• pp.311-318
• /
• 2014

Performance degradation of a battery in 20 kWh energy storage system (ESS) under various operating conditions was studied. And energy saving of the ESS was also monitored by connecting with 20 kW photovoltaic (PV). PV-connected ESS saved 5~7% of energy consumption in 2013 compared to that without such system in 2012. As charge-discharge cycle increased, capacity decreased and the performance degradation was glaringly obvious after 40 cycles. And as charge and discharge rate increased, the performance degradation was more serious. After 50 charge-discharge cycles, a lot of degraded product was deposited on the surface of anode and cathode electrodes, and the cathode side was more contaminated. Therefore, in order to maintain the cell performance, it was more important to protect the degradation of the cathode side.

• 전기학회논문지
• /
• 제63권8호
• /
• pp.1033-1038
• /
• 2014

Electric vehicles should be connected to power system for charge and discharge of battery. Besides vehicle's battery is charged for a power source, it is also reversibly possible to provide power source from battery to power system. Researches on battery usage for regulation resources have been progressed and could cause cost increase excessively because they distribute regulation capacity equally without considering the battery wear cost of SOC, temperature, voltage and so on. This causes increase of grid maintenance cost and aggravate economical efficiency. In this paper it is studied that the cost could be minimized according to the battery condition and characteristic. The equation is developed in this paper to calculate the possible number of charge and discharge cycle, according to SOC level and weighting factors representing the relation between battery life and temperature as well as voltage. Thereafter, the correlation is inferred between the battery condition and wear cost reflecting the battery price, and the expense of compensation is decided according to the condition on battery wear-out of vehicle. In addition, using realtime error between load and load expectation, it is calculated how much regulation capacity should be provided.

• 전력전자학회논문지
• /
• 제5권5호
• /
• pp.435-442
• /
• 2000

리튬폴리머전지의 전기적인 특성을 평가하고 이것을 시스템 측면에서 고찰할 수 있는 이론적인 토대를 마련하기 위하여 본 논문에서는 전지의 전기적인 특성평가를 위한 전기적모델링 기법에 관하여 고찰하였다. 실제 제작된 리튬폴리머전지의 특성자료를 바탕으로 R-L-C 모델을 이용한 동적해석방식과 PSpice 모델을 이용한 정적해석방식을 통하여 리튬폴리머전지의 전기적 특성을 해석하였다. 각 모델의 풍/방전시의 전기적 특성을 고찰하고 충/방전조건에 따른 전지의 단자전압등 특성변수의 변화를 실제 제작된 리튬폴리머전지와 비친, 검토하여 그 타당성을 검증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1594-1596
• /
• 1997

$LiMn_2O_4$ is prepared by reacting stoichiometric mixture of LiOH $H_2O$ and $MnO_2$ (mole ratio 1 : 2) and calcinating at $800^{\circ}C$ for 24h, 36h, 48h, 60h and 72h. At X-ray diffraction, cathode active materials calcined at $800^{\circ}C$ for 36h. (111)/(311) peak ratio was 0.37. It was that crystal structure is formed very well. In the result of charge/discharge test, when heated at $800^{\circ}C$ for 36h, charge/discharge characteristics of $LiMn_2O_4$ is the best and Super-s-black sort of conductive agent showed well property. Also, AC impedance creased gradually during cycling and stabilized after 10cycle.

• 전기화학회지
• /
• 제5권1호
• /
• pp.30-38
• /
• 2002

탄화수소가스를 고온$(1000^{\circ}C)$에서 열분해 하여 고상화하는 기상 열분해법을 사용하여 저결정질 탄소재를 제조하고 같은 방법으로 붕소를 첨가한 저결정질 탄소재$C_{l-x}B_x(x=0.05,\;0.10,\;0.20)$를 제조하여, 리튬 이온 이차전지의 부극으로서의 전기화학적 특성을 조사하였다. 시료 대 PVDF를 95:5의 무게비로 첨가한 경우, 붕소를 첨가하지 않은 저 결정질 탄소재(x=0.00)는 초기 방전용량 374mAh/g을 나타내었으며, 제 2싸이클부터는 싸이클 성능이 비교적 우수하여 제 10싸이클에서 258mAh/g의 방전용량을 나타내었다. 시료 대 PVDF를 95:5의 무게비로 첨가한 경우, $C_{1-x}B_x(x=0.00,\;0.05,\;0.10\;0.20)$ 시료들 중에서 x=0.05 조성의 시료는 가장 큰 초기 방전용량 860mAh/g을 나타내었으며, 10번째 싸이클에서 181mAh/g의 방전용량을 나타내었다. 제 2싸이클부터 싸이클 성능은 모두가 비슷하게 나타났다 초기방전 용량(PVDF $10wt.\%$ 사용시, 853mAh/g), 싸이클 성능, 방전용량(PVDF $10wt.\%$사용시 10번째 싸이클에서 400mAh/g)면에서 $C_{0.90}B_{0.10}$ 시료가 리튬이온 이차전지의 부극으로서의 가장 우수한 전기화학적 특성을 나타내었다. 합성한 탄소에 NMP를 용매로 한 액상 혼합 바인더(PVDF)를 90:10의 무게비로 첨가한 경우가 95:5의 무게비로 첨가한 경우보다 대체로 모든 조성에서 충$\cdot$방전용량이 크게 나타났다. 붕소가 첨가되어 덜 disordered된 구조가 됨으로써 1.25V보다 낮은 전압 부분에서 평탄구역이 증가하는 것으로 판단된다. 붕소가 첨가된 경우 충$\cdot$방전용량이 제 2싸이클에서부터 급격히 감소하였는데, 이는 첨가된 붕소가 제 1싸이클에서 삽입되는 Li과 일부는 강하게 결합하여 추출이 안되고 일부만이 다시 가역적으로 추출$\cdot$삽입되기 때문으로 생각된다. 붕소 첨가에 의한 충$\cdot$방전용량의 증가는, 붕소가 electron acceptor로 작용하여 삽입된 Li와 붕소-탄소 host 사이의 결합 강도를 증가시킴으로써 붕소치환 된 탄소에서 Li의 전위를 상승시키기 때문에 일어난다고 사려된다.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권4호
• /
• pp.317-324
• /
• 1994

In this study, new preparation method of LiCoO$_{2}$ was applied to develop cathode active material for Li rechargeable cell, and followed by X-ray diffraction analysis, electrochemical properties and initial charge/discharge characteristics as function of current density. HC8A72- and CC9A24-LiCoO$_{2}$ were prepared by heating treatment of the mixture of LiOH H$_{2}$O/CoCO$_{3}$(1:1 mole ratio) and the mixture of Li$_{2}$CO$_{3}$/CoCO$_{3}$(1:2 mole ratio) at 850 and 900.deg. C, respectively. Two prepared LiCoO$_{2}$s were identified as same structure by X-ray diffraction analysis. a and c lattice constant were 2.816.angs. and 14.046.angs., respectively. The electrochemical potential of CFM-LiCoO$_{2}$(Cyprus Foote Mineral Co.'s product), HC8A72-LiCoO$_{2}$ and CC9A24 LiCoO$_{2}$ electrode were approximately between 3.32V and 3.42V vs. Li/Li reference electrode. Stable cycling behavior was obtained during the cyclic voltammetry of LiCoO$_{2}$ electrode. According as scan rate increases, cathodic capacity decreases, but redox coulombic efficiency was about 100% at potential range between 3.6V and 4.2V vs. Li/Li reference electrode. Cathodic capacity of HC8A72-LiCoO$_{2}$ was 32% higher than that of CFM-LiCoO$_{2}$ and that of CC9A24-LiCoO$_{2}$ was 47% lower than that of CFM-LiCoO$_{2}$ at 130th cycle in the condition of lmV/sec scan rate. Constant cur-rent charge/discharge characteristics of LiCoO$_{2}$/Li cell showed increasing Ah efficiency with initial charge/discharge cycle. Specific discharge capacities of CFM and HC8A72-LiCoO$_{2}$ cathode active materials were about 93mAh/g correspondent to 34% of theretical value, 110mAh/g correspondent to 40% of theretical value, respectively. In the view of reversibility, HC8A72-LiCoO$_{2}$ was also more excellent than CFM- and CC9A24-LiCoO$_{2}$.

• 한국수소및신에너지학회논문집
• /
• 제17권1호
• /
• pp.31-38
• /
• 2006

There are two types of metal hydride electrodes as a negative electrode in a Ni-MH battery, $AB_2$ Zr-based Laves phases and $AB_5$ LM(La-rich mischmetal)-based alloys. The $AB_5$ alloy electrodes have characteristic properties such as a large discharge capacity per volume, easiness in activation, long cycle life and a low cost of alloy. However they have a relatively small discharge capacity per weight. The $AB_2$alloy electrodes have a much higher discharge capacity per weight than $AB_5$ alloy electrodes, however they have some disadvantages of poor activation behavior and cycle life. Therefore, in order to improve the discharge capacity of the $AB_5$ alloy electrode the Zr, Ti and V which are the alloying elements of the $AB_2$ alloys were added to the $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}$ alloy which was chosen as a $AB_5$ alloy with a high capacity. The addition of Zr, Ti and V to $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}$ alloy improved the activation to be completed in two cycles. The discharge capacities of Zr 0.02, Ti 0.02 and V 0.1 alloys in $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V) were respectively 346, 348 and 366 mAh/g alloy. The alloy electrodes, Zr 0.02, Ti 0.05 and V 0.1 in $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V), have shown good cycle property after 200 cycles. The rate capability of the $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V) alloy electrodes were very good until 0.6 C rate and the alloys, Zr 0.02, Ti 0.05 and V 0.1, have shown the best result as 92 % at 2.4 C rate. The charge retention property of the $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V) alloys was not good and the alloys with M content from 0.02 to 0.05 showed better charge retention properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.455-458
• /
• 2001

Spinel $LiMn_{2-y}$$M_{y}$ $O_4$powder was prepared solid-state method by calcining the mixture of LiOH - $H_2O$, Mn $O_2$, ZnO and MgO at 80$0^{\circ}C$ for 36h. To investigate the effect of substitution with Mg, Zn cation, charge-discharge experiments and initial impedance spectroscopy performed. The structure of $LiMn_{2-y}$$M_{y}$ $O_4$crystallites was analyzed from powder X-ray diffraction data as a cubic spinel, space group Fd3m. all cathode material showed spinel phase based on cubic phase in X-ray diffraction. Ununiform which calculated by (111) face and (222) face was constant in spite of the change of y value, except PUf\ulcorner LiM $n_2$ $O_4$. The discharge capacities of the cathode for the cation subbstitUtes $LiMn_{2-y}$$M_{y}$ $O_4$/Li cell at the 1st cycle and at the 40th cycle were about 120~124 and 108~112mAh/g except LiM $n_{1.9}$Z $n_{0.1}$ $O_4$/Li cell, respectively. This cell capacity is retained by 93% after 40th cycle. AC impedance of $LiMn_{2-y}$$M_{y}$ $O_4$/Li cells revealed the similar resistance of about 65~110$\Omega$ before cycling. before cycling.g.g.

• 한국전기전자재료학회논문지
• /
• 제14권8호
• /
• pp.663-669
• /
• 2001

Spinel LiM $n_2$ $O_4$ and LiM $n_{1.9}$M $g_{0.1}$ $O_4$ power was synthesized with solid-state method by calcining the mixture of LiOH.$H_2O$, Mn $O_2$ and MgO at 80$0^{\circ}C$ for 36 h in an air atmosphere. To investigate the effect of temperature on he cycle performance of cathode material during cycling, charge-discharge experiments and ac impedance measurement were performed. Initial discharge capacity was gradually increased with the increase of charge-discharge temperature. Discharge capacity at high temperature was suddenly decreased during cycling. On the other hand, discharge capacity at low temperature was almost constant during cycling. It confirmed that Mn dissolution is serious at high temperature than at low temperature. LiM $n_2$ $O_4$ and LiM $n_{1.9}$M $g_{0.1}$ $O_4$ showed the best capacity and stability at room temperature.ure.ure.